nes-proj/arch/cpu/cc13xx-cc26xx/rf-settings/cc26x2/ieee-settings.c

/*
 * Copyright (c) 2018, Texas Instruments Incorporated - http://www.ti.com/
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. Neither the name of the copyright holder nor the names of its
 *    contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE
 * COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
 * OF THE POSSIBILITY OF SUCH DAMAGE.
 */
/*---------------------------------------------------------------------------*/
// Parameter summary
// IEEE Channel: 11
// Frequency: 2405 MHz
// SFD: 0
// Packet Data: 255
// Preamble (32 bit): 01010101...
// TX Power: 5 dBm
/*---------------------------------------------------------------------------*/
#include "sys/cc.h"
/*---------------------------------------------------------------------------*/
#include <ti/devices/DeviceFamily.h>
#include DeviceFamily_constructPath(driverlib/rf_mailbox.h)
#include DeviceFamily_constructPath(driverlib/rf_common_cmd.h)
#include DeviceFamily_constructPath(driverlib/rf_ieee_cmd.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_ieee_802_15_4.h)
#include DeviceFamily_constructPath(rf_patches/rf_patch_mce_ieee_802_15_4.h)

#include <ti/drivers/rf/RF.h>
/*---------------------------------------------------------------------------*/
#include "ieee-settings.h"
/*---------------------------------------------------------------------------*/
// TI-RTOS RF Mode Object
RF_Mode rf_ieee_mode =
{
    .rfMode = RF_MODE_AUTO,
    .cpePatchFxn = &rf_patch_cpe_ieee_802_15_4,
    .mcePatchFxn = &rf_patch_mce_ieee_802_15_4,
    .rfePatchFxn = 0,
};
/*---------------------------------------------------------------------------*/
// TX Power table
// The RF_TxPowerTable_DEFAULT_PA_ENTRY macro is defined in RF.h and requires the following arguments:
// RF_TxPowerTable_DEFAULT_PA_ENTRY(bias, gain, boost coefficient)
// See the Technical Reference Manual for further details about the "txPower" Command field.
// The PA settings require the CCFG_FORCE_VDDR_HH = 0 unless stated otherwise.
RF_TxPowerTable_Entry rf_ieee_tx_power_table[RF_IEEE_TX_POWER_TABLE_SIZE+1] =
{
    { -21, RF_TxPowerTable_DEFAULT_PA_ENTRY(7,  3, 0,   3) },
    { -18, RF_TxPowerTable_DEFAULT_PA_ENTRY(9,  3, 0,   3) },
    { -15, RF_TxPowerTable_DEFAULT_PA_ENTRY(12, 2, 0, 100) },
    { -12, RF_TxPowerTable_DEFAULT_PA_ENTRY(40, 2, 0,   8) },
    { -10, RF_TxPowerTable_DEFAULT_PA_ENTRY(12, 2, 0,  11) },
    {  -9, RF_TxPowerTable_DEFAULT_PA_ENTRY(13, 2, 0,   5) },
    {  -6, RF_TxPowerTable_DEFAULT_PA_ENTRY(13, 1, 0,  16) },
    {  -5, RF_TxPowerTable_DEFAULT_PA_ENTRY(14, 1, 0,  17) },
    {  -3, RF_TxPowerTable_DEFAULT_PA_ENTRY(17, 1, 0,  20) },
    {   0, RF_TxPowerTable_DEFAULT_PA_ENTRY(25, 1, 0,  26) },
    {   1, RF_TxPowerTable_DEFAULT_PA_ENTRY(28, 1, 0,  28) },
    {   2, RF_TxPowerTable_DEFAULT_PA_ENTRY(13, 0, 0,  34) },
    {   3, RF_TxPowerTable_DEFAULT_PA_ENTRY(17, 0, 0,  42) },
    {   4, RF_TxPowerTable_DEFAULT_PA_ENTRY(22, 0, 0,  54) },
    {   5, RF_TxPowerTable_DEFAULT_PA_ENTRY(30, 0, 0,  74) },
