ab1491be69
Switch to CMSIS-CORE and remove the duplicate code. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
497 lines
19 KiB
C
497 lines
19 KiB
C
/*
|
|
* Copyright (c) 2012, Texas Instruments Incorporated - http://www.ti.com/
|
|
* Copyright (c) 2015, Zolertia
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
/**
|
|
* \addtogroup zoul-platforms
|
|
* @{
|
|
*
|
|
* \defgroup remote-reva RE-Mote platform revision A
|
|
*
|
|
* The RE-Mote was designed jointly with universities and industry partners in
|
|
* RERUM European project, to ease the development of private and secure
|
|
* applications for IoT and Smart City applications. The RE-Mote packs several
|
|
* on-board resources, like a RTC, external WDT, Micro-SD, RF switch and a
|
|
* Shutdown mode to reduce its power consumption down to 300nA.
|
|
*
|
|
* This file provides connectivity information on LEDs, Buttons, UART and
|
|
* other RE-Mote revision A peripherals
|
|
*
|
|
* This file can be used as the basis to configure other platforms using the
|
|
* cc2538 SoC.
|
|
* @{
|
|
*
|
|
* \file
|
|
* Header file with definitions related to the I/O connections on the Zolertia's
|
|
* RE-Mote platform (revision A), cc2538-based
|
|
*
|
|
* \note Do not include this file directly. It gets included by contiki-conf
|
|
* after all relevant directives have been set.
|
|
*/
|
|
#ifndef BOARD_H_
|
|
#define BOARD_H_
|
|
|
|
#include "dev/gpio.h"
|
|
#include "dev/nvic.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name Connector headers
|
|
*
|
|
* The RE-Mote features two 2.54 mm header rows over which exposes the following
|
|
* pins (facing up, Zolertia/RERUM logo above, buttons and micro USB at bottom):
|
|
* ----------------------+---+---+---------------------------------------------
|
|
* PIN_NAME |JP6|JP5| PIN_NAME
|
|
* ----------------------+---+---+---------------------------------------------
|
|
* LED1/EXT_WDT/PD5 |-01|18-| PC6/SPI1.MISO/USD.MISO
|
|
* LED2/UART1.CTS/PD4 |-02|17-| PC5/SPI1.MOSI/USD.MOSI
|
|
* LED3/UART1.RTS/PD3 |-03|16-| PC4/SPI1.SCLK/USD.SCLK
|
|
* UART0.RX/PA0 |-04|15-| PA3/BUTTON.USER
|
|
* UART0.TX/PA1 |-05|14-| RESET/JTAG.RESET/BUTTON.RESET
|
|
* SHUTDOWN_ENABLE/PD1 |-06|13-| DGND
|
|
* RTC.SDA/I2C.SDA/PC2 |-07|12-| D+3.3
|
|
* RTC.SCL/I2C.SCL/PC3 |-08|11-| PA5/AIN5/ADC1
|
|
* DGND |-09|10-| PA4/RTC_INT1/AIN4/ADC2
|
|
* D+3.3 |-10|09-| DGND
|
|
* USD.CS/AIN7/PA7 |-11|08-| D+5.1
|
|
* SHUTDOWN_DONE/PD0 |-12|07-| PA2/AIN2/ADC3
|
|
* UART1.RX/PC1 |-13|06-| JTAG.TMS
|
|
* UART1.TX/PC0 |-14|05-| JTAG.TCK
|
|
* DGND |-15|04-| PB7/JTAG.TDO
|
|
* D+3.3 |-16|03-| PB6/JTAG.TDI
|
|
* DGND |-17|02-| PS+EXT
|
|
* +VBAT |-18|01-| DGND
|
|
* ----------------------+---+---+---------------------------------------------
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name RE-Mote LED configuration
|
|
*
|
|
* LEDs on the RE-Mote are connected as follows:
|
|
* - LED1 (Red) -> PD5
|
|
* - LED2 (Green) -> PD4
|
|
* - LED3 (Blue) -> PD3
