nes-proj/cpu/cc26xx/dev/rfc-api/ieee_mailbox.h

108 lines
5.0 KiB
C
Raw Normal View History

2015-02-25 12:09:56 +00:00
/******************************************************************************
* Filename: ieee_mailbox.h
* Revised: $ $
* Revision: $ $
*
* Description: Definitions for IEEE 802.15.4 interface
*
* Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
*
* Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* Neither the name of Texas Instruments Incorporated nor the names of
* its contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************/
#ifndef _IEEE_MAILBOX_H
#define _IEEE_MAILBOX_H
#include "mailbox.h"
/// \name CPE interrupt definitions for IEEE 802.15.4
/// Interrupt masks for the CPE interrupt in RDBELL. These are new names for interrupts in mailbox.h,
/// used for compartibility with previous versions with separate interrupt numbers.
///@{
#define IRQN_IEEE_BG_COMMAND_SUSPENDED IRQN_BG_COMMAND_SUSPENDED
#define IRQN_IEEE_TX_FRAME IRQN_TX_DONE
#define IRQN_IEEE_TX_ACK IRQN_TX_ACK
#define IRQN_IEEE_RX_FRAME IRQN_RX_OK
#define IRQN_IEEE_RX_NOK IRQN_RX_NOK
#define IRQN_IEEE_RX_IGNORED IRQN_RX_IGNORED
#define IRQN_IEEE_RX_BUF_FULL IRQN_RX_BUF_FULL
#define IRQN_IEEE_RX_ENTRY_DONE IRQN_RX_ENTRY_DONE
#define IRQ_IEEE_BG_COMMAND_SUSPENDED (1U << IRQN_IEEE_BG_COMMAND_SUSPENDED)
#define IRQ_IEEE_TX_FRAME (1U << IRQN_IEEE_TX_FRAME)
#define IRQ_IEEE_TX_ACK (1U << IRQN_IEEE_TX_ACK)
#define IRQ_IEEE_RX_FRAME (1U << IRQN_IEEE_RX_FRAME)
#define IRQ_IEEE_RX_NOK (1U << IRQN_IEEE_RX_NOK)
#define IRQ_IEEE_RX_IGNORED (1U << IRQN_IEEE_RX_IGNORED)
#define IRQ_IEEE_RX_BUF_FULL (1U << IRQN_IEEE_RX_BUF_FULL)
#define IRQ_IEEE_RX_ENTRY_DONE (1U << IRQN_IEEE_RX_ENTRY_DONE)
///@}
/// \name Radio operation status
/// Radio operation status format:
/// Bits 15:12: Protocol
/// 0010: IEEE 802.15.4
/// Bits 11:10: Type
/// 00: Not finished
/// 01: Done successfully
/// 10: Done with error
/// Bits 9:0: Identifier
/// \name Operation not finished
///@{
#define IEEE_SUSPENDED 0x2001 ///< Operation suspended
///@}
/// \name Operation finished normally
///@{
#define IEEE_DONE_OK 0x2400 ///< Operation ended normally
#define IEEE_DONE_BUSY 0x2401 ///< CSMA-CA operation ended with failure
#define IEEE_DONE_STOPPED 0x2402 ///< Operation stopped after stop command
#define IEEE_DONE_ACK 0x2403 ///< ACK packet received with pending data bit cleared
#define IEEE_DONE_ACKPEND 0x2404 ///< ACK packet received with pending data bit set
#define IEEE_DONE_TIMEOUT 0x2405 ///< Operation ended due to timeout
#define IEEE_DONE_BGEND 0x2406 ///< FG operation ended because necessary background level
///< operation ended
#define IEEE_DONE_ABORT 0x2407 ///< Operation aborted by command
///@}
/// \name Operation finished with error
///@{
#define IEEE_ERROR_PAR 0x2800 ///< Illegal parameter
#define IEEE_ERROR_NO_SETUP 0x2801 ///< Operation using Rx or Tx attemted when not in 15.4 mode
#define IEEE_ERROR_NO_FS 0x2802 ///< Operation using Rx or Tx attemted without frequency synth configured
#define IEEE_ERROR_SYNTH_PROG 0x2803 ///< Synthesizer programming failed to complete on time
#define IEEE_ERROR_RXOVF 0x2804 ///< Receiver overflowed during operation
#define IEEE_ERROR_TXUNF 0x2805 ///< Transmitter underflowed during operation
///@}
///@}
#endif