nes-proj/drivers/platform/zoul/remote-revb/power-mgmt.c

292 lines
8.7 KiB
C

/*
* Copyright (c) 2016, Zolertia - http://www.zolertia.com
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the Institute nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
*/
/*---------------------------------------------------------------------------*/
/**
* \addtogroup remote-power-mgmt-revb
* @{
* RE-Mote power management functions.
*
* @{
*
* \author
* Aitor Mejias <amejias@zolertia.com>
* Antonio Lignan <alinan@zolertia.com>
*/
/* -------------------------------------------------------------------------- */
#include <stdio.h>
#include <stdint.h>
#include "contiki.h"
#include "dev/gpio.h"
#include "sys/rtimer.h"
#include "power-mgmt.h"
#include "dev/i2c.h"
/* -------------------------------------------------------------------------- */
#define DEBUG 0
#if DEBUG
#define PRINTF(...) printf(__VA_ARGS__)
#else
#define PRINTF(...)
#endif
/* -------------------------------------------------------------------------- */
#define PM_ENABLE_LINE_SET GPIO_SET_PIN(PM_ENABLE_PORT_BASE, \
PM_ENABLE_PIN_MASK)
#define PM_ENABLE_LINE_CLR GPIO_CLR_PIN(PM_ENABLE_PORT_BASE, \
PM_ENABLE_PIN_MASK)
#define PM_ENABLE_AS_OUTPUT GPIO_SET_OUTPUT(PM_ENABLE_PORT_BASE, \
PM_ENABLE_PIN_MASK)
#define PM_ENABLE_LINE_CMD PM_ENABLE_LINE_SET; \
clock_delay_usec(100);
/* -------------------------------------------------------------------------- */
#define PM_NUMBITS(X) (1 << ((X)-1))
/* -------------------------------------------------------------------------- */
static uint8_t initialized = 0;
static uint8_t lbuf[5];
/* -------------------------------------------------------------------------- */
int8_t
pm_enable(void)
{
/* Set as output/low to set IDLE state */
GPIO_SOFTWARE_CONTROL(PM_ENABLE_PORT_BASE, PM_ENABLE_PIN_MASK);
PM_ENABLE_AS_OUTPUT;
i2c_init(I2C_SDA_PORT, I2C_SDA_PIN, I2C_SCL_PORT, I2C_SCL_PIN,
I2C_SCL_NORMAL_BUS_SPEED);
initialized = 1;
return PM_SUCCESS;
}
/* -------------------------------------------------------------------------- */
static int
pm_write_byte(uint8_t reg, uint8_t val)
{
if(!initialized) {
return PM_ERROR;
}
lbuf[0] = reg;
lbuf[1] = val;
PM_ENABLE_LINE_CMD;
if(i2c_burst_send(PWR_MNGMT_ADDR, lbuf, 2) == I2C_MASTER_ERR_NONE) {
PM_ENABLE_LINE_CLR;
return PM_SUCCESS;
}
PM_ENABLE_LINE_CLR;
return PM_ERROR;
}
/*---------------------------------------------------------------------------*/
static int
pm_read_byte(uint8_t reg, uint8_t *val, uint8_t len)
{
/* Detect valid register parameter */
if((reg < PM_VBAT) || (reg >= PM_MAX_COMMANDS) || (!len)) {
PRINTF("PM: invalid settings/not initialized\n");
return PM_ERROR;
}
PM_ENABLE_LINE_CMD;
if(i2c_single_send(PWR_MNGMT_ADDR, reg) == I2C_MASTER_ERR_NONE) {
if(i2c_burst_receive(PWR_MNGMT_ADDR, val, len) == I2C_MASTER_ERR_NONE) {
printf("PM: Data 0x%02X\n", *val);
PM_ENABLE_LINE_CLR;
return PM_SUCCESS;
}
}
PRINTF("PM: Error reading the registers\n");
PM_ENABLE_LINE_CLR;
return PM_ERROR;
}
/* -------------------------------------------------------------------------- */
int8_t
pm_reset_system(void)
{
if(!initialized) {
return PM_ERROR;
}
/* Reset the low-power PIC and the whole board as a bonus */
lbuf[0] = PM_CMD_RST_HARD;
lbuf[1] = 1;
PM_ENABLE_LINE_CMD;
if(i2c_burst_send(PWR_MNGMT_ADDR, lbuf, 2) == I2C_MASTER_ERR_NONE) {
clock_delay_usec(1000);
PM_ENABLE_LINE_CLR;
return PM_SUCCESS;
}
PM_ENABLE_LINE_CLR;
return PM_ERROR;
}
