227 lines
7.0 KiB
C
227 lines
7.0 KiB
C
/*
|
|
* Copyright (c) 2010, Swedish Institute of Computer Science
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the Institute nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
*/
|
|
|
|
/*
|
|
* Machine dependent MSP430X UART0 code.
|
|
*/
|
|
|
|
#include <stdlib.h>
|
|
|
|
#include "contiki.h"
|
|
#include "sys/energest.h"
|
|
#include "dev/uart0.h"
|
|
#include "dev/watchdog.h"
|
|
#include "lib/ringbuf.h"
|
|
#include "isr_compat.h"
|
|
|
|
static int (*uart0_input_handler)(unsigned char c);
|
|
|
|
static volatile uint8_t transmitting;
|
|
|
|
#ifdef UART0_CONF_TX_WITH_INTERRUPT
|
|
#define TX_WITH_INTERRUPT UART0_CONF_TX_WITH_INTERRUPT
|
|
#else /* UART0_CONF_TX_WITH_INTERRUPT */
|
|
#define TX_WITH_INTERRUPT 1
|
|
#endif /* UART0_CONF_TX_WITH_INTERRUPT */
|
|
|
|
#ifdef UART0_CONF_RX_WITH_DMA
|
|
#define RX_WITH_DMA UART0_CONF_RX_WITH_DMA
|
|
#else /* UART0_CONF_RX_WITH_DMA */
|
|
#define RX_WITH_DMA 1
|
|
#endif /* UART0_CONF_RX_WITH_DMA */
|
|
|
|
#if TX_WITH_INTERRUPT
|
|
#define TXBUFSIZE 64
|
|
|
|
static struct ringbuf txbuf;
|
|
static uint8_t txbuf_data[TXBUFSIZE];
|
|
#endif /* TX_WITH_INTERRUPT */
|
|
|
|
#if RX_WITH_DMA
|
|
#define RXBUFSIZE 128
|
|
|
|
static uint8_t rxbuf[RXBUFSIZE];
|
|
static uint16_t last_size;
|
|
static struct ctimer rxdma_timer;
|
|
|
|
static void
|
|
handle_rxdma_timer(void *ptr)
|
|
{
|
|
uint16_t size;
|
|
size = DMA0SZ; /* Note: loop requires that size is less or eq to RXBUFSIZE */
|
|
while(last_size != size) {
|
|
uart0_input_handler((unsigned char)rxbuf[RXBUFSIZE - last_size]);
|
|
last_size--;
|
|
if(last_size == 0) {
|
|
last_size = RXBUFSIZE;
|
|
}
|
|
}
|
|
|
|
ctimer_reset(&rxdma_timer);
|
|
}
|
|
#endif /* RX_WITH_DMA */
|
|
|
|
/*---------------------------------------------------------------------------*/
|
|
uint8_t
|
|
uart0_active(void)
|
|
{
|
|
return (UCA0STAT & UCBUSY) | transmitting;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
void
|
|
uart0_set_input(int (*input)(unsigned char c))
|
|
{
|
|
#if RX_WITH_DMA /* This needs to be called after ctimer process is started */
|
|
ctimer_set(&rxdma_timer, CLOCK_SECOND / 64, handle_rxdma_timer, NULL);
|
|
#endif
|
|
uart0_input_handler = input;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
void
|
|
uart0_writeb(unsigned char c)
|
|
{
|
|
watchdog_periodic();
|
|
#if TX_WITH_INTERRUPT
|
|
/* Put the outgoing byte on the transmission buffer. If the buffer
|
|
is full, we just keep on trying to put the byte into the buffer
|
|
until it is possible to put it there. */
|
|
while(ringbuf_put(&txbuf, c) == 0);
|
|
|
|
/* If there is no transmission going, we need to start it by putting
|
|
the first byte into the UART. */
|
|
if(transmitting == 0) {
|
|
transmitting = 1;
|
|
UCA0TXBUF = ringbuf_get(&txbuf);
|
|
}
|
|
|
|
#else /* TX_WITH_INTERRUPT */
|
|
|
|
/* Loop until the transmission buffer is available. */
|
|
/*Enric while((IFG2 & UCA0TXIFG) == 0); */
|
|
while((UCA0STAT & UCBUSY));
|
|
|
|
/* Transmit the data. */
|
|
UCA0TXBUF = c;
|
|
#endif /* TX_WITH_INTERRUPT */
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
#if !NETSTACK_CONF_WITH_IPV4 /* If NETSTACK_CONF_WITH_IPV4 is defined, putchar() is defined by the SLIP driver */
|
|
#endif /* ! NETSTACK_CONF_WITH_IPV4 */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* Initalize the RS232 port.
