/*
 * Copyright (c) 2018, Texas Instruments Incorporated - http://www.ti.com/
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. Neither the name of the copyright holder nor the names of its
 *    contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE
 * COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
 * OF THE POSSIBILITY OF SUCH DAMAGE.
 */
/*---------------------------------------------------------------------------*/
// Parameter summary
// Adv. Address: 010203040506
// Adv. Data: 255
// BLE Channel: 17
// Frequency: 2440 MHz
// PDU Payload length: 30
// TX Power: 9 dBm (requires define CCFG_FORCE_VDDR_HH = 1 in ccfg.c, see CC13xx/CC26xx Technical Reference Manual)
// Whitening: true
/*---------------------------------------------------------------------------*/
#include "sys/cc.h"
/*---------------------------------------------------------------------------*/
#include <ti/devices/DeviceFamily.h>
#include DeviceFamily_constructPath(driverlib/rf_mailbox.h)
#include DeviceFamily_constructPath(driverlib/rf_common_cmd.h)
#include DeviceFamily_constructPath(driverlib/rf_ble_cmd.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_ble.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_rfe_ble.h)

#include <ti/drivers/rf/RF.h>
/*---------------------------------------------------------------------------*/
#include "ble-settings.h"
/*---------------------------------------------------------------------------*/
// TI-RTOS RF Mode Object
RF_Mode RF_ble =
{
    .rfMode = RF_MODE_BLE,
    .cpePatchFxn = &rf_patch_cpe_ble,
    .mcePatchFxn = 0,
    .rfePatchFxn = &rf_patch_rfe_ble,
};
/*---------------------------------------------------------------------------*/
// TX Power table
// The RF_TxPowerTable_DEFAULT_PA_ENTRY macro is defined in RF.h and requires the following arguments:
// RF_TxPowerTable_DEFAULT_PA_ENTRY(bias, gain, boost coefficient)
// See the Technical Reference Manual for further details about the "txPower" Command field.
// The PA settings require the CCFG_FORCE_VDDR_HH = 0 unless stated otherwise.
RF_TxPowerTable_Entry txPowerTable[TX_POWER_TABLE_SIZE] =
{
    { -21, RF_TxPowerTable_DEFAULT_PA_ENTRY( 8, 3, 1,  6) },
    { -18, RF_TxPowerTable_DEFAULT_PA_ENTRY(11, 3, 1,  6) },
    { -15, RF_TxPowerTable_DEFAULT_PA_ENTRY(14, 3, 1, 10) },
    { -12, RF_TxPowerTable_DEFAULT_PA_ENTRY(20, 3, 1, 12) },
    {  -9, RF_TxPowerTable_DEFAULT_PA_ENTRY(26, 3, 1, 14) },
    {  -6, RF_TxPowerTable_DEFAULT_PA_ENTRY(35, 3, 1, 18) },
    {  -3, RF_TxPowerTable_DEFAULT_PA_ENTRY(47, 3, 1, 22) },
    {   0, RF_TxPowerTable_DEFAULT_PA_ENTRY(29, 0, 1, 45) },
    {   1, RF_TxPowerTable_DEFAULT_PA_ENTRY(33, 0, 1, 49) },
    {   2, RF_TxPowerTable_DEFAULT_PA_ENTRY(38, 0, 1, 55) },
    {   3, RF_TxPowerTable_DEFAULT_PA_ENTRY(44, 0, 1, 63) },
    {   4, RF_TxPowerTable_DEFAULT_PA_ENTRY(52, 0, 1, 59) },
    {   5, RF_TxPowerTable_DEFAULT_PA_ENTRY(60, 0, 1, 47) },
    {   6, RF_TxPowerTable_DEFAULT_PA_ENTRY(38, 0, 1, 49) }, // This setting requires CCFG_FORCE_VDDR_HH = 1.
    {   7, RF_TxPowerTable_DEFAULT_PA_ENTRY(46, 0, 1, 59) }, // This setting requires CCFG_FORCE_VDDR_HH = 1.
    {   8, RF_TxPowerTable_DEFAULT_PA_ENTRY(55, 0, 1, 51) }, // This setting requires CCFG_FORCE_VDDR_HH = 1.
    {   9, RF_TxPowerTable_DEFAULT_PA_ENTRY(63, 0, 1, 30) }, // This setting requires CCFG_FORCE_VDDR_HH = 1.