    RF_TxPowerTable_TERMINATION_ENTRY
};
/*---------------------------------------------------------------------------*/
// Overrides for CMD_RADIO_SETUP
uint32_t rf_ieee_overrides[] CC_ALIGN(4) =
{
                                    // override_ieee_802_15_4.xml
    MCE_RFE_OVERRIDE(1,0,0,0,1,0),  // PHY: Use MCE RAM patch, RFE ROM bank 1
    (uint32_t)0x02400403,           // Synth: Use 48 MHz crystal, enable extra PLL filtering
    (uint32_t)0x001C8473,           // Synth: Configure extra PLL filtering
    (uint32_t)0x00088433,           // Synth: Configure synth hardware
    (uint32_t)0x00038793,           // Synth: Set minimum RTRIM to 3
    HW32_ARRAY_OVERRIDE(0x4004,1),  // Synth: Configure faster calibration
    (uint32_t)0x1C0C0618,           // Synth: Configure faster calibration
    (uint32_t)0xC00401A1,           // Synth: Configure faster calibration
    (uint32_t)0x00010101,           // Synth: Configure faster calibration
    (uint32_t)0xC0040141,           // Synth: Configure faster calibration
    (uint32_t)0x00214AD3,           // Synth: Configure faster calibration
    (uint32_t)0x02980243,           // Synth: Decrease synth programming time-out (0x0298 RAT ticks = 166 us)
    (uint32_t)0xFCFC08C3,           // DC/DC regulator: In Tx, use DCDCCTL5[3:0]=0xC (DITHER_EN=1 and IPEAK=4). In Rx, use DCDCCTL5[3:0]=0xC (DITHER_EN=1 and IPEAK=4).
    (uint32_t)0x000F8883,           // Rx: Set LNA bias current offset to +15 to saturate trim to max (default: 0)
    (uint32_t)0xFFFFFFFF,
};
/*---------------------------------------------------------------------------*/
// CMD_RADIO_SETUP
// Radio Setup Command for Pre-Defined Schemes
rfc_CMD_RADIO_SETUP_t rf_cmd_ieee_radio_setup =
{
    .commandNo = CMD_RADIO_SETUP,
    .status = IDLE,
    .pNextOp = 0,
    .startTime = 0x00000000,
    .startTrigger.triggerType = TRIG_NOW,
    .startTrigger.bEnaCmd = 0x0,
    .startTrigger.triggerNo = 0x0,
    .startTrigger.pastTrig = 0x0,
    .condition.rule = COND_NEVER,
    .condition.nSkip = 0x0,
    .mode = 0x01,
    .loDivider = 0x00,
    .config.frontEndMode = 0x0,
    .config.biasMode = 0x1,
    .config.analogCfgMode = 0x0,
    .config.bNoFsPowerUp = 0x0,
    .txPower = 0x941E, /* 5 dBm default */
    .pRegOverride = rf_ieee_overrides,
};
/*---------------------------------------------------------------------------*/
// CMD_FS
// Frequency Synthesizer Programming Command
rfc_CMD_FS_t rf_cmd_ieee_fs =
{
    .commandNo = CMD_FS,
    .status = IDLE,
    .pNextOp = 0,
    .startTime = 0x00000000,
    .startTrigger.triggerType = TRIG_NOW,
    .startTrigger.bEnaCmd = 0x0,
    .startTrigger.triggerNo = 0x0,
    .startTrigger.pastTrig = 0x0,
    .condition.rule = COND_NEVER,
    .condition.nSkip = 0x0,
    .frequency = 0x0965, /* set by driver */
    .fractFreq = 0x0000, /* set by driver */
    .synthConf.bTxMode = 0x1,
    .synthConf.refFreq = 0x0,
    .__dummy0 = 0x00,
    .__dummy1 = 0x00,
    .__dummy2 = 0x00,
    .__dummy3 = 0x0000,
};
/*---------------------------------------------------------------------------*/