|
|
*
|
|
* LED1 pin shared with EXT_WDT and exposed in JP6 connector
|
|
* LED2 pin shared with UART1 CTS, pin exposed in JP6 connector
|
|
* LED3 pin shared with UART1 RTS, exposed in JP6 connector
|
|
* @{
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
/* Some files include leds.h before us, so we need to get rid of defaults in
|
|
* leds.h before we provide correct definitions */
|
|
#undef LEDS_GREEN
|
|
#undef LEDS_YELLOW
|
|
#undef LEDS_BLUE
|
|
#undef LEDS_RED
|
|
#undef LEDS_CONF_ALL
|
|
|
|
/* In leds.h the LEDS_BLUE is defined by LED_YELLOW definition */
|
|
#define LEDS_GREEN (1 << 4) /**< LED1 (Green) -> PD4 */
|
|
#define LEDS_BLUE (1 << 3) /**< LED2 (Blue) -> PD3 */
|
|
#define LEDS_RED (1 << 5) /**< LED3 (Red) -> PD5 */
|
|
|
|
#define LEDS_CONF_ALL (LEDS_GREEN | LEDS_BLUE | LEDS_RED)
|
|
|
|
#define LEDS_LIGHT_BLUE (LEDS_GREEN | LEDS_BLUE) /**< Green + Blue (24) */
|
|
#define LEDS_YELLOW (LEDS_GREEN | LEDS_RED) /**< Green + Red (48) */
|
|
#define LEDS_PURPLE (LEDS_BLUE | LEDS_RED) /**< Blue + Red (40) */
|
|
#define LEDS_WHITE LEDS_ALL /**< Green + Blue + Red (56) */
|
|
|
|
/* Notify various examples that we have LEDs */
|
|
#define PLATFORM_HAS_LEDS 1
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name USB configuration
|
|
*
|
|
* The USB pullup is enabled by an external resistor, not mapped to a GPIO
|
|
*/
|
|
#ifdef USB_PULLUP_PORT
|
|
#undef USB_PULLUP_PORT
|
|
#endif
|
|
#ifdef USB_PULLUP_PIN
|
|
#undef USB_PULLUP_PIN
|
|
#endif
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name UART configuration
|
|
*
|
|
* On the RE-Mote, the UARTs are connected to the following ports/pins:
|
|
*
|
|
* - UART0:
|
|
* - RX: PA0, connected to CP2104 serial-to-usb converter TX pin
|
|
* - TX: PA1, connected to CP2104 serial-to-usb converter RX pin
|
|
* - UART1:
|
|
* - RX: PC1
|
|
* - TX: PC0
|
|
* - CTS: PD4, shared with LED2 (Green), disabled as default
|
|
* - RTS: PD3, shared with LED3 (Blue), disabled as default
|
|
*
|
|
* We configure the port to use UART0 and UART1, CTS/RTS only for UART1,
|
|
* both without a HW pull-up resistor
|
|
* UART0 and UART1 pins are exposed over the JP6 connector
|
|
* @{
|
|
*/
|
|
#define UART0_RX_PORT GPIO_A_NUM
|
|
#define UART0_RX_PIN 0
|
|
#define UART0_TX_PORT GPIO_A_NUM
|
|
#define UART0_TX_PIN 1
|
|
|
|
#define UART1_RX_PORT GPIO_C_NUM
|
|
#define UART1_RX_PIN 1
|
|
#define UART1_TX_PORT GPIO_C_NUM
|
|
#define UART1_TX_PIN 0
|
|
#define UART1_CTS_PORT (-1)
|
|
#define UART1_CTS_PIN (-1)
|
|
#define UART1_RTS_PORT (-1)
|
|
#define UART1_RTS_PIN (-1)
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name ADC configuration
|
|
*
|
|
* These values configure which CC2538 pins and ADC channels to use for the ADC
|
|
* inputs. By default the RE-Mote allows two out-of-the-box ADC ports with a
|
|
* phidget-like 3-pin connector (GND/VDD/ADC)
|
|
*
|
|
* The RE-Mote allows both 3.3V and 5V analogue sensors as follow:
|
|
*
|
|
* - ADC1: up to 3.3V.
