nes-proj/platform/avr-ravenusb/contiki-conf.h

476 lines
19 KiB
C

/*
* Copyright (c) 2006, Technical University of Munich
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the Institute nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* This file is part of the Contiki operating system.
*
* @(#)$$
*/
/**
* \file
* Configuration for RZRAVEN USB stick "jackdaw"
*
* \author
* Simon Barner <barner@in.tum.de>
* David Kopf <dak664@embarqmail.com>
*/
#ifndef CONTIKI_CONF_H_
#define CONTIKI_CONF_H_
/* ************************************************************************** */
//#pragma mark Basic Configuration
/* ************************************************************************** */
/* Platform name, type, and MCU clock rate */
#define PLATFORM_NAME "RAVENUSB"
#define PLATFORM_TYPE RAVENUSB_C
#ifndef F_CPU
#define F_CPU 8000000UL
#endif
#include <stdbool.h>
#include <stdint.h>
#include <string.h>
#include <avr/eeprom.h>
/* Skip the last four bytes of the EEPROM, to leave room for things
* like the avrdude erase count and bootloader signaling. */
#define EEPROM_CONF_SIZE ((E2END + 1) - 4)
/* The AVR tick interrupt usually is done with an 8 bit counter around 128 Hz.
* 125 Hz needs slightly more overhead during the interrupt, as does a 32 bit
* clock_time_t.
*/
/* Clock ticks per second */
#define CLOCK_CONF_SECOND 125
typedef uint32_t clock_time_t;
#define CLOCK_LT(a,b) ((int32_t)((a)-(b)) < 0)
/* These routines are not part of the contiki core but can be enabled in cpu/avr/clock.c */
void clock_delay_msec(uint16_t howlong);
void clock_adjust_ticks(clock_time_t howmany);
/* Use EEPROM settings manager, or hard-coded EEPROM reads? */
/* Generate random MAC address on first startup? */
/* Random number from radio clock skew or ADC noise? */
#define JACKDAW_CONF_USE_SETTINGS 0
#define JACKDAW_CONF_RANDOM_MAC 0
#define RNG_CONF_USE_RADIO_CLOCK 1
//#define RNG_CONF_USE_ADC 1
/* COM port to be used for SLIP connection. Not tested on Jackdaw. */
#define SLIP_PORT RS232_PORT_0
/* Pre-allocated memory for loadable modules heap space (in bytes)*/
/* Default is 4096. Currently used only when elfloader is present. Not tested on Jackdaw */
//#define MMEM_CONF_SIZE 256
/* Starting address for code received via the codeprop facility. Not tested on Jackdaw */
typedef unsigned long off_t;
//#define EEPROMFS_ADDR_CODEPROP 0x8000
/* Simple stack monitor. Status is displayed from the USB menu with 'm' command */
#define CONFIG_STACK_MONITOR 1
/* RADIO_CONF_CALIBRATE_INTERVAL is used in rf230bb and clock.c. If nonzero a 256 second interval is used */
/* Calibration is automatic when the radio wakes so is not necessary when the radio periodically sleeps */
//#define RADIO_CONF_CALIBRATE_INTERVAL 256
/* RADIOSTATS is used in rf230bb, clock.c and the webserver cgi to report radio usage */
//#define RADIOSTATS 1
/* Possible watchdog timeouts depend on mcu. Default is WDTO_2S. -1 Disables the watchdog. */
//#define WATCHDOG_CONF_TIMEOUT -1
/* ************************************************************************** */
//#pragma mark USB Ethernet Hooks
/* ************************************************************************** */
#ifndef USB_ETH_HOOK_IS_READY_FOR_INBOUND_PACKET
#if RF230BB
#define USB_ETH_HOOK_IS_READY_FOR_INBOUND_PACKET() rf230_is_ready_to_send()
#else
static inline uint8_t radio_is_ready_to_send_() {
switch(radio_get_trx_state()) {
case BUSY_TX:
case BUSY_TX_ARET:
return 0;
}
return 1;
}
#define USB_ETH_HOOK_IS_READY_FOR_INBOUND_PACKET() radio_is_ready_to_send_()
