148 lines
6.1 KiB
C
148 lines
6.1 KiB
C
/*
|
|
* Copyright (c) 2017, George Oikonomou - http://www.spd.gr
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
#ifndef CC13XX_CC26XX_DEF_H_
|
|
#define CC13XX_CC26XX_DEF_H_
|
|
/*---------------------------------------------------------------------------*/
|
|
#include "cm3/cm3-def.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
/* TSCH related defines */
|
|
|
|
/* 2 bytes header, 4 bytes CRC */
|
|
#define CC13XX_RADIO_PHY_OVERHEAD 6
|
|
/* 3 bytes preamble, 3 bytes sync */
|
|
#define CC13XX_RADIO_PHY_HEADER_LEN 6
|
|
/* The default data rate is 50 kbps */
|
|
#define CC13XX_RADIO_BIT_RATE 50000
|
|
|
|
/* 1 len byte, 2 bytes CRC */
|
|
#define CC26XX_RADIO_PHY_OVERHEAD 3
|
|
/* 4 bytes preamble, 1 byte sync */
|
|
#define CC26XX_RADIO_PHY_HEADER_LEN 5
|
|
/* The fixed data rate is 250 kbps */
|
|
#define CC26XX_RADIO_BIT_RATE 250000
|
|
|
|
#if CPU_FAMILY_CC13XX
|
|
#define RADIO_PHY_HEADER_LEN CC13XX_RADIO_PHY_HEADER_LEN
|
|
#define RADIO_PHY_OVERHEAD CC13XX_RADIO_PHY_OVERHEAD
|
|
#define RADIO_BIT_RATE CC13XX_RADIO_BIT_RATE
|
|
|
|
/* The TSCH default slot length of 10ms is too short, use custom one instead */
|
|
#ifndef TSCH_CONF_DEFAULT_TIMESLOT_TIMING
|
|
#define TSCH_CONF_DEFAULT_TIMESLOT_TIMING tsch_timing_cc13xx_50kbps
|
|
#endif /* TSCH_CONF_DEFAULT_TIMESLOT_TIMING */
|
|
|
|
/* Symbol for the custom TSCH timeslot timing template */
|
|
#define TSCH_CONF_ARCH_HDR_PATH "rf-core/cc13xx-50kbps-tsch.h"
|
|
|
|
#else
|
|
#define RADIO_PHY_HEADER_LEN CC26XX_RADIO_PHY_HEADER_LEN
|
|
#define RADIO_PHY_OVERHEAD CC26XX_RADIO_PHY_OVERHEAD
|
|
#define RADIO_BIT_RATE CC26XX_RADIO_BIT_RATE
|
|
#endif
|
|
|
|
#define RADIO_BYTE_AIR_TIME (1000000 / (RADIO_BIT_RATE / 8))
|
|
|
|
/* Delay between GO signal and SFD */
|
|
#define RADIO_DELAY_BEFORE_TX ((unsigned)US_TO_RTIMERTICKS(RADIO_PHY_HEADER_LEN * RADIO_BYTE_AIR_TIME))
|
|
/* Delay between GO signal and start listening.
|
|
* This value is so small because the radio is constantly on within each timeslot. */
|
|
#define RADIO_DELAY_BEFORE_RX ((unsigned)US_TO_RTIMERTICKS(15))
|
|
/* Delay between the SFD finishes arriving and it is detected in software. */
|
|
#define RADIO_DELAY_BEFORE_DETECT ((unsigned)US_TO_RTIMERTICKS(352))
|
|
|
|
/* Timer conversion; radio is running at 4 MHz */
|
|
#define RADIO_TIMER_SECOND 4000000u
|
|
#if (RTIMER_SECOND % 256) || (RADIO_TIMER_SECOND % 256)
|
|
#error RADIO_TO_RTIMER macro must be fixed!
|
|
#endif
|
|
#define RADIO_TO_RTIMER(X) ((uint32_t)(((uint64_t)(X) * (RTIMER_SECOND / 256)) / (RADIO_TIMER_SECOND / 256)))
|
|
#define USEC_TO_RADIO(X) ((X) * 4)
|
|
|
|
/* Do not turn off TSCH within a timeslot: not enough time */
|
|
#define TSCH_CONF_RADIO_ON_DURING_TIMESLOT 1
|
|
|
|
/* Disable TSCH frame filtering */
|
|
#define TSCH_CONF_HW_FRAME_FILTERING 0
|
|
|
|
/* Use hardware timestamps */
|
|
#ifndef TSCH_CONF_RESYNC_WITH_SFD_TIMESTAMPS
|
|
#define TSCH_CONF_RESYNC_WITH_SFD_TIMESTAMPS 1
|
|
#define TSCH_CONF_TIMESYNC_REMOVE_JITTER 0
|
|
#endif
|
|
|
|
#ifndef TSCH_CONF_BASE_DRIFT_PPM
|
|
/* The drift compared to "true" 10ms slots.
|
|
* Enable adaptive sync to enable compensation for this.
|
|
* Slot length 10000 usec
|
|
* 328 ticks
|
|
* Tick duration 30.517578125 usec
|
|
* Real slot duration 10009.765625 usec
|
|
* Target - real duration = -9.765625 usec
|
|
* TSCH_CONF_BASE_DRIFT_PPM -977
|
|
*/
|
|
#define TSCH_CONF_BASE_DRIFT_PPM -977
|
|
#endif
|
|
|
|
/* 10 times per second */
|
|
#ifndef TSCH_CONF_CHANNEL_SCAN_DURATION
|
|
#define TSCH_CONF_CHANNEL_SCAN_DURATION (CLOCK_SECOND / 10)
|
|
#endif
|
|
|
|
/* Increase this from the default 100 to improve TSCH association speed on this platform */
|
|
#ifndef TSCH_CONF_ASSOCIATION_POLL_FREQUENCY
|
|
#define TSCH_CONF_ASSOCIATION_POLL_FREQUENCY 1000
|
|
#endif
|
|
|
|
/* Slightly reduce the TSCH guard time (from 2200 usec to 1800 usec) to make sure
|
|
* the CC26xx radio has sufficient time to start up. */
|
|
#ifndef TSCH_CONF_RX_WAIT
|
|
#define TSCH_CONF_RX_WAIT 1800
|
|
#endif
|
|
/*---------------------------------------------------------------------------*/
|
|
#define RTIMER_ARCH_SECOND 65536
|
|
/*---------------------------------------------------------------------------*/
|
|
/* Path to CMSIS header */
|
|
#define CMSIS_CONF_HEADER_PATH "cc13x0-cc26x0-cm3.h"
|
|
|
|
/* Path to headers with implementation of mutexes and memory barriers */
|
|
#define MUTEX_CONF_ARCH_HEADER_PATH "mutex-cortex.h"
|
|
#define MEMORY_BARRIER_CONF_ARCH_HEADER_PATH "memory-barrier-cortex.h"
|
|
|
|
#define GPIO_HAL_CONF_ARCH_HDR_PATH "dev/gpio-hal-arch.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
#define GPIO_HAL_CONF_ARCH_SW_TOGGLE 0
|
|
/*---------------------------------------------------------------------------*/
|
|
#define SPI_CONF_CONTROLLER_COUNT 2
|
|
/*---------------------------------------------------------------------------*/
|
|
#endif /* CC13XX_CC26XX_DEF_H_ */
|
|
/*---------------------------------------------------------------------------*/
|