|
|
* - ADC2: up to 3.3V, shared with RTC_INT
|
|
* - ADC3: up to 5V, by means of a 2/3 voltage divider.
|
|
*
|
|
* Also there are other ADC channels shared by default with Micro SD card and
|
|
* user button implementations:
|
|
* - ADC4: up to 3.3V.
|
|
* - ADC5: up to 3.3V.
|
|
* - ADC6: up to 3.3V.
|
|
*
|
|
* ADC inputs can only be on port A.
|
|
* All ADCx are exposed in JP5 connector, but only ADC1 and ADC3 have GND and
|
|
* VDD (3/5V) pins next to it, so these can be exposed into a 3-pin phidget-like
|
|
* connector, for ADC2 either solder a wire to connect, or use a 4-pin connector
|
|
* to expose both ADC1 and ADC2 in a single connector, but this will leave no
|
|
* space for a ADC3 connector.
|
|
* The internal ADC reference is 1190mV, use either a voltage divider as input,
|
|
* or a different voltage reference, like AVDD5 or other externally (AIN7), but
|
|
* note the PA7 is shared with the Micro-SD CSn pin, likewise for PA6 (AIN6)
|
|
* shared witht the Micro-SD select pin
|
|
* To use the ADC2 pin, remove the resistor on the Zoul's PA4 pin (JP1, pin 10)
|
|
* and enable below (replace -1 with 4).
|
|
* @{
|
|
*/
|
|
#define ADC_SENSORS_PORT GPIO_A_NUM /**< ADC GPIO control port */
|
|
|
|
#ifndef ADC_SENSORS_CONF_ADC1_PIN
|
|
#define ADC_SENSORS_ADC1_PIN 5 /**< ADC1 to PA5, 3V3 */
|
|
#else
|
|
#if ((ADC_SENSORS_CONF_ADC1_PIN != -1) && (ADC_SENSORS_CONF_ADC1_PIN != 5))
|
|
#error "ADC1 channel should be mapped to PA5 or disabled with -1"
|
|
#else
|
|
#define ADC_SENSORS_ADC1_PIN ADC_SENSORS_CONF_ADC1_PIN
|
|
#endif
|
|
#endif
|
|
|
|
#ifndef ADC_SENSORS_CONF_ADC3_PIN
|
|
#define ADC_SENSORS_ADC3_PIN 2 /**< ADC3 to PA2, 5V */
|
|
#else
|
|
#if ((ADC_SENSORS_CONF_ADC3_PIN != -1) && (ADC_SENSORS_CONF_ADC3_PIN != 2))
|
|
#error "ADC3 channel should be mapped to PA2 or disabled with -1"
|
|
#else
|
|
#define ADC_SENSORS_ADC3_PIN ADC_SENSORS_CONF_ADC3_PIN
|
|
#endif
|
|
#endif
|
|
|
|
#ifndef ADC_SENSORS_CONF_ADC2_PIN
|
|
#define ADC_SENSORS_ADC2_PIN (-1) /**< ADC2 no declared */
|
|
#else
|
|
#define ADC_SENSORS_ADC2_PIN 4 /**< Hard-coded to PA4 */
|
|
#endif
|
|
|
|
#ifndef ADC_SENSORS_CONF_ADC4_PIN
|
|
#define ADC_SENSORS_ADC4_PIN (-1) /**< ADC4 not declared */
|
|
#else
|
|
#define ADC_SENSORS_ADC4_PIN 6 /**< Hard-coded to PA6 */
|
|
#endif
|
|
|
|
#ifndef ADC_SENSORS_CONF_ADC5_PIN
|
|
#define ADC_SENSORS_ADC5_PIN (-1) /**< ADC5 not declared */
|
|
#else
|
|
#define ADC_SENSORS_ADC5_PIN 7 /**< Hard-coded to PA7 */
|
|
#endif
|
|
|
|
#ifndef ADC_SENSORS_CONF_ADC6_PIN
|
|
#define ADC_SENSORS_ADC6_PIN (-1) /**< ADC6 not declared */
|
|
#else
|
|
#define ADC_SENSORS_ADC6_PIN 3 /**< Hard-coded to PA3 */
|
|
#endif
|
|
|
|
#ifndef ADC_SENSORS_CONF_MAX
|
|
#define ADC_SENSORS_MAX 2 /**< Maximum sensors */
|
|
#else
|
|
#define ADC_SENSORS_MAX ADC_SENSORS_CONF_MAX
|
|
#endif
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name RE-Mote Button configuration
|
|
*
|
|
* Buttons on the RE-Mote are connected as follows:
|
|
* - BUTTON_USER -> PA3, S1 user button, shared with bootloader and RTC_INT1
|
|
* - BUTTON_RESET -> RESET_N line, S2 reset both CC2538 and CoP
|
|
* - BUTTON_PIC1W -> shared with SHUTDOWN_ENABLE, not mounted.
