/** * \addtogroup cc2538dk * @{ * * \file * Configuration for the cc2538dk platform */ #ifndef CONTIKI_CONF_H_ #define CONTIKI_CONF_H_ #include #include /*---------------------------------------------------------------------------*/ /* Include Project Specific conf */ #ifdef PROJECT_CONF_H #include PROJECT_CONF_H #endif /* PROJECT_CONF_H */ /*---------------------------------------------------------------------------*/ /** * \name Compiler configuration and platform-specific type definitions * * Those values are not meant to be modified by the user * @{ */ #define CLOCK_CONF_SECOND 128 /* Compiler configurations */ #define CCIF #define CLIF /* Platform typedefs */ typedef uint32_t clock_time_t; typedef uint32_t uip_stats_t; /* * rtimer.h typedefs rtimer_clock_t as unsigned short. We need to define * RTIMER_CLOCK_LT to override this */ typedef uint32_t rtimer_clock_t; #define RTIMER_CLOCK_LT(a,b) ((int32_t)((a)-(b)) < 0) /** @} */ /*---------------------------------------------------------------------------*/ /** * \name Serial Boot Loader Backdoor configuration * * @{ */ #ifndef FLASH_CCA_CONF_BOOTLDR_BACKDOOR #define FLASH_CCA_CONF_BOOTLDR_BACKDOOR 1 /** RAM DMA channel */ #define USB_ARCH_CONF_TX_DMA_CHAN 1 /**< RAM -> USB DMA channel */ #define CC2538_RF_CONF_TX_DMA_CHAN 2 /**< RF -> RAM DMA channel */ #define CC2538_RF_CONF_RX_DMA_CHAN 3 /**< RAM -> RF DMA channel */ #define UDMA_CONF_MAX_CHANNEL CC2538_RF_CONF_RX_DMA_CHAN /** @} */ /*---------------------------------------------------------------------------*/ /** * \name Character I/O Configuration * * @{ */ #ifndef UART_CONF_ENABLE #define UART_CONF_ENABLE 1 /**< Enable/Disable UART I/O */ #endif #ifndef UART0_CONF_BAUD_RATE #define UART0_CONF_BAUD_RATE 115200 /**< Default UART0 baud rate */ #endif #ifndef UART1_CONF_BAUD_RATE #define UART1_CONF_BAUD_RATE 115200 /**< Default UART1 baud rate */ #endif #ifndef SLIP_ARCH_CONF_USB #define SLIP_ARCH_CONF_USB 0 /**< SLIP over UART by default */ #endif #ifndef CC2538_RF_CONF_SNIFFER_USB #define CC2538_RF_CONF_SNIFFER_USB 0 /**< Sniffer out over UART by default */ #endif #ifndef DBG_CONF_USB #define DBG_CONF_USB 0 /**< All debugging over UART by default */ #endif #ifndef SERIAL_LINE_CONF_UART #define SERIAL_LINE_CONF_UART 0 /**< UART to use with serial line */ #endif #if !SLIP_ARCH_CONF_USB #ifndef SLIP_ARCH_CONF_UART #define SLIP_ARCH_CONF_UART 0 /**< UART to use with SLIP */ #endif #endif #if !CC2538_RF_CONF_SNIFFER_USB #ifndef CC2538_RF_CONF_SNIFFER_UART #define CC2538_RF_CONF_SNIFFER_UART 0 /**< UART to use with sniffer */ #endif #endif #if !DBG_CONF_USB #ifndef DBG_CONF_UART #define DBG_CONF_UART 0 /**< UART to use for debugging */ #endif #endif #ifndef UART1_CONF_UART #define UART1_CONF_UART 0 /**< UART to use for examples relying on the uart1_* API */ #endif /* Turn off example-provided putchars */ #define SLIP_BRIDGE_CONF_NO_PUTCHAR 1 #define SLIP_RADIO_CONF_NO_PUTCHAR 1 #ifndef SLIP_ARCH_CONF_ENABLED /* * Determine whether we need SLIP * This will keep working while UIP_FALLBACK_INTERFACE and CMD_CONF_OUTPUT * keep using SLIP */ #if defined (UIP_FALLBACK_INTERFACE) || defined (CMD_CONF_OUTPUT) #define SLIP_ARCH_CONF_ENABLED 1 #endif #endif /* * When set, the radio turns off address filtering and sends all captured * frames down a peripheral (UART or USB, depending on the value of * CC2538_RF_CONF_SNIFFER_USB) */ #ifndef CC2538_RF_CONF_SNIFFER #define CC2538_RF_CONF_SNIFFER 0 #endif /** * \brief Define this as 1 to build a headless node. * * The UART will not be initialised its clock will be gated, offering some * energy savings. The USB will not be initialised either */ #ifndef CC2538_CONF_QUIET #define CC2538_CONF_QUIET 0 #endif /* CC2538_CONF_QUIET is hard and overrides all other related defines */ #if CC2538_CONF_QUIET #undef USB_SERIAL_CONF_ENABLE #define USB_SERIAL_CONF_ENABLE 0 #undef UART_CONF_ENABLE #define UART_CONF_ENABLE 0 #undef STARTUP_CONF_VERBOSE #define STARTUP_CONF_VERBOSE 0 /* Little sanity check: We can't have quiet sniffers */ #if CC2538_RF_CONF_SNIFFER #error "CC2538_RF_CONF_SNIFFER == 1 and CC2538_CONF_QUIET == 1" #error "These values are conflicting. Please set either to 0" #endif #endif /* CC2538_CONF_QUIET */ /** * \brief Enable the USB core only if we need it */ #ifndef USB_SERIAL_CONF_ENABLE #define USB_SERIAL_CONF_ENABLE \ ((SLIP_ARCH_CONF_USB & SLIP_ARCH_CONF_ENABLED) | \ DBG_CONF_USB | \ (CC2538_RF_CONF_SNIFFER & CC2538_RF_CONF_SNIFFER_USB)) #endif /* * If debugging and SLIP use the same peripheral, this will be 1. Don't modify * this */ #if SLIP_ARCH_CONF_ENABLED #define DBG_CONF_SLIP_MUX (SLIP_ARCH_CONF_USB == DBG_CONF_USB && \ (SLIP_ARCH_CONF_USB || \ SLIP_ARCH_CONF_UART == DBG_CONF_UART)) #endif /* * Automatic detection of whether a specific UART is in use */ #define UART_IN_USE_BY_SERIAL_LINE(u) (SERIAL_LINE_CONF_UART == (u)) #define UART_IN_USE_BY_SLIP(u) (SLIP_ARCH_CONF_ENABLED && \ !SLIP_ARCH_CONF_USB && \ SLIP_ARCH_CONF_UART == (u)) #define UART_IN_USE_BY_RF_SNIFFER(u) (CC2538_RF_CONF_SNIFFER && \ !CC2538_RF_CONF_SNIFFER_USB && \ CC2538_RF_CONF_SNIFFER_UART == (u)) #define UART_IN_USE_BY_DBG(u) (!DBG_CONF_USB && DBG_CONF_UART == (u)) #define UART_IN_USE_BY_UART1(u) (UART1_CONF_UART == (u)) #define UART_IN_USE(u) ( \ UART_CONF_ENABLE && \ (UART_IN_USE_BY_SERIAL_LINE(u) || \ UART_IN_USE_BY_SLIP(u) || \ UART_IN_USE_BY_RF_SNIFFER(u) || \ UART_IN_USE_BY_DBG(u) || \ UART_IN_USE_BY_UART1(u)) \ ) /** @} */ /*---------------------------------------------------------------------------*/ /* board.h assumes that basic configuration is done */ #include "board.h" /*---------------------------------------------------------------------------*/ /** * \name Network