nes-proj/drivers/platform/zoul/orion/enc28j60-arch-gpio.c

155 lines
5.0 KiB
C

/*
* Copyright (c) 2012-2013, Thingsquare, http://www.thingsquare.com/.
* Copyright (c) 2016, Zolertia <http://www.zolertia.com>
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the copyright holder nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
* OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/*---------------------------------------------------------------------------*/
/**
* \addtogroup zolertia-orion-ethernet-router
* @{
*
* \defgroup zolertia-eth-arch-gpio Zolertia ENC28J60 GPIO arch
*
* ENC28J60 eth-gw GPIO arch specifics
* @{
*
* \file
* eth-gw GPIO arch specifics
*/
/*---------------------------------------------------------------------------*/
#include "clock.h"
#include "dev/gpio.h"
/*---------------------------------------------------------------------------*/
#define CLK_PORT GPIO_PORT_TO_BASE(ETH_SPI_CLK_PORT)
#define CLK_BIT GPIO_PIN_MASK(ETH_SPI_CLK_PIN)
#define MOSI_PORT GPIO_PORT_TO_BASE(ETH_SPI_MOSI_PORT)
#define MOSI_BIT GPIO_PIN_MASK(ETH_SPI_MOSI_PIN)
#define MISO_PORT GPIO_PORT_TO_BASE(ETH_SPI_MISO_PORT)
#define MISO_BIT GPIO_PIN_MASK(ETH_SPI_MISO_PIN)
#define CSN_PORT GPIO_PORT_TO_BASE(ETH_SPI_CSN_PORT)
#define CSN_BIT GPIO_PIN_MASK(ETH_SPI_CSN_PIN)
#define RESET_PORT GPIO_PORT_TO_BASE(ETH_RESET_PORT)
#define RESET_BIT GPIO_PIN_MASK(ETH_RESET_PIN)
/*---------------------------------------------------------------------------*/
/* Delay in us */
#define DELAY 10
/*---------------------------------------------------------------------------*/
static void
delay(void)
{
clock_delay_usec(DELAY);
}
/*---------------------------------------------------------------------------*/
void
enc28j60_arch_spi_select(void)
{
GPIO_CLR_PIN(CSN_PORT, CSN_BIT);
delay();
}
/*---------------------------------------------------------------------------*/
void
enc28j60_arch_spi_deselect(void)
{
GPIO_SET_PIN(CSN_PORT, CSN_BIT);
}
/*---------------------------------------------------------------------------*/
void
enc28j60_arch_spi_init(void)
{
/* Set all pins to GPIO mode */
GPIO_SOFTWARE_CONTROL(CLK_PORT, CLK_BIT);
GPIO_SOFTWARE_CONTROL(MOSI_PORT, MOSI_BIT);
GPIO_SOFTWARE_CONTROL(MISO_PORT, MISO_BIT);
GPIO_SOFTWARE_CONTROL(CSN_PORT, CSN_BIT);
GPIO_SOFTWARE_CONTROL(RESET_PORT, RESET_BIT);
/* CSN, MOSI, CLK and RESET are output pins */
GPIO_SET_OUTPUT(CSN_PORT, CSN_BIT);
GPIO_SET_OUTPUT(MOSI_PORT, MOSI_BIT);
GPIO_SET_OUTPUT(CLK_PORT, CLK_BIT);
GPIO_SET_OUTPUT(RESET_PORT, RESET_BIT);
/* MISO is an input pin */
GPIO_SET_INPUT(MISO_PORT, MISO_BIT);
/* Enable the device */
GPIO_SET_INPUT(RESET_PORT, RESET_BIT);
/* The CS pin is active low, so we set it high when we haven't
selected the chip. */
enc28j60_arch_spi_deselect();
/* The CLK is active low, we set it high when we aren't using it. */
GPIO_CLR_PIN(CLK_PORT, CLK_BIT);
}
/*---------------------------------------------------------------------------*/
uint8_t
enc28j60_arch_spi_write(uint8_t output)
{
int i;
uint8_t input;
input = 0;
for(i=0; i < 8; i++) {
/* Write data on MOSI pin */
if(output & 0x80) {
GPIO_SET_PIN(MOSI_PORT, MOSI_BIT);
} else {
GPIO_CLR_PIN(MOSI_PORT, MOSI_BIT);
}
output <<= 1;
/* Set clock high */
GPIO_SET_PIN(CLK_PORT, CLK_BIT);
delay();
/* Read data from MISO pin */
input <<= 1;
if(GPIO_READ_PIN(MISO_PORT, MISO_BIT) != 0) {
input |= 0x1;
}
/* Set clock low */
GPIO_CLR_PIN(CLK_PORT, CLK_BIT);
delay();
}
return input;
}
/*---------------------------------------------------------------------------*/
uint8_t
enc28j60_arch_spi_read(void)
{
return enc28j60_arch_spi_write(0);
}
/*---------------------------------------------------------------------------*/
/**
* @}
* @}
*/