|
|
* @{
|
|
*/
|
|
/** BUTTON_USER -> PA3 */
|
|
#define BUTTON_USER_PORT GPIO_A_NUM
|
|
#define BUTTON_USER_PIN 3
|
|
#define BUTTON_USER_VECTOR GPIO_A_IRQn
|
|
|
|
/* Notify various examples that we have an user button.
|
|
* If ADC6 channel is used, then disable the user button
|
|
*/
|
|
#ifdef PLATFORM_CONF_WITH_BUTTON
|
|
#if (PLATFORM_CONF_WITH_BUTTON && (ADC_SENSORS_ADC6_PIN == 3))
|
|
#error "The ADC6 (PA3) and user button cannot be enabled at the same time"
|
|
#else
|
|
#define PLATFORM_HAS_BUTTON (PLATFORM_CONF_WITH_BUTTON && \
|
|
!(ADC_SENSORS_ADC6_PIN == 3))
|
|
#endif /* (PLATFORM_CONF_WITH_BUTTON && (ADC_SENSORS_ADC6_PIN == 3)) */
|
|
#else
|
|
#define PLATFORM_HAS_BUTTON !(ADC_SENSORS_ADC6_PIN == 3)
|
|
#endif /* PLATFORM_CONF_WITH_BUTTON */
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name SPI (SSI0) configuration
|
|
*
|
|
* These values configure which CC2538 pins to use for the SPI (SSI0) lines,
|
|
* reserved exclusively for the CC1200 RF transceiver. These pins are not
|
|
* exposed to any connector, and should be avoid to use it.
|
|
* TX -> MOSI, RX -> MISO
|
|
* @{
|
|
*/
|
|
#define SPI0_CLK_PORT GPIO_B_NUM
|
|
#define SPI0_CLK_PIN 2
|
|
#define SPI0_TX_PORT GPIO_B_NUM
|
|
#define SPI0_TX_PIN 1
|
|
#define SPI0_RX_PORT GPIO_B_NUM
|
|
#define SPI0_RX_PIN 3
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name SPI (SSI1) configuration
|
|
*
|
|
* These values configure which CC2538 pins to use for the SPI (SSI1) lines,
|
|
* shared with the microSD and exposed over JP5 connector.
|
|
* It is advisable to use a CSn pin other than the Micro-SD's.
|
|
* TX -> MOSI, RX -> MISO
|
|
* @{
|
|
*/
|
|
#define SPI1_CLK_PORT GPIO_C_NUM
|
|
#define SPI1_CLK_PIN 4
|
|
#define SPI1_TX_PORT GPIO_C_NUM
|
|
#define SPI1_TX_PIN 5
|
|
#define SPI1_RX_PORT GPIO_C_NUM
|
|
#define SPI1_RX_PIN 6
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name I2C configuration
|
|
*
|
|
* These values configure which CC2538 pins to use for the I2C lines, exposed
|
|
* over JP6 connector, also available as testpoints T2 (PC2) and T3 (PC3).
|
|
* The I2C bus is shared with the on-board RTC.
