/* * Copyright (c) 2018, Texas Instruments Incorporated - http://www.ti.com/ * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. Neither the name of the copyright holder nor the names of its * contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED * OF THE POSSIBILITY OF SUCH DAMAGE. */ /*---------------------------------------------------------------------------*/ /* * Parameter summary * Adv. Address: 010203040506 * Adv. Data: dummy * BLE Channel: 17 * Extended Header: 09 09 010203040506 babe * Frequency: 2440 MHz * PDU Payload length:: 30 * TX Power: 5 dBm (requires define CCFG_FORCE_VDDR_HH = 0 in ccfg * see CC13xx/CC26xx Technical Reference Manual) * Whitening: true */ /*---------------------------------------------------------------------------*/ #include "sys/cc.h" /*---------------------------------------------------------------------------*/ #include #include DeviceFamily_constructPath(driverlib/rf_mailbox.h) #include DeviceFamily_constructPath(driverlib/rf_common_cmd.h) #include DeviceFamily_constructPath(driverlib/rf_ble_cmd.h) #include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_bt5.h) #include DeviceFamily_constructPath(rf_patches/rf_patch_rfe_bt5.h) #include DeviceFamily_constructPath(rf_patches/rf_patch_mce_bt5.h) #include /*---------------------------------------------------------------------------*/ #include "ble-settings.h" /*---------------------------------------------------------------------------*/ /* TI-RTOS RF Mode Object */ RF_Mode rf_ble_mode = { .rfMode = RF_MODE_AUTO, .cpePatchFxn = &rf_patch_cpe_bt5, .mcePatchFxn = &rf_patch_mce_bt5, .rfePatchFxn = &rf_patch_rfe_bt5, }; /*---------------------------------------------------------------------------*/ /* * TX Power table * The RF_TxPowerTable_DEFAULT_PA_ENTRY macro is defined in RF.h and requires the following arguments: * RF_TxPowerTable_DEFAULT_PA_ENTRY(bias, gain, boost coefficient) * See the Technical Reference Manual for further details about the "txPower" Command field. * The PA settings require the CCFG_FORCE_VDDR_HH = 0 unless stated otherwise. */ RF_TxPowerTable_Entry rf_ble_tx_power_table[RF_BLE_TX_POWER_TABLE_SIZE+1] = { { -21, RF_TxPowerTable_DEFAULT_PA_ENTRY( 7, 3, 0, 3) }, { -18, RF_TxPowerTable_DEFAULT_PA_ENTRY( 9, 3, 0, 3) }, { -15, RF_TxPowerTable_DEFAULT_PA_ENTRY( 8, 2, 0, 6) }, { -12, RF_TxPowerTable_DEFAULT_PA_ENTRY(10, 2, 0, 8) }, { -10, RF_TxPowerTable_DEFAULT_PA_ENTRY(12, 2, 0, 11) }, { -9, RF_TxPowerTable_DEFAULT_PA_ENTRY(13, 2, 0, 5) }, { -6, RF_TxPowerTable_DEFAULT_PA_ENTRY(13, 1, 0, 16) }, { -5, RF_TxPowerTable_DEFAULT_PA_ENTRY(14, 1, 0, 17) }, { -3, RF_TxPowerTable_DEFAULT_PA_ENTRY(17, 1, 0, 20) }, { 0, RF_TxPowerTable_DEFAULT_PA_ENTRY(25, 1, 0, 26) }, { 1, RF_TxPowerTable_DEFAULT_PA_ENTRY(28, 1, 0, 28) }, { 2, RF_TxPowerTable_DEFAULT_PA_ENTRY(13, 0, 0, 34) }, { 3, RF_TxPowerTable_DEFAULT_PA_ENTRY(17, 0, 0, 42) }, { 