Stack Configuration * * @{ */ #ifndef NETSTACK_CONF_NETWORK #if NETSTACK_CONF_WITH_IPV6 #define NETSTACK_CONF_NETWORK sicslowpan_driver #else #define NETSTACK_CONF_NETWORK rime_driver #endif /* NETSTACK_CONF_WITH_IPV6 */ #endif /* NETSTACK_CONF_NETWORK */ #ifndef NETSTACK_CONF_MAC #define NETSTACK_CONF_MAC csma_driver #endif #ifndef NETSTACK_CONF_RDC #define NETSTACK_CONF_RDC contikimac_driver #endif /* Configure NullRDC for when it's selected */ #define NULLRDC_802154_AUTOACK 1 #define NULLRDC_802154_AUTOACK_HW 1 /* Configure ContikiMAC for when it's selected */ #define CONTIKIMAC_CONF_WITH_PHASE_OPTIMIZATION 0 #define WITH_FAST_SLEEP 1 #ifndef NETSTACK_CONF_RDC_CHANNEL_CHECK_RATE #define NETSTACK_CONF_RDC_CHANNEL_CHECK_RATE 8 #endif #ifndef NETSTACK_CONF_FRAMER #if NETSTACK_CONF_WITH_IPV6 #define NETSTACK_CONF_FRAMER framer_802154 #else /* NETSTACK_CONF_WITH_IPV6 */ #define NETSTACK_CONF_FRAMER contikimac_framer #endif /* NETSTACK_CONF_WITH_IPV6 */ #endif /* NETSTACK_CONF_FRAMER */ #define NETSTACK_CONF_RADIO cc2538_rf_driver /** @} */ /*---------------------------------------------------------------------------*/ /** * \name LPM configuration * @{ */ #ifndef LPM_CONF_ENABLE #define LPM_CONF_ENABLE 1 /**< Set to 0 to disable LPM entirely */ #endif /** * \brief Maximum PM * * The SoC will never drop to a Power Mode deeper than the one specified here. * 0 for PM0, 1 for PM1 and 2 for PM2 */ #ifndef LPM_CONF_MAX_PM #define LPM_CONF_MAX_PM 1 #endif #ifndef LPM_CONF_STATS #define LPM_CONF_STATS 0 /**< Set to 1 to enable LPM-related stats */ #endif /** @} */ /*---------------------------------------------------------------------------*/ /** * \name IEEE address configuration * * Used to generate our RIME & IPv6 address * @{ */ /** * \brief Location of the IEEE address * 0 => Read from InfoPage, * 1 => Use a hardcoded address, configured by IEEE_ADDR_CONF_ADDRESS */ #ifndef IEEE_ADDR_CONF_HARDCODED #define IEEE_ADDR_CONF_HARDCODED 0 #endif /** * \brief The hardcoded IEEE address to be used when IEEE_ADDR_CONF_HARDCODED * is defined as 1 */ #ifndef IEEE_ADDR_CONF_ADDRESS #define IEEE_ADDR_CONF_ADDRESS { 0x00, 0x12, 0x4B, 0x00, 0x89, 0xAB, 0xCD, 0xEF } #endif /** * \brief Location of the IEEE address in the InfoPage when * IEEE_ADDR_CONF_HARDCODED is defined as 0 * 0 => Use the primary address location * 1 => Use the secondary address location */ #ifndef IEEE_ADDR_CONF_USE_SECONDARY_LOCATION #define IEEE_ADDR_CONF_USE_SECONDARY_LOCATION 0 #endif /** @} */ /*---------------------------------------------------------------------------*/ /** * \name RF configuration * * @{ */ /* RF Config */ #ifndef IEEE802154_CONF_PANID #define IEEE802154_CONF_PANID 0xABCD #endif #ifndef CC2538_RF_CONF_CHANNEL #define CC2538_RF_CONF_CHANNEL 25 #endif /* CC2538_RF_CONF_CHANNEL */ #ifndef CC2538_RF_CONF_AUTOACK #define