nes-proj/drivers/platform/zoul/dev/pm10-sensor.c

/*
 * Copyright (c) 2016, Zolertia <http://www.zolertia.com>
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. Neither the name of the Institute nor the names of its contributors
 *    may be used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 *
 * This file is part of the Contiki operating system.
 *
 */
/*---------------------------------------------------------------------------*/
/**
 * \addtogroup zoul-pm10-sensor
 * @{
 *
 * \file
 *      GP2Y1010AU0F PM10 sensor example using the ADC sensors wrapper  
 * \author
 *      Toni Lozano <tlozano@zolertia.com>
 */
/*---------------------------------------------------------------------------*/
#include <stdio.h>
#include "contiki.h"
#include "adc-sensors.h"
#include "adc-zoul.h"
#include "zoul-sensors.h"
#include "dev/pm10-sensor.h"
#include "dev/sys-ctrl.h"
#include "lib/sensors.h"
#include "dev/gpio.h"
#include "dev/ioc.h"
/*---------------------------------------------------------------------------*/
#define PM10_SENSOR_PORT_BASE   GPIO_PORT_TO_BASE(PM10_SENSOR_CTRL_PORT)
#define PM10_SENSOR_PIN_MASK    GPIO_PIN_MASK(PM10_SENSOR_CTRL_PIN)
/*---------------------------------------------------------------------------*/
static int pm10_channel;
/*---------------------------------------------------------------------------*/
static int
configure(int type, int value)
{
  if(type != SENSORS_ACTIVE) {
    return PM10_ERROR;
  }

  if(value) {
    /* Set as output, used as pulse-driven wave */
    GPIO_SOFTWARE_CONTROL(PM10_SENSOR_PORT_BASE, PM10_SENSOR_PIN_MASK);
    ioc_set_over(PM10_SENSOR_CTRL_PORT, PM10_SENSOR_CTRL_PIN, IOC_OVERRIDE_DIS); 
    GPIO_SET_OUTPUT(PM10_SENSOR_PORT_BASE, PM10_SENSOR_PIN_MASK);
    GPIO_CLR_PIN(PM10_SENSOR_PORT_BASE, PM10_SENSOR_PIN_MASK);

    pm10_channel = (1 << value);
    return adc_zoul.configure(SENSORS_HW_INIT, pm10_channel);
  }

  pm10_channel = 0;
  return PM10_SUCCESS;
}
/*---------------------------------------------------------------------------*/
static int
value(int type)
{
  uint32_t val;

  if(!pm10_channel) {
    return PM10_ERROR;
  }

  /* Set Pulse Wave pin before measure */
  GPIO_SET_PIN(PM10_SENSOR_PORT_BASE, PM10_SENSOR_PIN_MASK);
  /* Pulse wave delay */
  clock_delay_usec(PM10_SENSOR_PULSE_DELAY);
  /* Data acquisition */  
  val = (uint32_t)adc_zoul.value(pm10_channel); 

  if(val == ZOUL_SENSORS_ERROR) {
    printf("PM10 sensor: failed retrieving data\n");
    return PM10_ERROR;
  }

  /* Default voltage divisor relation is 5/3 aprox, change at adc_wrapper.h,
   * calculations below assume a decimation rate of 512 (12 bits ENOB) and
   * AVVD5 voltage reference of 3.3V
   */
  val *= PM10_EXTERNAL_VREF;
  val /= PM10_EXTERNAL_VREF_CROSSVAL;

  /* Applied constant conversion from UAir project
   * to obtain value in ppm (value in mV * 0.28)
   */
  val *= 28;
  val /= 1000;

  /* Clear pulse wave pin */
  GPIO_CLR_PIN(PM10_SENSOR_PORT_BASE, PM10_SENSOR_PIN_MASK);
  
  return (uint16_t)val;
}
/*---------------------------------------------------------------------------*/
SENSORS_SENSOR(pm10, PM10_SENSOR, value, configure, NULL);
/*---------------------------------------------------------------------------*/
/** @} */