nes-proj/examples/platform-specific/cc26xx/cc26xx-web-demo/project-conf.h
George Oikonomou 06bbb65bdb Simplify configuration of the CC13xx/CC26xx ROM bootloader
Currently board.h does all the work, but it does not really need to. This commit moves most of the ccfg defines to ccxxware-conf.h and now board.h only needs to specify the bootloader enable pin and corresponding level.
2018-09-17 13:15:58 +03:00

80 lines
3.7 KiB
C

/*
* Copyright (c) 2014, Texas Instruments Incorporated - http://www.ti.com/
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the copyright holder nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
* OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/*---------------------------------------------------------------------------*/
#ifndef PROJECT_CONF_H_
#define PROJECT_CONF_H_
/*---------------------------------------------------------------------------*/
/* Change to match your configuration */
#define IEEE802154_CONF_PANID 0xABCD
#define IEEE802154_CONF_DEFAULT_CHANNEL 26
#define RF_BLE_CONF_ENABLED 1
/*---------------------------------------------------------------------------*/
/* Enable TCP */
#define UIP_CONF_TCP 1
/* Enable/Disable Components of this Demo */
#define CC26XX_WEB_DEMO_CONF_MQTT_CLIENT 1
#define CC26XX_WEB_DEMO_CONF_6LBR_CLIENT ROUTING_CONF_RPL_CLASSIC
#define CC26XX_WEB_DEMO_CONF_COAP_SERVER 1
#define CC26XX_WEB_DEMO_CONF_NET_UART 1
/*
* ADC sensor functionality. To test this, an external voltage source should be
* connected to DIO23
* Enable/Disable DIO23 ADC reading by setting CC26XX_WEB_DEMO_CONF_ADC_DEMO
*/
#define CC26XX_WEB_DEMO_CONF_ADC_DEMO 0
/*---------------------------------------------------------------------------*/
/*
* Change to 1 if you are using an older CC2650 Sensortag (look for Rev: 1.2
* printed on the PCB, or for a sticker reading "HW Rev 1.2.0").
*
* This may be the case if you are getting this error:
* "Could not open flash to load config"
* when your sensortag is starting up.
*/
#define SENSORTAG_CC2650_REV_1_2_0 0
/*---------------------------------------------------------------------------*/
/* Enable the ROM bootloader */
#define CCXXWARE_CONF_ROM_BOOTLOADER_ENABLE 1
/*---------------------------------------------------------------------------*/
/*
* Shrink the size of the uIP buffer, routing table and ND cache.
* Set the TCP MSS
*/
#define UIP_CONF_BUFFER_SIZE 500
#define NETSTACK_MAX_ROUTE_ENTRIES 5
#define NBR_TABLE_CONF_MAX_NEIGHBORS 5
#define UIP_CONF_TCP_MSS 128
/*---------------------------------------------------------------------------*/
#endif /* PROJECT_CONF_H_ */
/*---------------------------------------------------------------------------*/