|
|
* The I2C is exposed over the JP6 header, using a 5-pin connector with 2.54 mm
|
|
* spacing, providing also D+3.3V, GND and a generic pin that can be used as an
|
|
* interrupt pin
|
|
* @{
|
|
*/
|
|
#define I2C_SCL_PORT GPIO_C_NUM
|
|
#define I2C_SCL_PIN 3
|
|
#define I2C_SDA_PORT GPIO_C_NUM
|
|
#define I2C_SDA_PIN 2
|
|
#define I2C_INT_PORT GPIO_D_NUM
|
|
#define I2C_INT_PIN 1
|
|
#define I2C_INT_VECTOR GPIO_D_IRQn
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name Antenna switch configuration
|
|
*
|
|
* These values configure the required pin to drive the RF antenna switch, to
|
|
* either enable the sub-1Ghz RF interface (power-up the CC1200) or the 2.4GHz
|
|
* RF interface of the CC2538, both alternatively routed to a RP-SMA connector
|
|
* to allow using an external antenna for both cases.
|
|
*
|
|
* Note it is also possible to enable both RF interfaces at the same time, by
|
|
* switching On the sub-1GHz RF interface, and placing an 0Ohm resistor (R19),
|
|
* to select between using a ceramic chip antenna (not mounted), or to connect
|
|
* and external antenna over a pigtail to the U.Fl connector (not mounted).
|
|
*
|
|
* RF switch state:
|
|
* - LOW: 2.4GHz RF interface on RP-SMA connector, CC1200 powered-off.
|
|
* - HIGH: Sub-1GHz RF interface on RP-SMA connector.
|
|
* @{
|
|
*/
|
|
#define ANTENNA_RF_SW_PORT GPIO_D_NUM
|
|
#define ANTENNA_RF_SW_PIN 2
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name Dual RF interface support
|
|
*
|
|
* Enables support for dual band operation (both CC1200 and 2.4GHz enabled).
|
|
* The driver checks the selected Radio stack, and forces the antenna switch to
|
|
* either position. Enabling the definition below forces to skip this check.
|
|
* @{
|
|
*/
|
|
#define REMOTE_DUAL_RF_ENABLED 0
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name CC1200 configuration
|
|
*
|
|
* These values configure the required pins to drive the CC1200
|
|
* None of the following pins are exposed to any connector, kept for internal
|
|
* use only
|
|
* @{
|
|
*/
|
|
#define CC1200_SPI_INSTANCE 0
|
|
#define CC1200_SPI_SCLK_PORT SPI0_CLK_PORT
|
|
#define CC1200_SPI_SCLK_PIN SPI0_CLK_PIN
|
|
#define CC1200_SPI_MOSI_PORT SPI0_TX_PORT
|
|
#define CC1200_SPI_MOSI_PIN SPI0_TX_PIN
|
|
#define CC1200_SPI_MISO_PORT SPI0_RX_PORT
|
|
#define CC1200_SPI_MISO_PIN SPI0_RX_PIN
|
|
#define CC1200_SPI_CSN_PORT GPIO_B_NUM
|
|
#define CC1200_SPI_CSN_PIN 5
|
|
#define CC1200_GDO0_PORT GPIO_B_NUM
|
|
#define CC1200_GDO0_PIN 4
|
|
#define CC1200_GDO2_PORT GPIO_B_NUM
|
|
#define CC1200_GDO2_PIN 0
|
|
#define CC1200_RESET_PORT GPIO_C_NUM
|
|
#define CC1200_RESET_PIN 7
|
|
#define CC1200_GPIOx_VECTOR GPIO_B_IRQn
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name microSD configuration
|
|
*
|
|
* These values configure the required pins to drive the built-in microSD
|
|
* external module, to be used with SSI1
|
|
* @{
|
|
*/
|
|
#define USD_CLK_PORT SPI1_CLK_PORT
|
|
#define USD_CLK_PIN SPI1_CLK_PIN
|
|
#define USD_MOSI_PORT SPI1_TX_PORT
|
|
#define USD_MOSI_PIN SPI1_TX_PIN
|
|
#define USD_MISO_PORT SPI1_RX_PORT
|
|
#define USD_MISO_PIN SPI1_RX_PIN
|
|
#define USD_CSN_PORT GPIO_A_NUM
|
|
#define USD_CSN_PIN 7
|
|
#define USD_SEL_PORT GPIO_A_NUM
|
|
#define USD_SEL_PIN 6
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name Power management and shutdown mode
|
|
*
|
|
* The shutdown mode is an ultra-low power operation mode that effectively
|
|
* powers-down the entire RE-Mote (CC2538, CC1200, attached sensors, etc) and
|
|
* only keeps running a power gating timer (NanoTimer), the on-board RTC and
|
|
* an ultra-low power consumption MCU (PIC12F635). The Shutdown mode allows:
|
|
*
|
|
* - Put the RE-Mote in an ultra-low power sleep (shutdown) drawing <200nA avg.