#endif
#endif
#ifndef USB_ETH_HOOK_HANDLE_INBOUND_PACKET
#define USB_ETH_HOOK_HANDLE_INBOUND_PACKET(buffer,len) do { uip_len = len ; mac_ethernetToLowpan(buffer); } while(0)
#endif
#ifndef USB_ETH_HOOK_SET_PROMISCIOUS_MODE
#if RF230BB
#define USB_ETH_HOOK_SET_PROMISCIOUS_MODE(value) rf230_set_promiscuous_mode(value)
#else
#define USB_ETH_HOOK_SET_PROMISCIOUS_MODE(value) radio_set_trx_state(value?RX_ON:RX_AACK_ON)
#endif
#endif
#ifndef USB_ETH_HOOK_INIT
#define USB_ETH_HOOK_INIT() mac_ethernetSetup()
#endif
/* ************************************************************************** */
//#pragma mark RF230BB Hooks
/* ************************************************************************** */
//#define RF230BB_HOOK_RADIO_OFF() Led1_off()
//#define RF230BB_HOOK_RADIO_ON() Led1_on()
#define RF230BB_HOOK_TX_PACKET(buffer,total_len) mac_log_802_15_4_tx(buffer,total_len)
#define RF230BB_HOOK_RX_PACKET(buffer,total_len) mac_log_802_15_4_rx(buffer,total_len)
#define RF230BB_HOOK_IS_SEND_ENABLED() mac_is_send_enabled()
extern bool mac_is_send_enabled(void);
extern void mac_log_802_15_4_tx(const uint8_t* buffer, size_t total_len);
extern void mac_log_802_15_4_rx(const uint8_t* buffer, size_t total_len);
/* ************************************************************************** */
//#pragma mark USB CDC-ACM (UART) Hooks
/* ************************************************************************** */
#define USB_CDC_ACM_HOOK_TX_END(char) vcptx_end_led()
#define USB_CDC_ACM_HOOK_CLS_CHANGED(state) vcptx_end_led()
#define USB_CDC_ACM_HOOK_CONFIGURED() vcptx_end_led()
/* ************************************************************************** */
//#pragma mark Serial Port Settings
/* ************************************************************************** */
/* Set USB_CONF_MACINTOSH to prefer CDC-ECM+DEBUG enumeration for Mac/Linux
* Leave undefined to prefer RNDIS+DEBUG enumeration for Windows/Linux
* TODO:Serial port would enumerate in all cases and prevent falling through to
* the supported network interface if USB_CONF_MACINTOSH is used with Windows
* or vice versa. The Mac configuration is set up to still enumerate as RNDIS-ONLY
* on Windows (without the serial port).
* At present the Windows configuration will not enumerate on the Mac at all,
* since it wants a custom descriptor for USB composite devices.
*/
#define USB_CONF_MACINTOSH 0
/* Set USB_CONF_SERIAL to enable the USB serial port that allows control of the
* run-time configuration (COMx on Windows, ttyACMx on Linux, tty.usbmodemx on Mac)
* Debug printfs will go to this port unless USB_CONF_RS232 is set.
*/
#define USB_CONF_SERIAL 1
/* RS232 debugs have less effect on network timing and are less likely
* to be dropped due to buffer overflow. Only tx is implemented at present.
* The tx pad is the middle one behind the jackdaw leds.
* RS232 output will work with or without enabling the USB serial port
*/
#define USB_CONF_RS232 1
/* Disable mass storage enumeration for more program space */
//#define USB_CONF_STORAGE 1 /* TODO: Mass storage is currently broken */
/* ************************************************************************** */
//#pragma mark UIP Settings
/* ************************************************************************** */
/* Network setup. The new NETSTACK interface requires RF230BB (as does ip4) */
/* These mostly have no effect when the Jackdaw is a repeater (CONTIKI_NO_NET=1 using fakeuip.c) */
#if NETSTACK_CONF_WITH_IPV6
#define LINKADDR_CONF_SIZE 8