|
|
*
|
|
*/
|
|
void
|
|
uart0_init(unsigned long ubr)
|
|
{
|
|
/* RS232 */
|
|
UCA0CTL1 |= UCSWRST; /* Hold peripheral in reset state */
|
|
UCA0CTL1 |= UCSSEL_2; /* CLK = SMCLK */
|
|
|
|
UCA0BR0 = ubr; /* 8MHz/115200 = 69 = 0x45 */
|
|
UCA0BR1 = 0x00;
|
|
UCA0MCTL = UCBRS_3; /* Modulation UCBRSx = 3 */
|
|
|
|
P3DIR &= ~0x20; /* P3.5 = USCI_A0 RXD as input */
|
|
P3DIR |= 0x10; /* P3.4 = USCI_A0 TXD as output */
|
|
P3SEL |= 0x30; /* P3.4,5 = USCI_A0 TXD/RXD */
|
|
/*UCA0CTL1 &= ~UCSWRST;*/ /* Initialize USCI state machine */
|
|
|
|
transmitting = 0;
|
|
|
|
/* XXX Clear pending interrupts before enable */
|
|
IFG2 &= ~UCA0RXIFG;
|
|
IFG2 &= ~UCA0TXIFG;
|
|
UCA0CTL1 &= ~UCSWRST; /* Initialize USCI state machine **before** enabling interrupts */
|
|
IE2 |= UCA0RXIE; /* Enable UCA0 RX interrupt */
|
|
/* Enable USCI_A0 TX interrupts (if TX_WITH_INTERRUPT enabled) */
|
|
#if TX_WITH_INTERRUPT
|
|
ringbuf_init(&txbuf, txbuf_data, sizeof(txbuf_data));
|
|
IE2 |= UCA0TXIE; /* Enable UCA0 TX interrupt */
|
|
#endif /* TX_WITH_INTERRUPT */
|
|
|
|
#if RX_WITH_DMA
|
|
IE2 &= ~UCA0RXIE; /* disable USART0 RX interrupt */
|
|
/* UART0_RX trigger */
|
|
DMACTL0 = DMA0TSEL_3;
|
|
|
|
/* source address = UCA0RXBUF */
|
|
DMA0SA = (unsigned int)&UCA0RXBUF;
|
|
DMA0DA = (unsigned int)&rxbuf;
|
|
DMA0SZ = RXBUFSIZE;
|
|
last_size = RXBUFSIZE;
|
|
DMA0CTL = DMADT_4 + DMASBDB + DMADSTINCR_3 + DMAEN + DMAREQ;
|
|
|
|
msp430_add_lpm_req(MSP430_REQUIRE_LPM1);
|
|
#endif /* RX_WITH_DMA */
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
#if !RX_WITH_DMA
|
|
ISR(USCIAB0RX, uart0_rx_interrupt)
|
|
{
|
|
uint8_t c;
|
|
|
|
ENERGEST_ON(ENERGEST_TYPE_IRQ);
|
|
if(UCA0STAT & UCRXERR) {
|
|
c = UCA0RXBUF; /* Clear error flags by forcing a dummy read. */
|
|
} else {
|
|
c = UCA0RXBUF;
|
|
if(uart0_input_handler != NULL) {
|
|
if(uart0_input_handler(c)) {
|
|
LPM4_EXIT;
|
|
}
|
|
}
|
|
}
|
|
ENERGEST_OFF(ENERGEST_TYPE_IRQ);
|
|
}
|
|
#endif /* !RX_WITH_DMA */
|
|
/*---------------------------------------------------------------------------*/
|
|
#if TX_WITH_INTERRUPT
|
|
ISR(USCIAB0TX, uart0_tx_interrupt)
|
|
{
|
|
ENERGEST_ON(ENERGEST_TYPE_IRQ);
|
|
if((IFG2 & UCA0TXIFG)) {
|
|
|
|
if(ringbuf_elements(&txbuf) == 0) {
|
|
transmitting = 0;
|
|
} else {
|
|
UCA0TXBUF = ringbuf_get(&txbuf);
|
|
}
|
|
}
|
|
|
|
/* In a stand-alone app won't work without this. Is the UG misleading? */
|
|
IFG2 &= ~UCA0TXIFG;
|
|
|
|
ENERGEST_OFF(ENERGEST_TYPE_IRQ);
|
|
}
|
|
#endif /* TX_WITH_INTERRUPT */
|
|
/*---------------------------------------------------------------------------*/
|