/*
 * Copyright (c) 2018, Texas Instruments Incorporated - http://www.ti.com/
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. Neither the name of the copyright holder nor the names of its
 *    contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE
 * COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
 * OF THE POSSIBILITY OF SUCH DAMAGE.
 */
/*---------------------------------------------------------------------------*/
/*
 * Parameter summary
 * Address: 0
 * Address0: 0xAA
 * Address1: 0xBB
 * Frequency: 868.00000 MHz
 * Data Format: Serial mode disable
 * Deviation: 25.000 kHz
 * pktLen: 30
 * 802.15.4g Mode: 0
 * Select bit order to transmit PSDU octets:: 1
 * Packet Length Config: Variable
 * Max Packet Length: 255
 * Packet Length: 0
 * Packet Data: 255
 * RX Filter BW: 98 kHz
 * Symbol Rate: 50.00000 kBaud
 * Sync Word Length: 24 Bits
 * TX Power: 14 dBm (requires define CCFG_FORCE_VDDR_HH = 1 in ccfg.c,
 *                   see CC13xx/CC26xx Technical Reference Manual)
 * Whitening: Dynamically IEEE 802.15.4g compatible whitener and 16/32-bit CRC
 */
/*---------------------------------------------------------------------------*/
#include "contiki-conf.h"
#include "sys/cc.h"
/*---------------------------------------------------------------------------*/
#include <ti/devices/DeviceFamily.h>
#include DeviceFamily_constructPath(driverlib/rf_mailbox.h)
#include DeviceFamily_constructPath(driverlib/rf_common_cmd.h)
#include DeviceFamily_constructPath(driverlib/rf_prop_cmd.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_genfsk.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_rfe_genfsk.h)

#include <ti/drivers/rf/RF.h>
/*---------------------------------------------------------------------------*/
#include "prop-settings.h"
/*---------------------------------------------------------------------------*/
/* TI-RTOS RF Mode Object */
RF_Mode rf_prop_mode =
{
  .rfMode = RF_MODE_MULTIPLE,
  .cpePatchFxn = &rf_patch_cpe_genfsk,
  .mcePatchFxn = 0,
  .rfePatchFxn = &rf_patch_rfe_genfsk,
};
/*---------------------------------------------------------------------------*/
#if defined(DEVICE_CC1310)
/*
 * CMD_PROP_RADIO_DIV_SETUP must be configured with default TX power value
 * in the .txPower field. This depends on whether RF_CONF_TXPOWER_BOOST_MODE
 * is configured or not.
 */
#if RF_CONF_TXPOWER_BOOST_MODE
#define DEFAULT_TX_POWER    0xA73F /* 14 dBm */
#else
#define DEFAULT_TX_POWER    0xA63F /* 12.5 dBm (rounded up to 13 dBm) */
#endif

#endif /* defined(DEVICE_CC1310) */
/*---------------------------------------------------------------------------*/
#if defined(DEVICE_CC1350)
/*
 * CMD_PROP_RADIO_DIV_SETUP must be configured with default TX power value
 * in the .txPower field. This depends on whether RF_CONF_TXPOWER_BOOST_MODE
 * is configured or not.
 */
#if RF_CONF_TXPOWER_BOOST_MODE
#define DEFAULT_TX_POWER    0xAB3F /* 14 dBm */
#else
#define DEFAULT_TX_POWER    0xBC2B /* 12 dBm */
#endif

#endif /* defined(DEVICE_CC1350) */
    /*---------------------------------------------------------------------------*/
#if defined(DEVICE_CC1350_4)
/*
 * CMD_PROP_RADIO_DIV_SETUP must be configured with default TX power value
 * in the .txPower field. This depends on whether RF_CONF_TXPOWER_BOOST_MODE
 * is configured or not.