// CMD_IEEE_TX
// IEEE 802.15.4 Transmit Command
rfc_CMD_IEEE_TX_t rf_cmd_ieee_tx =
{
    .commandNo = CMD_IEEE_TX,
    .status = IDLE,
    .pNextOp = 0,
    .startTime = 0x00000000,
    .startTrigger.triggerType = TRIG_NOW,
    .startTrigger.bEnaCmd = 0x0,
    .startTrigger.triggerNo = 0x0,
    .startTrigger.pastTrig = 0x0,
    .condition.rule = COND_NEVER,
    .condition.nSkip = 0x0,
    .txOpt.bIncludePhyHdr = 0x0,
    .txOpt.bIncludeCrc = 0x0,
    .txOpt.payloadLenMsb = 0x0,
    .payloadLen = 0x0, /* set by driver */
    .pPayload = 0, /* set by driver */
    .timeStamp = 0x00000000,
};
/*---------------------------------------------------------------------------*/
// CMD_IEEE_RX
// IEEE 802.15.4 Receive Command
rfc_CMD_IEEE_RX_t rf_cmd_ieee_rx =
{
    .commandNo = CMD_IEEE_RX,
    .status = IDLE,
    .pNextOp = 0,
    .startTime = 0x00000000,
    .startTrigger.triggerType = TRIG_NOW,
    .startTrigger.bEnaCmd = 0x0,
    .startTrigger.triggerNo = 0x0,
    .startTrigger.pastTrig = 0x0,
    .condition.rule = COND_NEVER,
    .condition.nSkip = 0x0,
    .channel = 0x00, /* set by driver */
    .rxConfig.bAutoFlushCrc = 0x1,
    .rxConfig.bAutoFlushIgn = 0x0,
    .rxConfig.bIncludePhyHdr = 0x0,
    .rxConfig.bIncludeCrc = 0x1,
    .rxConfig.bAppendRssi = 0x1,
    .rxConfig.bAppendCorrCrc = 0x1,
    .rxConfig.bAppendSrcInd = 0x0,
    .rxConfig.bAppendTimestamp = 0x1,
    .pRxQ = 0, /* set by driver */
    .pOutput = 0, /* set by driver */
    .frameFiltOpt.frameFiltEn = 0x0, /* set by driver */
    .frameFiltOpt.frameFiltStop = 0x1,
    .frameFiltOpt.autoAckEn = 0x0, /* set by driver */
    .frameFiltOpt.slottedAckEn = 0x0,
    .frameFiltOpt.autoPendEn = 0x0,
    .frameFiltOpt.defaultPend = 0x0,
    .frameFiltOpt.bPendDataReqOnly = 0x0,
    .frameFiltOpt.bPanCoord = 0x0,
    .frameFiltOpt.maxFrameVersion = 0x2,
    .frameFiltOpt.fcfReservedMask = 0x0,
    .frameFiltOpt.modifyFtFilter = 0x0,
    .frameFiltOpt.bStrictLenFilter = 0x0,
    .frameTypes.bAcceptFt0Beacon = 0x1,
    .frameTypes.bAcceptFt1Data = 0x1,
    .frameTypes.bAcceptFt2Ack = 0x1,
    .frameTypes.bAcceptFt3MacCmd = 0x1,
    .frameTypes.bAcceptFt4Reserved = 0x1,
    .frameTypes.bAcceptFt5Reserved = 0x1,
    .frameTypes.bAcceptFt6Reserved = 0x1,
    .frameTypes.bAcceptFt7Reserved = 0x1,
    .ccaOpt.ccaEnEnergy = 0x1,
    .ccaOpt.ccaEnCorr = 0x1,
    .ccaOpt.ccaEnSync = 0x1,
    .ccaOpt.ccaCorrOp = 0x1,
    .ccaOpt.ccaSyncOp = 0x0,
    .ccaOpt.ccaCorrThr = 0x3,
    .ccaRssiThr = 0x0, /* set by driver */
    .__dummy0 = 0x00,
    .numExtEntries = 0x00,
    .numShortEntries = 0x00,
    .pExtEntryList = 0,
    .pShortEntryList = 0,
    .localExtAddr = 0x0, /* set by driver */
    .localShortAddr = 0x0, /* set by driver */
    .localPanID = 0x0000,
    .__dummy1 = 0x000000,
    .endTrigger.triggerType = TRIG_NEVER,
    .endTrigger.bEnaCmd = 0x0,
    .endTrigger.triggerNo = 0x0,
    .endTrigger.pastTrig = 0x0,
    .endTime = 0x00000000,
};
/*---------------------------------------------------------------------------*/