151 lines
4.1 KiB
C
151 lines
4.1 KiB
C
/*
|
|
* Copyright (c) 2006, Swedish Institute of Computer Science
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the Institute nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
* @(#)$Id: slip_uart1.c,v 1.7 2007/05/22 21:00:27 adamdunkels Exp $
|
|
*/
|
|
|
|
/*
|
|
* Machine dependent MSP430 SLIP routines for UART1.
|
|
*/
|
|
|
|
#include <io.h>
|
|
#include <signal.h>
|
|
|
|
#include "contiki.h"
|
|
|
|
#include "dev/slip.h"
|
|
|
|
void
|
|
slip_arch_writeb(unsigned char c)
|
|
{
|
|
/* Loop until the transmission buffer is available. */
|
|
while ((IFG2 & UTXIFG1) == 0);
|
|
|
|
/* Transmit the data. */
|
|
TXBUF1 = c;
|
|
}
|
|
|
|
/*
|
|
* The serial line is used to transfer IP packets using slip. To make
|
|
* it possible to send debug output over the same line we send debug
|
|
* output as slip frames (i.e delimeted by SLIP_END).
|
|
*
|
|
*/
|
|
int
|
|
putchar(int c)
|
|
{
|
|
#define SLIP_END 0300
|
|
static char debug_frame = 0;
|
|
|
|
if (!debug_frame) { /* Start of debug output */
|
|
slip_arch_writeb(SLIP_END);
|
|
slip_arch_writeb('\r'); /* Type debug line == '\r' */
|
|
debug_frame = 1;
|
|
}
|
|
|
|
slip_arch_writeb((char)c);
|
|
|
|
/*
|
|
* Line buffered output, a newline marks the end of debug output and
|
|
* implicitly flushes debug output.
|
|
*/
|
|
if (c == '\n') {
|
|
slip_arch_writeb(SLIP_END);
|
|
debug_frame = 0;
|
|
}
|
|
|
|
return c;
|
|
}
|
|
|
|
/**
|
|
* Initalize the RS232 port and the SLIP driver.
|
|
*
|
|
*/
|
|
void
|
|
slip_arch_init(unsigned long ubr)
|
|
{
|
|
/* RS232 */
|
|
P3DIR &= ~0x80; /* Select P37 for input (UART1RX) */
|
|
P3DIR |= 0x40; /* Select P36 for output (UART1TX) */
|
|
P3SEL |= 0xC0; /* Select P36,P37 for UART1{TX,RX} */
|
|
|
|
UCTL1 = SWRST | CHAR; /* 8-bit character, UART mode */
|
|
|
|
#if 0
|
|
U1RCTL &= ~URXEIE; /* even erroneous characters trigger interrupts */
|
|
#endif
|
|
|
|
UTCTL1 = SSEL1; /* UCLK = MCLK */
|
|
|
|
UBR01 = ubr;
|
|
UBR11 = ubr >> 8; /* always zero */
|
|
/*
|
|
* UMCTL1 values calculated using
|
|
* http://mspgcc.sourceforge.net/baudrate.html and are not
|
|
* complete. Also the table assumes that F_CPU = 2,457,600 Hz.
|
|
*/
|
|
switch (ubr) {
|
|
case BAUD2UBR(115200):
|
|
UMCTL1 = 0x4a;
|
|
break;
|
|
case BAUD2UBR(57600):
|
|
UMCTL1 = 0x5b;
|
|
break;
|
|
case BAUD2UBR(19600):
|
|
UMCTL1 = 0x4a;
|
|
break;
|
|
default:
|
|
UMCTL1 = 0x00;
|
|
}
|
|
|
|
ME2 &= ~USPIE1; /* USART1 SPI module disable */
|
|
ME2 |= (UTXE1 | URXE1); /* Enable USART1 TXD/RXD */
|
|
|
|
UCTL1 &= ~SWRST;
|
|
|
|
/* XXX Clear pending interrupts before enable!!! */
|
|
|
|
IE2 |= URXIE1; /* Enable USART1 RX interrupt */
|
|
}
|
|
|
|
interrupt(UART1RX_VECTOR)
|
|
__uart1_intr()
|
|
{
|
|
ENERGEST_ON(ENERGEST_TYPE_IRQ);
|
|
/* Check status register for receive errors. */
|
|
if(URCTL1 & RXERR) {
|
|
volatile unsigned dummy;
|
|
dummy = RXBUF1; /* Clear error flags by forcing a dummy read. */
|
|
} else {
|
|
if(slip_input_byte(RXBUF1)) {
|
|
LPM4_EXIT;
|
|
}
|
|
}
|
|
ENERGEST_OFF(ENERGEST_TYPE_IRQ);
|
|
}
|