nes-proj/arch/cpu/cc2538/cc2538-conf.h

323 lines
9.5 KiB
C
Raw Normal View History

/*
* Copyright (c) 2017, George Oikonomou - http://www.spd.gr
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the copyright holder nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
* OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/*---------------------------------------------------------------------------*/
/**
* \addtogroup cc2538
* @{
*/
/*---------------------------------------------------------------------------*/
#ifndef CC2538_CONF_H_
#define CC2538_CONF_H_
/*---------------------------------------------------------------------------*/
/**
* \name CFS configuration
*
* @{
*/
#ifndef COFFEE_CONF_SIZE
#define COFFEE_CONF_SIZE (4 * COFFEE_SECTOR_SIZE)
#endif
/** @} */
/*---------------------------------------------------------------------------*/
/**
* \name CC2538 System Control configuration
*
* @{
*/
#ifndef SYS_CTRL_CONF_OSC32K_USE_XTAL
#define SYS_CTRL_CONF_OSC32K_USE_XTAL 0 /**< Use the on-board 32.768-kHz crystal */
#endif
/** @} */
/*---------------------------------------------------------------------------*/
/**
* \name Watchdog Timer configuration
*
* @{
*/
#ifndef WATCHDOG_CONF_ENABLE
#define WATCHDOG_CONF_ENABLE 1 /**< Enable the watchdog timer */
#endif
/** @} */
/*---------------------------------------------------------------------------*/
/**
* \name USB 'core' configuration
*
* Those values are not meant to be modified by the user, except where stated
* otherwise
* @{
*/
#define CTRL_EP_SIZE 8
#define USB_EP1_SIZE 32
#define USB_EP2_SIZE 64
#define USB_EP3_SIZE 64
#define USB_ARCH_WRITE_NOTIFY 0
#ifndef USB_ARCH_CONF_DMA
#define USB_ARCH_CONF_DMA 1 /**< Change to Enable/Disable USB DMA */
#endif
/** @} */
/**
* \name uDMA Configuration and channel allocations
*
* @{
*/
#define USB_ARCH_CONF_RX_DMA_CHAN 0 /**< USB -> RAM DMA channel */
#define USB_ARCH_CONF_TX_DMA_CHAN 1 /**< RAM -> USB DMA channel */
#define CC2538_RF_CONF_TX_DMA_CHAN 2 /**< RF -> RAM DMA channel */
#define CC2538_RF_CONF_RX_DMA_CHAN 3 /**< RAM -> RF DMA channel */
#define UDMA_CONF_MAX_CHANNEL CC2538_RF_CONF_RX_DMA_CHAN
/** @} */
/*---------------------------------------------------------------------------*/
/**
* \name Character I/O Configuration
*
* @{
*/
#ifndef UART_CONF_ENABLE
#define UART_CONF_ENABLE 1 /**< Enable/Disable UART I/O */
#endif
#ifndef UART0_CONF_BAUD_RATE
#define UART0_CONF_BAUD_RATE 115200 /**< Default UART0 baud rate */
#endif
#ifndef UART1_CONF_BAUD_RATE
#define UART1_CONF_BAUD_RATE 115200 /**< Default UART1 baud rate */
#endif
#ifndef SLIP_ARCH_CONF_USB
#define SLIP_ARCH_CONF_USB 0 /**< SLIP over UART by default */
#endif
#ifndef DBG_CONF_USB
#define DBG_CONF_USB 0 /**< All debugging over UART by default */
#endif
#ifndef SERIAL_LINE_CONF_UART
#define SERIAL_LINE_CONF_UART 0 /**< UART to use with serial line */
#endif
#if !SLIP_ARCH_CONF_USB
#ifndef SLIP_ARCH_CONF_UART
#define SLIP_ARCH_CONF_UART 0 /**< UART to use with SLIP */
#endif
#endif
#if !DBG_CONF_USB
#ifndef DBG_CONF_UART
#define DBG_CONF_UART 0 /**< UART to use for debugging */
#endif
#endif
#ifndef UART1_CONF_UART
#define UART1_CONF_UART 0 /**< UART to use for examples relying on
the uart1_* API */
#endif
#ifndef SLIP_ARCH_CONF_ENABLED
/*
* Determine whether we need SLIP
* This will keep working while UIP_FALLBACK_INTERFACE and CMD_CONF_OUTPUT
* keep using SLIP
*/
#if defined(UIP_FALLBACK_INTERFACE) || defined(CMD_CONF_OUTPUT)
#define SLIP_ARCH_CONF_ENABLED 1
#endif
#endif
/**
* \brief Define this as 1 to build a headless node.