 */
#if RF_CONF_TXPOWER_BOOST_MODE
#define DEFAULT_TX_POWER    0x913F /* 15 dBm */
#else
#define DEFAULT_TX_POWER    0xB83F /* 13.7 dBm (rounded up to 14 dBm) */
#endif

#endif /* defined(DEVICE_CC1350_4) */
/*---------------------------------------------------------------------------*/
/* Overrides for CMD_PROP_RADIO_DIV_SETUP */
uint32_t rf_prop_overrides[] CC_ALIGN(4) =
{
                                      /* override_use_patch_prop_genfsk.xml */
  MCE_RFE_OVERRIDE(0,4,0,1,0,0),      /* PHY: Use MCE ROM bank 4, RFE RAM patch */
                                      /* override_synth_prop_863_930_div5.xml */
  HW_REG_OVERRIDE(0x4038,0x0037),     /* Synth: Set recommended RTRIM to 7 */
  (uint32_t)0x000684A3,               /* Synth: Set Fref to 4 MHz */
  HW_REG_OVERRIDE(0x4020,0x7F00),     /* Synth: Configure fine calibration setting */
  HW_REG_OVERRIDE(0x4064,0x0040),     /* Synth: Configure fine calibration setting */
  (uint32_t)0xB1070503,               /* Synth: Configure fine calibration setting */
  (uint32_t)0x05330523,               /* Synth: Configure fine calibration setting */
  (uint32_t)0x0A480583,               /* Synth: Set loop bandwidth after lock to 20 kHz */
  (uint32_t)0x7AB80603,               /* Synth: Set loop bandwidth after lock to 20 kHz */
                                      /* Synth: Configure VCO LDO */
  ADI_REG_OVERRIDE(1,4,0x9F),         /* (in ADI1, set VCOLDOCFG=0x9F to use voltage input reference) */
  ADI_HALFREG_OVERRIDE(1,7,0x4,0x4),  /* Synth: Configure synth LDO (in ADI1, set SLDOCTL0.COMP_CAP=1) */
  (uint32_t)0x02010403,               /* Synth: Use 24 MHz XOSC as synth clock, enable extra PLL filtering */
  (uint32_t)0x00108463,               /* Synth: Configure extra PLL filtering */
  (uint32_t)0x04B00243,               /* Synth: Increase synth programming timeout (0x04B0 RAT ticks = 300 us) */
                                      /* override_phy_rx_aaf_bw_0xd.xml */
                                      /* Rx: Set anti-aliasing filter bandwidth to 0xD */
  ADI_HALFREG_OVERRIDE(0,61,0xF,0xD), /* (in ADI0, set IFAMPCTL3[7:4]=0xD) */
                                      /* override_phy_gfsk_rx.xml */
  (uint32_t)0x00038883,               /* Rx: Set LNA bias current trim offset to 3 */
  HW_REG_OVERRIDE(0x6084,0x35F1),     /* Rx: Freeze RSSI on sync found event */
                                      /* override_phy_gfsk_pa_ramp_agc_reflevel_0x1a.xml */
                                      /* Tx: Configure PA ramping setting (0x41). */
  HW_REG_OVERRIDE(0x6088,0x411A),     /* Rx: Set AGC reference level to 0x1A. */
  HW_REG_OVERRIDE(0x608C,0x8213),     /* Tx: Configure PA ramping setting */
                                      /* override_crc_ieee_802_15_4.xml */
                                      /* IEEE 802.15.4g: Fix incorrect initialization value for */
  (uint32_t)0x00000943,               /* CRC-16 calculation (see TRM section 23.7.5.2.1) */
                                      /* IEEE 802.15.4g: Fix incorrect initialization value for */
  (uint32_t)0x00000963,               /* CRC-16 calculation (see TRM section 23.7.5.2.1) */
#if defined(DEVICE_CC1350_4)
                                      /* override_phy_rx_rssi_offset_neg2db.xml */
  (uint32_t)0x000288A3,               /* Rx: Set RSSI offset to adjust reported RSSI by -2 dB */
#else
                                      /* override_phy_rx_rssi_offset_5db.xml */
  (uint32_t)0x00FB88A3,               /* Rx: Set RSSI offset to adjust reported RSSI by +5 dB */
#endif
                                      /* TX power override */
#if RF_CONF_TXPOWER_BOOST_MODE
  ADI_REG_OVERRIDE(0,12,0xF8),        /* Tx: Set PA trim to max (in ADI0, set PACTL0=0xF8) */
#endif
  (uint32_t)0xFFFFFFFF,
};
/*---------------------------------------------------------------------------*/
/* CMD_PROP_RADIO_DIV_SETUP */
/* Proprietary Mode Radio Setup Command for All Frequency Bands */
rfc_CMD_PROP_RADIO_DIV_SETUP_t rf_cmd_prop_radio_div_setup =
{
  .commandNo = CMD_PROP_RADIO_DIV_SETUP,
  .status = IDLE,
  .pNextOp = 0,
  .startTime = 0x00000000,