#define UIP_CONF_ICMP6 1
#define UIP_CONF_UDP 1
#define UIP_CONF_TCP 0
#define NETSTACK_CONF_NETWORK sicslowpan_driver
#define SICSLOWPAN_CONF_COMPRESSION SICSLOWPAN_COMPRESSION_HC06
#else
/* ip4 should build but is thoroughly untested */
#define LINKADDR_CONF_SIZE 2
#define NETSTACK_CONF_NETWORK rime_driver
#endif /* NETSTACK_CONF_WITH_IPV6 */
/* See uip-ds6.h */
#define NBR_TABLE_CONF_MAX_NEIGHBORS 2
#define UIP_CONF_DS6_DEFRT_NBU 2
#define UIP_CONF_DS6_PREFIX_NBU 3
#define UIP_CONF_MAX_ROUTES 2
#define UIP_CONF_DS6_ADDR_NBU 3
#define UIP_CONF_DS6_MADDR_NBU 0
#define UIP_CONF_DS6_AADDR_NBU 0
#define UIP_CONF_LL_802154 1
#define UIP_CONF_LLH_LEN 14
#define UIP_CONF_BUFSIZE UIP_LINK_MTU + UIP_LLH_LEN + 4 /* +4 for vlan on macosx */
/* 10 bytes per stateful address context - see sicslowpan.c */
/* Default is 1 context with prefix fd00::/64 */
/* These must agree with all the other nodes or there will be a failure to communicate! */
#//define SICSLOWPAN_CONF_MAX_ADDR_CONTEXTS 1
#define SICSLOWPAN_CONF_ADDR_CONTEXT_0 {addr_contexts[0].prefix[0]=UIP_DS6_DEFAULT_PREFIX_0;addr_contexts[0].prefix[1]=UIP_DS6_DEFAULT_PREFIX_1;}
#define SICSLOWPAN_CONF_ADDR_CONTEXT_1 {addr_contexts[1].prefix[0]=0xbb;addr_contexts[1].prefix[1]=0xbb;}
#define SICSLOWPAN_CONF_ADDR_CONTEXT_2 {addr_contexts[2].prefix[0]=0x20;addr_contexts[2].prefix[1]=0x01;addr_contexts[2].prefix[2]=0x49;addr_contexts[2].prefix[3]=0x78,addr_contexts[2].prefix[4]=0x1d;addr_contexts[2].prefix[5]=0xb1;}
/* 211 bytes per queue buffer */
#define QUEUEBUF_CONF_NUM 8
/* 54 bytes per queue ref buffer */
#define QUEUEBUF_CONF_REF_NUM 2
#define UIP_CONF_MAX_CONNECTIONS 1
#define UIP_CONF_MAX_LISTENPORTS 1
#define UIP_CONF_IP_FORWARD 0
#define UIP_CONF_FWCACHE_SIZE 0
#define UIP_CONF_IPV6_CHECKS 1
#define UIP_CONF_IPV6_QUEUE_PKT 1
#define UIP_CONF_IPV6_REASSEMBLY 0
#define UIP_CONF_UDP_CHECKSUMS 1
#define UIP_CONF_TCP_SPLIT 0
typedef unsigned short uip_stats_t;
#define UIP_CONF_STATISTICS 1
/* Network setup */
#if 1 /* No radio cycling */
#define NETSTACK_CONF_MAC nullmac_driver
#define NETSTACK_CONF_RDC sicslowmac_driver
#define NETSTACK_CONF_FRAMER framer_802154
#define NETSTACK_CONF_RADIO rf230_driver
#define CHANNEL_802_15_4 26
/* If nonzero an interval of 256 seconds is used at present */
#define RADIO_CONF_CALIBRATE_INTERVAL 256
/* AUTOACK receive mode gives better rssi measurements, even if ACK is never requested */
#define RF230_CONF_AUTOACK 1
/* 1 + Number of auto retry attempts 0-15 (0 implies don't use extended TX_ARET_ON mode with CCA) */
#define RF230_CONF_FRAME_RETRIES 2
/* CCA theshold energy -91 to -61 dBm (default -77). Set this smaller than the expected minimum rssi to avoid packet collisions */
/* The Jackdaw menu 'm' command is helpful for determining the smallest ever received rssi */
#define RF230_CONF_CCA_THRES -85
/* Number of CSMA attempts 0-7. 802.15.4 2003 standard max is 5. */
#define RF230_CONF_CSMA_RETRIES 5
/* Allow sneeze command from jackdaw menu. Useful for testing CCA on other radios */
/* During sneezing, any access to an RF230 register will hang the MCU and cause a watchdog reset */
/* The host interface, jackdaw menu and rf230_send routines are temporarily disabled to prevent this */
/* But some calls from an internal uip stack might get through, e.g. from CCA or low power protocols, */
/* as temporarily disabling all the possible accesses would add considerable complication to the radio driver! */
#define RF230_CONF_SNEEZER 1
/* Allow 6loWPAN fragmentation (more efficient for large payloads over a reliable channel) */