4, RF_TxPowerTable_DEFAULT_PA_ENTRY(22, 0, 0, 54) }, { 5, RF_TxPowerTable_DEFAULT_PA_ENTRY(30, 0, 0, 74) }, RF_TxPowerTable_TERMINATION_ENTRY }; /*---------------------------------------------------------------------------*/ /* Overrides for CMD_BLE5_RADIO_SETUP */ uint32_t rf_ble_overrides_common[] CC_ALIGN(4) = { /* override_ble5_setup_override_common.xml */ (uint32_t)0x02400403, /* Synth: Use 48 MHz crystal, enable extra PLL filtering */ (uint32_t)0x001C8473, /* Synth: Configure extra PLL filtering */ (uint32_t)0x00088433, /* Synth: Configure synth hardware */ (uint32_t)0x00038793, /* Synth: Set minimum RTRIM to 3 */ HW32_ARRAY_OVERRIDE(0x4004,1), /* Synth: Configure faster calibration */ (uint32_t)0x1C0C0618, /* Synth: Configure faster calibration */ (uint32_t)0xC00401A1, /* Synth: Configure faster calibration */ (uint32_t)0x00010101, /* Synth: Configure faster calibration */ (uint32_t)0xC0040141, /* Synth: Configure faster calibration */ (uint32_t)0x00214AD3, /* Synth: Configure faster calibration */ (uint32_t)0x02980243, /* Synth: Decrease synth programming time-out (0x0298 RAT ticks = 166 us) */ /* DC/DC regulator: In Tx, use DCDCCTL5[3:0]=0xC (DITHER_EN=1 and IPEAK=4). */ (uint32_t)0xFCFC08C3, /* In Rx, use DCDCCTL5[3:0]=0xC (DITHER_EN=1 and IPEAK=4). */ (uint32_t)0x00038883, /* Rx: Set LNA bias current offset to adjust +3 (default: 0) */ (uint32_t)0x000288A3, /* Rx: Set RSSI offset to adjust reported RSSI by -2 dB (default: 0) */ (uint32_t)0x01080263, /* Bluetooth 5: Compensate for reduced pilot tone length */ (uint32_t)0x08E90AA3, /* Bluetooth 5: Compensate for reduced pilot tone length */ (uint32_t)0x00068BA3, /* Bluetooth 5: Compensate for reduced pilot tone length */ /* Bluetooth 5: Set correct total clock accuracy for received AuxPtr */ (uint32_t)0x0E490C83, /* assuming local sleep clock of 50 ppm */ (uint32_t)0xFFFFFFFF, }; /*---------------------------------------------------------------------------*/ /* Overrides for CMD_BLE5_RADIO_SETUP */ uint32_t rf_ble_overrides_1mbps[] CC_ALIGN(4) = { /* override_ble5_setup_override_1mbps.xml */ MCE_RFE_OVERRIDE(1,0,0,1,0,0), /* PHY: Use MCE RAM patch (mode 0), RFE RAM patch (mode 0) */ HW_REG_OVERRIDE(0x5320,0x0240), /* Bluetooth 5: Reduce pilot tone length */ (uint32_t)0x013302A3, /* Bluetooth 5: Compensate for reduced pilot tone length */ (uint32_t)0xFFFFFFFF, }; /*---------------------------------------------------------------------------*/ /* Overrides for CMD_BLE5_RADIO_SETUP */ uint32_t rf_ble_overrides_2mbps[] CC_ALIGN(4) = { /* override_ble5_setup_override_2mbps.xml */ MCE_RFE_OVERRIDE(1,0,2,1,0,2), /* PHY: Use MCE RAM patch (mode 2), RFE RAM patch (mode 2) */ HW_REG_OVERRIDE(0x5320,0x0240), /* Bluetooth 5: Reduce pilot tone length */ (uint32_t)0x00D102A3, /* Bluetooth 5: Compensate for reduced pilot tone length */ (uint32_t)0xFFFFFFFF, }; /*---------------------------------------------------------------------------*/ /* Overrides for CMD_BLE5_RADIO_SETUP */ uint32_t rf_ble_overrides_coded[] CC_ALIGN(4) = { /* override_ble5_setup_override_coded.xml */ MCE_RFE_OVERRIDE(1,0,1,1,0,1), /* PHY: Use MCE RAM patch (mode 1), RFE RAM patch (mode 1) */ HW_REG_OVERRIDE(0x5320,0x0240), /* Bluetooth 5: Reduce pilot tone length */ (uint32_t)0x078902A3, /* Bluetooth 5: Compensate for reduced pilot tone length */ (uint32_t)0xFFFFFFFF, }; /*---------------------------------------------------------------------------*/ /* CMD_BLE5_RADIO_SETUP: Bluetooth 5 Radio Setup Command for all PHYs */ rfc_CMD_BLE5_RADIO_SETUP_t rf_cmd_ble5_radio_setup = { .commandNo = CMD_BLE5_RADIO_SETUP, .status = IDLE, .pNextOp = 0, .startTime = 0x00000000, .startTrigger.triggerType = TRIG_NOW, .startTrigger.bEnaCmd = 0x0, .startTrigger.triggerNo = 0x0, .startTrigger.pastTrig = 0x0, .condition.rule = COND_NEVER, .condition.nSkip = 0x0, .defaultPhy.mainMode = 0x0, .defaultPhy.coding = 0x0, .loDivider = 0x00, .config.frontEndMode = 0x0, .config.biasMode = 0x0, .config.analogCfgMode = 0x0, .config.bNoFsPowerUp = 0x0, .txPower = 0x941E, .pRegOverrideCommon = rf_ble_overrides_common, .pRegOverride1Mbps = rf_ble_overrides_1mbps, .pRegOverride2Mbps = rf_ble_overrides_2mbps, .pRegOverrideCoded = rf_ble_overrides_coded, }; /*---------------------------------------------------------------------------*/ /* Structure for CMD_BLE5_ADV_AUX.pParams */ rfc_ble5AdvAuxPar_t rf_ble5_adv_aux_par = { .pRxQ = 0, .rxConfig.bAutoFlushIgnored = 0x0, .rxConfig.bAutoFlushCrcErr = 0x0, .rxConfig.bAutoFlushEmpty = 0x0, .rxConfig.bIncludeLenByte = 0x0, .rxConfig.bIncludeCrc = 0x0, .rxConfig.bAppendRssi = 0x0, .rxConfig.bAppendStatus = 0x0, .rxConfig.bAppendTimestamp = 0x0, .advConfig.advFilterPolicy = 0x0, .advConfig.deviceAddrType = 0x0, .advConfig.targetAddrType = 0x0, .advConfig.bStrictLenFilter = 0x0, .advConfig.bDirected = 0x0, .advConfig.privIgnMode = 0x0, .advConfig.rpaMode = 0x0, .__dummy0 = 0x00, .auxPtrTargetType = 0x00, .auxPtrTargetTime = 0x00000000, .pAdvPkt = 0, .pRspPkt = 0, .pDeviceAddress = 0, .pWhiteList = 0, }; /*---------------------------------------------------------------------------*/ /* CMD_BLE5_ADV_AUX: Bluetooth 5 Secondary Channel Advertiser Command */ rfc_CMD_BLE5_ADV_AUX_t rf_cmd_ble5_adv_aux = { .commandNo = CMD_BLE5_ADV_AUX, .status = IDLE, .pNextOp = 0, .startTime = 0x00000000, .startTrigger.triggerType = TRIG_NOW, .startTrigger.bEnaCmd = 0x0, .startTrigger.triggerNo = 0x0, .startTrigger.pastTrig = 0x0, .condition.rule = COND_NEVER, .condition.nSkip = 0x0, .channel = 0x8C, .whitening.init = 0x51, .whitening.bOverride = 0x1, .phyMode.mainMode = 0x0, .phyMode.coding = 0x0, .rangeDelay = 0x00, .txPower = 0x0000, .pParams = &rf_ble5_adv_aux_par, .pOutput = 0, .tx20Power = 0x00000000, }; /*---------------------------------------------------------------------------*/