    RF_TxPowerTable_TERMINATION_ENTRY
};
/*---------------------------------------------------------------------------*/
// Overrides for CMD_RADIO_SETUP
uint32_t rf_ble_overrides[] CC_ALIGN(4) =
{
                                       // override_use_patch_ble_1mbps.xml
    MCE_RFE_OVERRIDE(0,0,0,1,0,0),     // PHY: Use MCE ROM, RFE RAM patch
                                       // override_synth_ble_1mbps.xml
    HW_REG_OVERRIDE(0x4038,0x0034),    // Synth: Set recommended RTRIM to 4
    (uint32_t)0x000784A3,              // Synth: Set Fref to 3.43 MHz
    HW_REG_OVERRIDE(0x4020,0x7F00),    // Synth: Configure fine calibration setting
    HW_REG_OVERRIDE(0x4064,0x0040),    // Synth: Configure fine calibration setting
    (uint32_t)0xB1070503,              // Synth: Configure fine calibration setting
    (uint32_t)0x05330523,              // Synth: Configure fine calibration setting
    (uint32_t)0xA47E0583,              // Synth: Set loop bandwidth after lock to 80 kHz
    (uint32_t)0xEAE00603,              // Synth: Set loop bandwidth after lock to 80 kHz
    (uint32_t)0x00010623,              // Synth: Set loop bandwidth after lock to 80 kHz
    HW32_ARRAY_OVERRIDE(0x405C,1),     // Synth: Configure PLL bias
    (uint32_t)0x18000000,              // Synth: Configure PLL bias
    ADI_REG_OVERRIDE(1,4,0x9F),        // Synth: Configure VCO LDO (in ADI1, set VCOLDOCFG=0x9F to use voltage input reference)
    ADI_HALFREG_OVERRIDE(1,7,0x4,0x4), // Synth: Configure synth LDO (in ADI1, set SLDOCTL0.COMP_CAP=1)
                                       // override_phy_ble_1mbps.xml
    (uint32_t)0x013800C3,              // Tx: Configure symbol shape for BLE frequency deviation requirements
    HW_REG_OVERRIDE(0x6088, 0x0045),   // Rx: Configure AGC reference level
    HW_REG_OVERRIDE(0x6084, 0x05FD),   // Rx: Configure AGC gain level
    (uint32_t)0x00038883,              // Rx: Configure LNA bias current trim offset
                                       // override_frontend_xd.xml
    (uint32_t)0x00F388A3,              // Rx: Set RSSI offset to adjust reported RSSI by +13 dB
                                       // TX power override
    ADI_REG_OVERRIDE(0,12,0xF8),       // Tx: Set PA trim to max (in ADI0, set PACTL0=0xF8)
    (uint32_t)0xFFFFFFFF,
};
/*---------------------------------------------------------------------------*/
// CMD_RADIO_SETUP
// Radio Setup Command for Pre-Defined Schemes
rfc_CMD_RADIO_SETUP_t rf_ble_cmd_radiosetup =
{
    .commandNo = 0x0802,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .startTime = 0x00000000,
    .startTrigger.triggerType = 0x0,
    .startTrigger.bEnaCmd = 0x0,
    .startTrigger.triggerNo = 0x0,
    .startTrigger.pastTrig = 0x0,
    .condition.rule = 0x1,
    .condition.nSkip = 0x0,
    .mode = 0x00,
    .loDivider = 0x00,
    .config.frontEndMode = 0x0,
    .config.biasMode = 0x1,
    .config.analogCfgMode = 0x0,
    .config.bNoFsPowerUp = 0x0,
    .txPower = 0x3D3F,
    .pRegOverride = rf_ble_overrides,
};
/*---------------------------------------------------------------------------*/
// CMD_FS
// Frequency Synthesizer Programming Command
rfc_CMD_FS_t rf_ble_cmd_fs =
{
    .commandNo = 0x0803,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .startTime = 0x00000000,
    .startTrigger.triggerType = 0x0,
    .startTrigger.bEnaCmd = 0x0,
    .startTrigger.triggerNo = 0x0,
    .startTrigger.pastTrig = 0x0,
    .condition.rule = 0x1,
    .condition.nSkip = 0x0,
    .frequency = 0x0988,
    .fractFreq = 0x0000,
    .synthConf.bTxMode = 0x0,
    .synthConf.refFreq = 0x0,
    .__dummy0 = 0x00,
    .__dummy1 = 0x00,
    .__dummy2 = 0x00,
    .__dummy3 = 0x0000,
};
/*---------------------------------------------------------------------------*/
// Structure for CMD_BLE_ADV_NC.pParams
rfc_bleAdvPar_t rf_ble_adv_par =
{
    .pRxQ = 0, // INSERT APPLICABLE POINTER: (dataQueue_t*)&xxx
    .rxConfig.bAutoFlushIgnored = 0x0,
    .rxConfig.bAutoFlushCrcErr = 0x0,
    .rxConfig.bAutoFlushEmpty = 0x0,
    .rxConfig.bIncludeLenByte = 0x0,
    .rxConfig.bIncludeCrc = 0x0,
    .rxConfig.bAppendRssi = 0x0,
    .rxConfig.bAppendStatus = 0x0,
    .rxConfig.bAppendTimestamp = 0x0,
    .advConfig.advFilterPolicy = 0x0,
    .advConfig.deviceAddrType = 0x0,
    .advConfig.peerAddrType = 0x0,
    .advConfig.bStrictLenFilter = 0x0,
    .advConfig.rpaMode = 0x0,
    .advLen = 0x18,
    .scanRspLen = 0x00,
    .pAdvData = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .pScanRspData = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .pDeviceAddress = 0, // INSERT APPLICABLE POINTER: (uint16_t*)&xxx
    .pWhiteList = 0, // INSERT APPLICABLE POINTER: (uint32_t*)&xxx
    .__dummy0 = 0x0000,
    .__dummy1 = 0x00,
    .endTrigger.triggerType = 0x1,
    .endTrigger.bEnaCmd = 0x0,
    .endTrigger.triggerNo = 0x0,
    .endTrigger.pastTrig = 0x0,
    .endTime = 0x00000000,
};
/*---------------------------------------------------------------------------*/
// CMD_BLE_ADV_NC
// BLE Non-Connectable Advertiser Command
rfc_CMD_BLE_ADV_NC_t rf_ble_cmd_ble_adv_nc =
{
    .commandNo = 0x1805,
    .status = 0x0000,
    .pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
    .startTime = 0x00000000,
    .startTrigger.triggerType = 0x0,
    .startTrigger.bEnaCmd = 0x0,
    .startTrigger.triggerNo = 0x0,
    .startTrigger.pastTrig = 0x0,
    .condition.rule = 0x1,
    .condition.nSkip = 0x0,
    .channel = 0x8C,
    .whitening.init = 0x51,
    .whitening.bOverride = 0x1,
    .pParams = &rf_ble_adv_par,
    .pOutput = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
};
/*---------------------------------------------------------------------------*/