/* -------------------------------------------------------------------------- */
int8_t
pm_set_timeout(uint32_t time)
{
if(!initialized) {
return PM_ERROR;
}
if(time > PM_SOFT_SHTDN_28_DAYS) {
PRINTF("PM: maximum timeout is %u\n", (uint32_t)PM_SOFT_SHTDN_28_DAYS);
return PM_ERROR;
}
lbuf[0] = PM_SOFT_TIME;
lbuf[1] = (uint8_t)(time >> 24);
lbuf[2] = (uint8_t)(time >> 16) & 0xFF;
lbuf[3] = (uint8_t)(time >> 8) & 0xFF;
lbuf[4] = (uint8_t)(time & 0xFF);
PRINTF("PM: Timeout 0x%02x%02x%02x%02x\n", lbuf[1], lbuf[2], lbuf[3], lbuf[4]);
PM_ENABLE_LINE_CMD;
if(i2c_burst_send(PWR_MNGMT_ADDR, lbuf, 5) == I2C_MASTER_ERR_NONE) {
PM_ENABLE_LINE_CLR;
return PM_SUCCESS;
}
PRINTF("PM: error setting the timeout\n");
PM_ENABLE_LINE_CLR;
return PM_ERROR;
}
/* -------------------------------------------------------------------------- */
uint32_t
pm_get_timeout(void)
{
uint32_t retval = 0;
PM_ENABLE_LINE_CMD;
if(i2c_single_send(PWR_MNGMT_ADDR, PM_SOFT_TIME) == I2C_MASTER_ERR_NONE) {
if(i2c_burst_receive(PWR_MNGMT_ADDR, lbuf, 4) == I2C_MASTER_ERR_NONE) {
retval |= ((uint32_t)lbuf[0] << 24);
retval |= ((uint32_t)lbuf[1] << 16);
retval |= ((uint32_t)lbuf[2] << 8);
retval |= lbuf[3];
}
}
PM_ENABLE_LINE_CLR;
PRINTF("PM: Timeout 0x%02x%02x%02x%02x\n", lbuf[0], lbuf[1], lbuf[2], lbuf[3]);
retval *= PM_SOFT_SHTDN_INTERVAL;
retval /= 100;
return retval;
}
/* -------------------------------------------------------------------------- */
uint32_t
pm_get_num_cycles(void)
{
uint32_t retval = 0;
PM_ENABLE_LINE_CMD;
if(i2c_single_send(PWR_MNGMT_ADDR, PM_GET_NUM_CYCLES) == I2C_MASTER_ERR_NONE) {
if(i2c_burst_receive(PWR_MNGMT_ADDR, lbuf, 4) == I2C_MASTER_ERR_NONE) {
retval |= ((uint32_t)lbuf[0] << 24);
retval |= ((uint32_t)lbuf[1] << 16);
retval |= ((uint32_t)lbuf[2] << 8);
retval |= lbuf[3];
}
}
PM_ENABLE_LINE_CLR;
PRINTF("PM: Sleep cycles: 0x%02x%02x%02x%02x\n", lbuf[0], lbuf[1], lbuf[2],
lbuf[3]);
return retval;
}
/* -------------------------------------------------------------------------- */
int8_t
pm_shutdown_now(uint8_t type)
{
if(!initialized) {
PRINTF("PM: Not initialized\n");
return PM_ERROR;
}
if((type != PM_HARD_SLEEP_CONFIG) && (type != PM_SOFT_SLEEP_CONFIG)) {
PRINTF("PM: Invalid shutdown mode type\n");
return PM_ERROR;
}
PM_ENABLE_LINE_CMD;
if(type == PM_HARD_SLEEP_CONFIG) {
pm_write_byte(PM_HARD_SLEEP_CONFIG, PM_ENABLE);
PM_ENABLE_LINE_CLR;
return PM_SUCCESS;
}
/* Soft sleep */
pm_write_byte(PM_SOFT_SLEEP_CONFIG, PM_ENABLE);
PM_ENABLE_LINE_CLR;
return PM_SUCCESS;
}
/* -------------------------------------------------------------------------- */
int8_t
pm_get_voltage(uint16_t *state)
{
if(!initialized) {
return PM_ERROR;
}
PM_ENABLE_LINE_CMD;
if(i2c_single_send(PWR_MNGMT_ADDR, PM_GET_VDD) == I2C_MASTER_ERR_NONE) {
/* Read two bytes only */
if(i2c_burst_receive(PWR_MNGMT_ADDR, lbuf, 2) == I2C_MASTER_ERR_NONE) {
*state = (uint16_t)lbuf[0] << 8;
*state += lbuf[1];
/* Delay required for the command to finish */
clock_delay_usec(3000);
PRINTF("PM: Voltage %u [%u][%u]\n", *state, lbuf[0], lbuf[1]);
PM_ENABLE_LINE_CLR;
return PM_SUCCESS;
}
}
PM_ENABLE_LINE_CLR;
return PM_ERROR;
}
/* -------------------------------------------------------------------------- */
int8_t
pm_get_fw_ver(uint8_t *fwver)
{
if((!initialized) || (fwver == NULL)) {
return PM_ERROR;
}
if(pm_read_byte(PM_FW_VERSION, fwver, 1) == PM_SUCCESS) {
return PM_SUCCESS;
}
return PM_ERROR;
}
/*---------------------------------------------------------------------------*/
/**
* @}
* @}
*/