/*
 * Copyright (c) 2018, Texas Instruments Incorporated - http://www.ti.com/
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. Neither the name of the copyright holder nor the names of its
 *    contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE
 * COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
 * OF THE POSSIBILITY OF SUCH DAMAGE.
 */
/*---------------------------------------------------------------------------*/
// Parameter summary
// Adv. Address: 010203040506
// Adv. Data: dummy
// BLE Channel: 17
// Extended Header: 09 09 010203040506 babe
// Frequency: 2440 MHz
// PDU Payload length:: 30
// TX Power: 5 dBm (requires define CCFG_FORCE_VDDR_HH = 0 in ccfg.c, see CC13xx/CC26xx Technical Reference Manual)
// Whitening: true
/*---------------------------------------------------------------------------*/
#include "sys/cc.h"
/*---------------------------------------------------------------------------*/
#include <ti/devices/DeviceFamily.h>
#include DeviceFamily_constructPath(driverlib/rf_mailbox.h)
#include DeviceFamily_constructPath(driverlib/rf_common_cmd.h)
#include DeviceFamily_constructPath(driverlib/rf_ble_cmd.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_bt5.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_rfe_bt5.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_mce_bt5.h)

#include <ti/drivers/rf/RF.h>

#include "ble-settings.h"
/*---------------------------------------------------------------------------*/
// TI-RTOS RF Mode Object
RF_Mode rf_ble_mode =
{
    .rfMode = RF_MODE_AUTO,
    .cpePatchFxn = &rf_patch_cpe_bt5,
    .mcePatchFxn = &rf_patch_mce_bt5,
    .rfePatchFxn = &rf_patch_rfe_bt5,
};
/*---------------------------------------------------------------------------*/
// TX Power table
// The RF_TxPowerTable_DEFAULT_PA_ENTRY macro is defined in RF.h and requires the following arguments:
// RF_TxPowerTable_DEFAULT_PA_ENTRY(bias, gain, boost coefficient)
// See the Technical Reference Manual for further details about the "txPower" Command field.
// The PA settings require the CCFG_FORCE_VDDR_HH = 0 unless stated otherwise.
RF_TxPowerTable_Entry rf_ble_tx_power_table[RF_BLE_TX_POWER_TABLE_SIZE+1] =
{
    {-21, RF_TxPowerTable_DEFAULT_PA_ENTRY(7, 3, 0, 3) },
    {-18, RF_TxPowerTable_DEFAULT_PA_ENTRY(9, 3, 0, 3) },
    {-15, RF_TxPowerTable_DEFAULT_PA_ENTRY(8, 2, 0, 6) },
    {-12, RF_TxPowerTable_DEFAULT_PA_ENTRY(10, 2, 0, 8) },
    {-10, RF_TxPowerTable_DEFAULT_PA_ENTRY(12, 2, 0, 11) },
    {-9, RF_TxPowerTable_DEFAULT_PA_ENTRY(13, 2, 0, 5) },
    {-6, RF_TxPowerTable_DEFAULT_PA_ENTRY(13, 1, 0, 16) },
    {-5, RF_TxPowerTable_DEFAULT_PA_ENTRY(14, 1, 0, 17) },
    {-3, RF_TxPowerTable_DEFAULT_PA_ENTRY(17, 1, 0, 20) },
    {0, RF_TxPowerTable_DEFAULT_PA_ENTRY(25, 1, 0, 26) },
    {1, RF_TxPowerTable_DEFAULT_PA_ENTRY(28, 1, 0, 28) },
    {2, RF_TxPowerTable_DEFAULT_PA_ENTRY(13, 0, 0, 34) },
    {3, RF_TxPowerTable_DEFAULT_PA_ENTRY(17, 0, 0, 42) },
    {4, RF_TxPowerTable_DEFAULT_PA_ENTRY(22, 0, 0, 54) },
    {5, RF_TxPowerTable_DEFAULT_PA_ENTRY(30, 0, 0, 74) },
    RF_TxPowerTable_TERMINATION_ENTRY
};
/*---------------------------------------------------------------------------*/