|
|
* - Periodically awake and execute tasks, being the shutdown period selectable
|
|
* via R47 resistor value (22KOhm as default for 1 minute shutdown period).
|
|
* - Enter shutdown mode before the shutdown period expiration, by invoking the
|
|
* PM_SHUTDOWN_NOW macrp
|
|
*
|
|
* The shutdown mode can be disabled by hardware by short-circuiting or placing
|
|
* an 0Ohm resistor across W1 pad.
|
|
* @{
|
|
*/
|
|
#define PM_DONE_PORT GPIO_D_NUM
|
|
#define PM_DONE_PIN 0
|
|
#define PM_CMD_PORT GPIO_D_NUM
|
|
#define PM_CMD_PIN 1
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name On-board RTC
|
|
*
|
|
* The shutdown mode can be disabled by hardware by short-circuiting or placing
|
|
* an 0Ohm resistor across W1 pad. As the RTC_INT1 pin is also shared with the
|
|
* BUTTON_USER, so either disable or not use the user button, or upon receiving
|
|
* an interrupt, poll the RTC.
|
|
*
|
|
* The RTC_INT1 can be used to exit the CC2538's LPM3 mode.
|
|
* A second interruption pin is connected to the PIC12F635, for applications
|
|
* requiring to put the PIC into deep-sleep and waking up at a certain time.
|
|
* @{
|
|
*/
|
|
#define RTC_SDA_PORT I2C_SDA_PORT
|
|
#define RTC_SDA_PIN I2C_SDA_PIN
|
|
#define RTC_SCL_PORT I2C_SCL_PORT
|
|
#define RTC_SCL_PIN I2C_SCL_PIN
|
|
#define RTC_INT1_PORT GPIO_A_NUM
|
|
#define RTC_INT1_PIN 4
|
|
#define RTC_INT1_VECTOR GPIO_A_IRQn
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name On-board external WDT
|
|
* The RE-Mote features an on-board external WDT and battery monitor, which
|
|
* adds more robustness and prevents the mote to run wild if any unexpected
|
|
* problem shows-up.
|
|
* The external WDT requires a short pulse (<1ms) to be sent before a 2-second
|
|
* period. The battery monitor keeps the device in Reset if the voltage input
|
|
* is lower than 2.5V.
|
|
* The external WDT can be disabled by removing the R40 0Ohm resistor.
|
|
* The EXT_WDT pin is shared with LED1 (Red). For long-time operation, it is
|
|
* advised to remove R14 resistor to disable LED1.
|
|
* As default the Texas Instrument's TPS3823 WDT is not mounted.
|
|
* @{
|
|
*/
|
|
#define EXT_WDT_PORT GPIO_D_NUM
|
|
#define EXT_WDT_PIN 5
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name Device string used on startup
|
|
* @{
|
|
*/
|
|
#define BOARD_STRING "Zolertia RE-Mote revision A platform"
|
|
/** @} */
|
|
|
|
#endif /* BOARD_H_ */
|
|
|
|
/**
|
|
* @}
|
|
* @}
|
|
*/
|