#define SICSLOWPAN_CONF_FRAG 1
/* Timeout for fragment reassembly. A reissued browser GET will also cancel reassembly, typically in 2-3 seconds */
#define SICSLOWPAN_CONF_MAXAGE 3
/* Allow sneeze command from jackdaw menu */
#define RF230_CONF_SNEEZE 1
#elif 1 /* Contiki-mac radio cycling */
#define NETSTACK_CONF_MAC nullmac_driver
//#define NETSTACK_CONF_MAC csma_driver
#define NETSTACK_CONF_RDC contikimac_driver
#if NETSTACK_CONF_WITH_IPV6
#define NETSTACK_CONF_FRAMER framer802154
#else /* NETSTACK_CONF_WITH_IPV6 */
#define NETSTACK_CONF_FRAMER contikimac_framer
#endif /* NETSTACK_CONF_WITH_IPV6 */
#define NETSTACK_CONF_RADIO rf230_driver
#define CHANNEL_802_15_4 26
/* Enable extended mode with autoack, but no csma/autoretry */
#define RF230_CONF_FRAME_RETRIES 1
#define RF230_CONF_AUTOACK 1
#define RF230_CONF_CSMA_RETRIES 0
#define SICSLOWPAN_CONF_FRAG 1
#define SICSLOWPAN_CONF_MAXAGE 3
/* Jackdaw has USB power, can be always listening */
#define CONTIKIMAC_CONF_RADIO_ALWAYS_ON 1
#define NETSTACK_CONF_RDC_CHANNEL_CHECK_RATE 8
/* Contiki-mac is a memory hog */
#define PROCESS_CONF_NO_PROCESS_NAMES 1
#undef QUEUEBUF_CONF_NUM
#define QUEUEBUF_CONF_NUM 2
#undef QUEUEBUF_CONF_REF_NUM
#define QUEUEBUF_CONF_REF_NUM 1
#undef UIP_CONF_TCP_SPLIT
#define UIP_CONF_TCP_SPLIT 0
#undef UIP_CONF_STATISTICS
#define UIP_CONF_STATISTICS 0
#undef UIP_CONF_IPV6_QUEUE_PKT
#define UIP_CONF_IPV6_QUEUE_PKT 0
#define UIP_CONF_PINGADDRCONF 0
#define UIP_CONF_LOGGING 0
#undef UIP_CONF_MAX_CONNECTIONS
#define UIP_CONF_MAX_CONNECTIONS 2
#undef UIP_CONF_MAX_LISTENPORTS
#define UIP_CONF_MAX_LISTENPORTS 2
#define UIP_CONF_UDP_CONNS 6
#elif 1 /* cx-mac radio cycling */
#define NETSTACK_CONF_MAC nullmac_driver
//#define NETSTACK_CONF_MAC csma_driver
#define NETSTACK_CONF_RDC cxmac_driver
#define NETSTACK_CONF_FRAMER framer_802154
#define NETSTACK_CONF_RADIO rf230_driver
#define CHANNEL_802_15_4 26
#define RF230_CONF_AUTOACK 1
#define RF230_CONF_FRAME_RETRIES 1
#define SICSLOWPAN_CONF_FRAG 1
#define SICSLOWPAN_CONF_MAXAGE 3
#define CXMAC_CONF_ANNOUNCEMENTS 0
#define NETSTACK_CONF_RDC_CHANNEL_CHECK_RATE 8
#undef QUEUEBUF_CONF_NUM
#define QUEUEBUF_CONF_NUM 8
#undef NBR_TABLE_CONF_MAX_NEIGHBORS
#define NBR_TABLE_CONF_MAX_NEIGHBORS 5
#undef UIP_CONF_MAX_ROUTES
#define UIP_CONF_MAX_ROUTES 5
#else
#error Network configuration not specified!
#endif /* Network setup */
/* ************************************************************************** */
//#pragma mark RPL Settings
/* ************************************************************************** */
#if UIP_CONF_IPV6_RPL
/* Not completely working yet. Works on Ubuntu after $ifconfig usb0 -arp to drop the neighbor solitications */
/* Dropping the NS on other OSs is more complicated, see http://www.sics.se/~adam/wiki/index.php/Jackdaw_RNDIS_RPL_border_router */
/* RPL requires the uip stack. Change #CONTIKI_NO_NET=1 to NETSTACK_CONF_WITH_IPV6=1 in the examples makefile,
or include the needed source files in /plaftorm/avr-ravenusb/Makefile.avr-ravenusb */
/* For the present the buffer_length calcs in rpl-icmp6.c will need adjustment by the length difference
between 6lowpan (0) and ethernet (14) link-layer headers:
// buffer_length = uip_len - uip_l2_l3_icmp_hdr_len;
buffer_length = uip_len - uip_l2_l3_icmp_hdr_len + UIP_LLH_LEN; //Add jackdaw ethernet header
*/
/* Define MAX_*X_POWER to reduce tx power and ignore weak rx packets for testing a miniature multihop network.
* Leave undefined for full power and sensitivity.