// Overrides for CMD_BLE5_RADIO_SETUP
uint32_t rf_ble_overrides_common[] CC_ALIGN(4) =
{
                                   // override_ble5_setup_override_common.xml
    (uint32_t)0x02400403,          // Synth: Use 48 MHz crystal, enable extra PLL filtering
    (uint32_t)0x001C8473,          // Synth: Configure extra PLL filtering
    (uint32_t)0x00088433,          // Synth: Configure synth hardware
    (uint32_t)0x00038793,          // Synth: Set minimum RTRIM to 3
    HW32_ARRAY_OVERRIDE(0x4004,1), // Synth: Configure faster calibration
    (uint32_t)0x1C0C0618,          // Synth: Configure faster calibration
    (uint32_t)0xC00401A1,          // Synth: Configure faster calibration
    (uint32_t)0x00010101,          // Synth: Configure faster calibration
    (uint32_t)0xC0040141,          // Synth: Configure faster calibration
    (uint32_t)0x00214AD3,          // Synth: Configure faster calibration
    (uint32_t)0x02980243,          // Synth: Decrease synth programming time-out (0x0298 RAT ticks = 166 us)
    (uint32_t)0xFCFC08C3,          // DC/DC regulator: In Tx, use DCDCCTL5[3:0]=0xC (DITHER_EN=1 and IPEAK=4). In Rx, use DCDCCTL5[3:0]=0xC (DITHER_EN=1 and IPEAK=4).
    (uint32_t)0x00038883,          // Rx: Set LNA bias current offset to adjust +3 (default: 0)
    (uint32_t)0x000288A3,          // Rx: Set RSSI offset to adjust reported RSSI by -2 dB (default: 0)
    (uint32_t)0x01080263,          // Bluetooth 5: Compensate for reduced pilot tone length
    (uint32_t)0x08E90AA3,          // Bluetooth 5: Compensate for reduced pilot tone length
    (uint32_t)0x00068BA3,          // Bluetooth 5: Compensate for reduced pilot tone length
    (uint32_t)0x0E490C83,          // Bluetooth 5: Set correct total clock accuracy for received AuxPtr assuming local sleep clock of 50 ppm
    (uint32_t)0xFFFFFFFF,
};
/*---------------------------------------------------------------------------*/
// Overrides for CMD_BLE5_RADIO_SETUP
uint32_t rf_ble_overrides_1mbps[] CC_ALIGN(4) =
{
                                    // override_ble5_setup_override_1mbps.xml
    MCE_RFE_OVERRIDE(1,0,0,1,0,0),  // PHY: Use MCE RAM patch (mode 0), RFE RAM patch (mode 0)
    HW_REG_OVERRIDE(0x5320,0x0240), // Bluetooth 5: Reduce pilot tone length
    (uint32_t)0x013302A3,           // Bluetooth 5: Compensate for reduced pilot tone length
    (uint32_t)0xFFFFFFFF,
};
/*---------------------------------------------------------------------------*/
// Overrides for CMD_BLE5_RADIO_SETUP
uint32_t rf_ble_overrides_2mbps[] CC_ALIGN(4) =
{
                                    // override_ble5_setup_override_2mbps.xml
    MCE_RFE_OVERRIDE(1,0,2,1,0,2),  // PHY: Use MCE RAM patch (mode 2), RFE RAM patch (mode 2)
    HW_REG_OVERRIDE(0x5320,0x0240), // Bluetooth 5: Reduce pilot tone length
    (uint32_t)0x00D102A3,           // Bluetooth 5: Compensate for reduced pilot tone length
    (uint32_t)0xFFFFFFFF,
};
/*---------------------------------------------------------------------------*/
// Overrides for CMD_BLE5_RADIO_SETUP
uint32_t rf_ble_overrides_coded[] CC_ALIGN(4) =
{
                                    // override_ble5_setup_override_coded.xml