CC2538_RF_CONF_AUTOACK 1 /**< RF H/W generates ACKs */ #endif /* CC2538_CONF_AUTOACK */ #ifndef CC2538_RF_CONF_TX_USE_DMA #define CC2538_RF_CONF_TX_USE_DMA 1 /**< RF TX over DMA */ #endif #ifndef CC2538_RF_CONF_RX_USE_DMA #define CC2538_RF_CONF_RX_USE_DMA 1 /**< RF RX over DMA */ #endif /** @} */ /*---------------------------------------------------------------------------*/ /** * \name IPv6, RIME and network buffer configuration * * @{ */ /* Don't let contiki-default-conf.h decide if we are an IPv6 build */ #ifndef NETSTACK_CONF_WITH_IPV6 #define NETSTACK_CONF_WITH_IPV6 0 #endif #if NETSTACK_CONF_WITH_IPV6 /* Addresses, Sizes and Interfaces */ /* 8-byte addresses here, 2 otherwise */ #define LINKADDR_CONF_SIZE 8 #define UIP_CONF_LL_802154 1 #define UIP_CONF_LLH_LEN 0 #define UIP_CONF_NETIF_MAX_ADDRESSES 3 /* TCP, UDP, ICMP */ #ifndef UIP_CONF_TCP #define UIP_CONF_TCP 1 #endif #ifndef UIP_CONF_TCP_MSS #define UIP_CONF_TCP_MSS 64 #endif #define UIP_CONF_UDP 1 #define UIP_CONF_UDP_CHECKSUMS 1 #define UIP_CONF_ICMP6 1 /* ND and Routing */ #ifndef UIP_CONF_ROUTER #define UIP_CONF_ROUTER 1 #endif #define UIP_CONF_ND6_SEND_RA 0 #define UIP_CONF_IP_FORWARD 0 #define RPL_CONF_STATS 0 #ifndef RPL_CONF_OF #define RPL_CONF_OF rpl_mrhof #endif #define UIP_CONF_ND6_REACHABLE_TIME 600000 #define UIP_CONF_ND6_RETRANS_TIMER 10000 #ifndef NBR_TABLE_CONF_MAX_NEIGHBORS #define NBR_TABLE_CONF_MAX_NEIGHBORS 20 #endif #ifndef UIP_CONF_MAX_ROUTES #define UIP_CONF_MAX_ROUTES 20 #endif /* uIP */ #ifndef UIP_CONF_BUFFER_SIZE #define UIP_CONF_BUFFER_SIZE 1300 #endif #define UIP_CONF_IPV6_QUEUE_PKT 0 #define UIP_CONF_IPV6_CHECKS 1 #define UIP_CONF_IPV6_REASSEMBLY 0 #define UIP_CONF_MAX_LISTENPORTS 8 /* 6lowpan */ #define SICSLOWPAN_CONF_COMPRESSION SICSLOWPAN_COMPRESSION_HC06 #ifndef SICSLOWPAN_CONF_COMPRESSION_THRESHOLD #define SICSLOWPAN_CONF_COMPRESSION_THRESHOLD 63 #endif #ifndef SICSLOWPAN_CONF_FRAG #define SICSLOWPAN_CONF_FRAG 1 #endif #define SICSLOWPAN_CONF_MAXAGE 8 /* Define our IPv6 prefixes/contexts here */ #define SICSLOWPAN_CONF_MAX_ADDR_CONTEXTS 1 #ifndef SICSLOWPAN_CONF_ADDR_CONTEXT_0 #define SICSLOWPAN_CONF_ADDR_CONTEXT_0 { \ addr_contexts[0].prefix[0] = 0xaa; \ addr_contexts[0].prefix[1] = 0xaa; \ } #endif #define MAC_CONF_CHANNEL_CHECK_RATE 8 #ifndef QUEUEBUF_CONF_NUM #define QUEUEBUF_CONF_NUM 8 #endif /*---------------------------------------------------------------------------*/ #else /* NETSTACK_CONF_WITH_IPV6 */ /* Network setup for non-IPv6 (rime). */ #define UIP_CONF_IP_FORWARD 1 #ifndef UIP_CONF_BUFFER_SIZE #define UIP_CONF_BUFFER_SIZE 108 #endif #define RIME_CONF_NO_POLITE_ANNOUCEMENTS 0 #ifndef QUEUEBUF_CONF_NUM #define QUEUEBUF_CONF_NUM 8 #endif #endif /* NETSTACK_CONF_WITH_IPV6 */ /** @} */ /*---------------------------------------------------------------------------*/ #endif /* CONTIKI_CONF_H_ */ /** @} */