* tx=0 (3dbm, default) to 15 (-17.2dbm)
* RF230_CONF_AUTOACK sets the extended mode using the energy-detect register with rx=0 (-91dBm) to 84 (-7dBm)
* else the rssi register is used having range 0 (91dBm) to 28 (-10dBm)
* For simplicity RF230_MIN_RX_POWER is based on the energy-detect value and divided by 3 when autoack is not set.
* On the RF230 a reduced rx power threshold will not prevent autoack if enabled and requested.
* These numbers applied to both Raven and Jackdaw give a maximum communication distance of about 15 cm
* and a 10 meter range to a full-sensitivity RF230 sniffer.
#define RF230_MAX_TX_POWER 15
#define RF230_MIN_RX_POWER 30
*/
#define UIP_CONF_ROUTER 1
#define UIP_CONF_ND6_SEND_RA 0
#define UIP_CONF_ND6_REACHABLE_TIME 600000
#define UIP_CONF_ND6_RETRANS_TIMER 10000
#ifndef RPL_BORDER_ROUTER
#define RPL_BORDER_ROUTER 1
#endif
#define RPL_CONF_STATS 0
#define UIP_CONF_BUFFER_SIZE 1300
//#define NBR_TABLE_CONF_MAX_NEIGHBORS 12
//#define UIP_CONF_MAX_ROUTES 12
#ifdef RPL_BORDER_ROUTER
#undef UIP_FALLBACK_INTERFACE
#define UIP_FALLBACK_INTERFACE rpl_interface
#endif
/* Save all the RAM we can */
#define PROCESS_CONF_NO_PROCESS_NAMES 1
#undef QUEUEBUF_CONF_NUM
#define QUEUEBUF_CONF_NUM 2
#undef QUEUEBUF_CONF_REF_NUM
#define QUEUEBUF_CONF_REF_NUM 1
#undef UIP_CONF_TCP_SPLIT
#define UIP_CONF_TCP_SPLIT 0
#undef UIP_CONF_STATISTICS
#define UIP_CONF_STATISTICS 0
#undef UIP_CONF_IPV6_QUEUE_PKT
#define UIP_CONF_IPV6_QUEUE_PKT 0
#define UIP_CONF_PINGADDRCONF 0
#define UIP_CONF_LOGGING 0
#undef UIP_CONF_MAX_CONNECTIONS
#define UIP_CONF_MAX_CONNECTIONS 2
#undef UIP_CONF_MAX_LISTENPORTS
#define UIP_CONF_MAX_LISTENPORTS 2
#define UIP_CONF_UDP_CONNS 6
/* Optional, TCP needed to serve the RPL neighbor web page currently hard coded at bbbb::200 */
/* The RPL neighbors can also be viewed using the jackdaw menu */
/* A small MSS is adequate for the internal jackdaw webserver and RAM is very limited*/
#define RPL_HTTPD_SERVER 0
#if RPL_HTTPD_SERVER
#undef UIP_CONF_TCP
#define UIP_CONF_TCP 1
#define UIP_CONF_TCP_MSS 48
#define UIP_CONF_RECEIVE_WINDOW 48
#undef NBR_TABLE_CONF_MAX_NEIGHBORS
#define NBR_TABLE_CONF_MAX_NEIGHBORS 5
#undef UIP_CONF_MAX_ROUTES
#define UIP_CONF_MAX_ROUTES 5
#undef UIP_CONF_MAX_CONNECTIONS
#define UIP_CONF_MAX_CONNECTIONS 2
#endif
#define UIP_CONF_ICMP_DEST_UNREACH 1
#define UIP_CONF_DHCP_LIGHT
#undef UIP_CONF_FWCACHE_SIZE
#define UIP_CONF_FWCACHE_SIZE 30
#define UIP_CONF_BROADCAST 1
//#define UIP_ARCH_IPCHKSUM 1
/* Experimental option to pick up a prefix from host interface router advertisements */
/* Requires changes in uip6 and uip-nd6.c to pass link-local RA broadcasts */
/* If this is zero the prefix will be manually set in contiki-raven-main.c */
#define UIP_CONF_ROUTER_RECEIVE_RA 0
#endif /* UIP_CONF_IPV6_RPL */
/* ************************************************************************** */
//#pragma mark Other Settings
/* ************************************************************************** */
/* Use Atmel 'Route Under MAC', currently just in RF230 sniffer mode! */
/* Route-Under-MAC uses 16-bit short addresses */
//#define UIP_CONF_USE_RUM 1
#if UIP_CONF_USE_RUM
#undef UIP_CONF_LL_802154
#define UIP_DATA_RUM_OFFSET 5
#endif /* UIP_CONF_USE_RUM */
#define CCIF
#define CLIF
#endif /* CONTIKI_CONF_H_ */