80 lines
3.7 KiB
C
80 lines
3.7 KiB
C
/*
|
|
* Copyright (c) 2014, Texas Instruments Incorporated - http://www.ti.com/
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
#ifndef PROJECT_CONF_H_
|
|
#define PROJECT_CONF_H_
|
|
/*---------------------------------------------------------------------------*/
|
|
/* Change to match your configuration */
|
|
#define IEEE802154_CONF_PANID 0xABCD
|
|
#define IEEE802154_CONF_DEFAULT_CHANNEL 26
|
|
#define RF_BLE_CONF_ENABLED 1
|
|
/*---------------------------------------------------------------------------*/
|
|
|
|
/* Enable TCP */
|
|
#define UIP_CONF_TCP 1
|
|
|
|
/* Enable/Disable Components of this Demo */
|
|
#define CC26XX_WEB_DEMO_CONF_MQTT_CLIENT 1
|
|
#define CC26XX_WEB_DEMO_CONF_6LBR_CLIENT ROUTING_CONF_RPL_CLASSIC
|
|
#define CC26XX_WEB_DEMO_CONF_COAP_SERVER 1
|
|
#define CC26XX_WEB_DEMO_CONF_NET_UART 1
|
|
|
|
/*
|
|
* ADC sensor functionality. To test this, an external voltage source should be
|
|
* connected to DIO23
|
|
* Enable/Disable DIO23 ADC reading by setting CC26XX_WEB_DEMO_CONF_ADC_DEMO
|
|
*/
|
|
#define CC26XX_WEB_DEMO_CONF_ADC_DEMO 0
|
|
/*---------------------------------------------------------------------------*/
|
|
/*
|
|
* Change to 1 if you are using an older CC2650 Sensortag (look for Rev: 1.2
|
|
* printed on the PCB, or for a sticker reading "HW Rev 1.2.0").
|
|
*
|
|
* This may be the case if you are getting this error:
|
|
* "Could not open flash to load config"
|
|
* when your sensortag is starting up.
|
|
*/
|
|
#define SENSORTAG_CC2650_REV_1_2_0 0
|
|
/*---------------------------------------------------------------------------*/
|
|
/* Enable the ROM bootloader */
|
|
#define CCXXWARE_CONF_ROM_BOOTLOADER_ENABLE 1
|
|
/*---------------------------------------------------------------------------*/
|
|
/*
|
|
* Shrink the size of the uIP buffer, routing table and ND cache.
|
|
* Set the TCP MSS
|
|
*/
|
|
#define UIP_CONF_BUFFER_SIZE 500
|
|
#define NETSTACK_MAX_ROUTE_ENTRIES 5
|
|
#define NBR_TABLE_CONF_MAX_NEIGHBORS 5
|
|
#define UIP_CONF_TCP_MSS 128
|
|
/*---------------------------------------------------------------------------*/
|
|
#endif /* PROJECT_CONF_H_ */
|
|
/*---------------------------------------------------------------------------*/
|