*
* The UART will not be initialised its clock will be gated, offering some
* energy savings. The USB will not be initialised either
*/
#ifndef CC2538_CONF_QUIET
#define CC2538_CONF_QUIET 0
#endif
/* CC2538_CONF_QUIET is hard and overrides all other related defines */
#if CC2538_CONF_QUIET
#undef USB_SERIAL_CONF_ENABLE
#define USB_SERIAL_CONF_ENABLE 0
#undef UART_CONF_ENABLE
#define UART_CONF_ENABLE 0
#endif /* CC2538_CONF_QUIET */
/**
* \brief Enable the USB core only if we need it
*/
#ifndef USB_SERIAL_CONF_ENABLE
#define USB_SERIAL_CONF_ENABLE \
((SLIP_ARCH_CONF_USB && SLIP_ARCH_CONF_ENABLED) || \
(MAC_CONF_WITH_TSCH && (SLIP_ARCH_CONF_ENABLED || BUILD_WITH_SHELL)) || \
DBG_CONF_USB)
#endif
/*
* If debugging and SLIP use the same peripheral, this will be 1. Don't modify
* this
*/
#if SLIP_ARCH_CONF_ENABLED
#define DBG_CONF_SLIP_MUX (SLIP_ARCH_CONF_USB == DBG_CONF_USB && \
(SLIP_ARCH_CONF_USB || \
SLIP_ARCH_CONF_UART == DBG_CONF_UART))
#endif
/*
* Automatic detection of whether a specific UART is in use
*/
#define UART_IN_USE_BY_SERIAL_LINE(u) (SERIAL_LINE_CONF_UART == (u))
#define UART_IN_USE_BY_SLIP(u) (SLIP_ARCH_CONF_ENABLED && \
!SLIP_ARCH_CONF_USB && \
SLIP_ARCH_CONF_UART == (u))
#define UART_IN_USE_BY_DBG(u) (!DBG_CONF_USB && DBG_CONF_UART == (u))
#define UART_IN_USE_BY_UART1(u) (UART1_CONF_UART == (u))
#define UART_IN_USE(u) ( \
UART_CONF_ENABLE && \
(UART_IN_USE_BY_SERIAL_LINE(u) || \
UART_IN_USE_BY_SLIP(u) || \
UART_IN_USE_BY_DBG(u) || \
UART_IN_USE_BY_UART1(u)) \
)
/** @} */
/*---------------------------------------------------------------------------*/
/**
* \name RF configuration
*
* @{
*/
/* RF Config */
#ifndef CC2538_RF_CONF_AUTOACK
#define CC2538_RF_CONF_AUTOACK 1 /**< RF H/W generates ACKs */
#endif /* CC2538_CONF_AUTOACK */
#ifndef CC2538_RF_CONF_TX_USE_DMA
#define CC2538_RF_CONF_TX_USE_DMA 1 /**< RF TX over DMA */
#endif
#ifndef CC2538_RF_CONF_RX_USE_DMA
#define CC2538_RF_CONF_RX_USE_DMA 1 /**< RF RX over DMA */
#endif
/** @} */
/*---------------------------------------------------------------------------*/
/**
* \name LPM configuration
* @{
*/
#ifndef LPM_CONF_ENABLE
#define LPM_CONF_ENABLE 1 /**< Set to 0 to disable LPM entirely */
#endif
/**
* \brief Maximum PM
*
* The SoC will never drop to a Power Mode deeper than the one specified here.
* 0 for PM0, 1 for PM1 and 2 for PM2
*/
#ifndef LPM_CONF_MAX_PM
#define LPM_CONF_MAX_PM 1
#endif
#ifndef LPM_CONF_STATS
#define LPM_CONF_STATS 0 /**< Set to 1 to enable LPM-related stats */
#endif
/** @} */
/*---------------------------------------------------------------------------*/
/**
* \name Radio Configuration
*
* @{
*/
#ifndef NETSTACK_CONF_RADIO
#define NETSTACK_CONF_RADIO cc2538_rf_driver
#endif
/** @} */
/*---------------------------------------------------------------------------*/
/**
* \name IEEE address configuration
*
* Used to generate our link-layer & IPv6 address
* @{
*/
/**
* \brief Location of the IEEE address
* 0 => Read from InfoPage,
* 1 => Use a hardcoded address, configured by IEEE_ADDR_CONF_ADDRESS
*/
#ifndef IEEE_ADDR_CONF_HARDCODED
#define IEEE_ADDR_CONF_HARDCODED 0
#endif
/**
* \brief The hardcoded IEEE address to be used when IEEE_ADDR_CONF_HARDCODED
* is defined as 1
*/
#ifndef IEEE_ADDR_CONF_ADDRESS
#define IEEE_ADDR_CONF_ADDRESS { 0x00, 0x12, 0x4B, 0x00, 0x89, 0xAB, 0xCD, 0xEF }
#endif
/**
* \brief Location of the IEEE address in the InfoPage when
* IEEE_ADDR_CONF_HARDCODED is defined as 0
* 0 => Use the primary address location
* 1 => Use the secondary address location
*/
#ifndef IEEE_ADDR_CONF_USE_SECONDARY_LOCATION
#define IEEE_ADDR_CONF_USE_SECONDARY_LOCATION 0
#endif
/** @} */
/*---------------------------------------------------------------------------*/
/**
* \name Security
*
* @{
*/
#ifndef CRYPTO_CONF_INIT
#define CRYPTO_CONF_INIT 1 /**< Whether to init cryptoprocessor */
#endif
#ifndef AES_128_CONF
#define AES_128_CONF cc2538_aes_128_driver /**< AES-128 driver */
#endif
#ifndef CCM_STAR_CONF
#define CCM_STAR_CONF cc2538_ccm_star_driver /**< AES-CCM* driver */
#endif
/** @} */
/*---------------------------------------------------------------------------*/
#endif /* CC2538_CONF_H_ */
/*---------------------------------------------------------------------------*/
/** @} */