  .startTrigger.triggerType = TRIG_NOW,
  .startTrigger.bEnaCmd = 0x0,
  .startTrigger.triggerNo = 0x0,
  .startTrigger.pastTrig = 0x0,
  .condition.rule = COND_NEVER,
  .condition.nSkip = 0x0,
  .modulation.modType = 0x1,
  .modulation.deviation = 0x64,
  .symbolRate.preScale = 0xF,
  .symbolRate.rateWord = 0x8000,
  .rxBw = 0x24,
  .preamConf.nPreamBytes = 0x7,
  .preamConf.preamMode = 0x0,
  .formatConf.nSwBits = 0x18,
  .formatConf.bBitReversal = 0x0,
  .formatConf.bMsbFirst = 0x1,
  .formatConf.fecMode = 0x0,
  .formatConf.whitenMode = 0x7,
  .config.frontEndMode = 0x0, /* set by driver */
  .config.biasMode = 0x0, /* set by driver */
  .config.analogCfgMode = 0x0,
  .config.bNoFsPowerUp = 0x0,
  .txPower = DEFAULT_TX_POWER,
  .pRegOverride = rf_prop_overrides,
  .centerFreq = 0x0364, /* set by driver */
  .intFreq = 0x8000, /* set by driver */
  .loDivider = 0x05, /* set by driver */
};
/*---------------------------------------------------------------------------*/
/* CMD_FS */
/* Frequency Synthesizer Programming Command */
rfc_CMD_FS_t rf_cmd_prop_fs =
{
  .commandNo = CMD_FS,
  .status = IDLE,
  .pNextOp = 0,
  .startTime = 0x00000000,
  .startTrigger.triggerType = TRIG_NOW,
  .startTrigger.bEnaCmd = 0x0,
  .startTrigger.triggerNo = 0x0,
  .startTrigger.pastTrig = 0x0,
  .condition.rule = COND_NEVER,
  .condition.nSkip = 0x0,
  .frequency = 0x0364, /* set by driver */
  .fractFreq = 0x0000, /* set by driver */
  .synthConf.bTxMode = 0x0,
  .synthConf.refFreq = 0x0,
  .__dummy0 = 0x00,
  .__dummy1 = 0x00,
  .__dummy2 = 0x00,
  .__dummy3 = 0x0000,
};
/*---------------------------------------------------------------------------*/
/* CMD_PROP_TX_ADV */
/* Proprietary Mode Advanced Transmit Command */
rfc_CMD_PROP_TX_ADV_t rf_cmd_prop_tx_adv =
{
  .commandNo = CMD_PROP_TX_ADV,
  .status = IDLE,
  .pNextOp = 0,
  .startTime = 0x00000000,
  .startTrigger.triggerType = TRIG_NOW,
  .startTrigger.bEnaCmd = 0x0,
  .startTrigger.triggerNo = 0x0,
  .startTrigger.pastTrig = 0x0,
  .condition.rule = COND_NEVER,
  .condition.nSkip = 0x0,
  .pktConf.bFsOff = 0x0,
  .pktConf.bUseCrc = 0x1,
  .pktConf.bCrcIncSw = 0x0,
  .pktConf.bCrcIncHdr = 0x0,
  .numHdrBits = 0x10,
  .pktLen = 0x0, /* set by driver */
  .startConf.bExtTxTrig = 0x0,
  .startConf.inputMode = 0x0,
  .startConf.source = 0x0,
  .preTrigger.triggerType = TRIG_REL_START,
  .preTrigger.bEnaCmd = 0x0,
  .preTrigger.triggerNo = 0x0,
  .preTrigger.pastTrig = 0x1,
  .preTime = 0x00000000,
  .syncWord = 0x0055904E,
  .pPkt = 0, /* set by driver */
};
/*---------------------------------------------------------------------------*/
/* CMD_PROP_RX_ADV */
/* Proprietary Mode Advanced Receive Command */
rfc_CMD_PROP_RX_ADV_t rf_cmd_prop_rx_adv =
{
  .commandNo = CMD_PROP_RX_ADV,
  .status = IDLE,
  .pNextOp = 0,
  .startTime = 0x00000000,
  .startTrigger.triggerType = TRIG_NOW,
  .startTrigger.bEnaCmd = 0x0,
  .startTrigger.triggerNo = 0x0,
  .startTrigger.pastTrig = 0x0,
  .condition.rule = COND_NEVER,
  .condition.nSkip = 0x0,
  .pktConf.bFsOff = 0x0,
  .pktConf.bRepeatOk = 0x1,
  .pktConf.bRepeatNok = 0x1,
  .pktConf.bUseCrc = 0x1,
  .pktConf.bCrcIncSw = 0x0,
  .pktConf.bCrcIncHdr = 0x0,
  .pktConf.endType = 0x0,
  .pktConf.filterOp = 0x1,
  .rxConf.bAutoFlushIgnored = 0x1,
  .rxConf.bAutoFlushCrcErr = 0x1,
  .rxConf.bIncludeHdr = 0x0,
  .rxConf.bIncludeCrc = 0x0,
  .rxConf.bAppendRssi = 0x1,
  .rxConf.bAppendTimestamp = 0x0,
  .rxConf.bAppendStatus = 0x1,
  .syncWord0 = 0x0055904E,
  .syncWord1 = 0x00000000,
  .maxPktLen = 0x0, /* set by driver */
  .hdrConf.numHdrBits = 0x10,
  .hdrConf.lenPos = 0x0,
  .hdrConf.numLenBits = 0x0B,
  .addrConf.addrType = 0x0,
  .addrConf.addrSize = 0x0,
  .addrConf.addrPos = 0x0,
  .addrConf.numAddr = 0x0,
  .lenOffset = 0xFC,
  .endTrigger.triggerType = TRIG_NEVER,
  .endTrigger.bEnaCmd = 0x0,
  .endTrigger.triggerNo = 0x0,
  .endTrigger.pastTrig = 0x0,
  .endTime = 0x00000000,
  .pAddr = 0, /* set by driver */
  .pQueue = 0, /* set by driver */
  .pOutput = 0, /* set by driver */
};
/*---------------------------------------------------------------------------*/