    MCE_RFE_OVERRIDE(1,0,1,1,0,1),  // PHY: Use MCE RAM patch (mode 1), RFE RAM patch (mode 1)
    HW_REG_OVERRIDE(0x5320,0x0240), // Bluetooth 5: Reduce pilot tone length
    (uint32_t)0x078902A3,           // Bluetooth 5: Compensate for reduced pilot tone length
    (uint32_t)0xFFFFFFFF,
};
/*---------------------------------------------------------------------------*/
// CMD_BLE5_RADIO_SETUP
// Bluetooth 5 Radio Setup Command for all PHYs
rfc_CMD_BLE5_RADIO_SETUP_t rf_cmd_ble5_radio_setup =
{
    .commandNo = 0x1820,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .startTime = 0x00000000,
    .startTrigger.triggerType = 0x0,
    .startTrigger.bEnaCmd = 0x0,
    .startTrigger.triggerNo = 0x0,
    .startTrigger.pastTrig = 0x0,
    .condition.rule = 0x1,
    .condition.nSkip = 0x0,
    .defaultPhy.mainMode = 0x0,
    .defaultPhy.coding = 0x0,
    .loDivider = 0x00,
    .config.frontEndMode = 0x0,
    .config.biasMode = 0x0,
    .config.analogCfgMode = 0x0,
    .config.bNoFsPowerUp = 0x0,
    .txPower = 0x941E,
    .pRegOverrideCommon = rf_ble_overrides_common,
    .pRegOverride1Mbps = rf_ble_overrides_1mbps,
    .pRegOverride2Mbps = rf_ble_overrides_2mbps,
    .pRegOverrideCoded = rf_ble_overrides_coded,
};
/*---------------------------------------------------------------------------*/
// Structure for CMD_BLE5_ADV_AUX.pParams
rfc_ble5AdvAuxPar_t rf_ble5_adv_aux_par =
{
    .pRxQ = 0, // INSERT APPLICABLE POINTER: (dataQueue_t*)&xxx
    .rxConfig.bAutoFlushIgnored = 0x0,
    .rxConfig.bAutoFlushCrcErr = 0x0,
    .rxConfig.bAutoFlushEmpty = 0x0,
    .rxConfig.bIncludeLenByte = 0x0,
    .rxConfig.bIncludeCrc = 0x0,
    .rxConfig.bAppendRssi = 0x0,
    .rxConfig.bAppendStatus = 0x0,
    .rxConfig.bAppendTimestamp = 0x0,
    .advConfig.advFilterPolicy = 0x0,
    .advConfig.deviceAddrType = 0x0,
    .advConfig.targetAddrType = 0x0,
    .advConfig.bStrictLenFilter = 0x0,
    .advConfig.bDirected = 0x0,
    .advConfig.privIgnMode = 0x0,
    .advConfig.rpaMode = 0x0,
    .__dummy0 = 0x00,
    .auxPtrTargetType = 0x00,
    .auxPtrTargetTime = 0x00000000,
    .pAdvPkt = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .pRspPkt = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .pDeviceAddress = 0, // INSERT APPLICABLE POINTER: (uint16_t*)&xxx
    .pWhiteList = 0, // INSERT APPLICABLE POINTER: (uint32_t*)&xxx
};
/*---------------------------------------------------------------------------*/
// CMD_BLE5_ADV_AUX
// Bluetooth 5 Secondary Channel Advertiser Command
rfc_CMD_BLE5_ADV_AUX_t rf_cmd_ble5_adv_aux =
{
    .commandNo = 0x1824,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .startTime = 0x00000000,
    .startTrigger.triggerType = 0x0,
    .startTrigger.bEnaCmd = 0x0,
    .startTrigger.triggerNo = 0x0,
    .startTrigger.pastTrig = 0x0,
    .condition.rule = 0x1,
    .condition.nSkip = 0x0,
    .channel = 0x8C,
    .whitening.init = 0x51,
    .whitening.bOverride = 0x1,
    .phyMode.mainMode = 0x0,
    .phyMode.coding = 0x0,
    .rangeDelay = 0x00,
    .txPower = 0x0000,
    .pParams = &rf_ble5_adv_aux_par,
    .pOutput = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .tx20Power = 0x00000000,
};
/*---------------------------------------------------------------------------*/