Create a dedicated header file with all the definitions for the flash lock bit
page and customer configuration area. This avoids duplicating those definitions
in the startup-gcc.c files of all CC2538-based platforms, and this also allows
to easily manipulate the CCA from outside startup-gcc.c (e.g. for on-the-air
firmware update).
The definitions are now complete contrary to what was in startup-gcc.c:
- Definitions have been added to select the bootloader backdoor pin and active
level if enabled.
- Definitions have been added to access the page and debug lock bits. The debug
lock bit can be used to prevent someone from reading back a programmed
firmware through JTAG if the firmware binary image has to be confidential,
which should be combined with a disabled bootloader backdoor.
- The application entry point is now tied to the beginning of the .text section
instead of to the beginning of the flash. This allows projects using custom
linker scripts to place the application entry point anywhere in the flash,
which can be useful e.g. for on-the-air firmware update.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
SYS_CTRL_EMUOVR is already defined in sys-ctrl.h, so #include this header file
instead of redefining SYS_CTRL_EMUOVR in startup-gcc.c.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
It cannot be ruled out that access to the address register triggers
an address auto-increment. Therefore a temporary address register
shadow is introduced to replace the access to the address regsiter.
Additionally there are several minor beautifications.
This patch adds the eeprom driver needed to access M24C64
eeprom which is on some mbxxx boards.
Signed-off-by: Maria Laura Stefanizzi <laura28582@gmail.com>
This patch add the I2C driver for mbxxx platform to communicate with
devices connected to the SC2 I2C bus.
Signed-off-by: Maria Laura Stefanizzi <laura28582@gmail.com>
The pending GPIO power-up interrupts have to be cleared in the ISRs in order not
to re-trigger the interrupts and the wake-up events.
The power-up interrupts of all pins are cleared for each port in the
corresponding port ISR. This is done after calling the registered callbacks so
that the callbacks can know which pin woke up the SoC. This is done after
clearing the regular interrupt in order to avoid getting a new wake-up interrupt
without the regular interrupt in the case of a new wake-up edge occurring
between the two clears.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The GPIO power-up interrupts have to be configured and enabled in order to be
able to wake-up the SoC from PM1+ upon a signal edge occurring on a GPIO input
pin.
This set of macros allows to:
- configure the signal edge triggering a power-up interrupt,
- enable and disable a power-up interrupt,
- clear a power-up interrupt flag.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
As the comment in contiki-conf.h says, the automatic definition of
SLIP_ARCH_CONF_ENABLED works only if UIP_FALLBACK_INTERFACE is tied to SLIP. If
UIP_FALLBACK_INTERFACE is set to another interface, SLIP_ARCH_CONF_ENABLED is
still automatically set to 1, leading to unwanted SLIP_END characters from
dbg.c:putchar() being printed on the UART.
This change makes it possible to force the definition of SLIP_ARCH_CONF_ENABLED
(e.g. from project-conf.h), so that it can be disabled if UIP_FALLBACK_INTERFACE
is used with something else than SLIP.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
