136 lines
6.2 KiB
C
136 lines
6.2 KiB
C
/*
|
|
* Copyright (c) 2018, Texas Instruments Incorporated - http://www.ti.com/
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
/*
|
|
* Parameter summary
|
|
* Adv. Address: 010203040506
|
|
* Adv. Data: 255
|
|
* BLE Channel: 17
|
|
* Frequency: 2440 MHz
|
|
* PDU Payload length:: 30
|
|
* TX Power: 5 dBm
|
|
* Whitening: true
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
#include "sys/cc.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
#include <ti/devices/DeviceFamily.h>
|
|
#include DeviceFamily_constructPath(driverlib/rf_mailbox.h)
|
|
#include DeviceFamily_constructPath(driverlib/rf_common_cmd.h)
|
|
#include DeviceFamily_constructPath(driverlib/rf_ble_cmd.h)
|
|
#include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_ble.h)
|
|
#include DeviceFamily_constructPath(rf_patches/rf_patch_rfe_ble.h)
|
|
|
|
#include <ti/drivers/rf/RF.h>
|
|
/*---------------------------------------------------------------------------*/
|
|
#include "ble-settings.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
/* TI-RTOS RF Mode Object */
|
|
RF_Mode rf_ble_mode =
|
|
{
|
|
.rfMode = RF_MODE_MULTIPLE,
|
|
.cpePatchFxn = &rf_patch_cpe_ble,
|
|
.mcePatchFxn = 0,
|
|
.rfePatchFxn = &rf_patch_rfe_ble,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
/* Overrides for CMD_RADIO_SETUP */
|
|
uint32_t rf_ble_overrides[] CC_ALIGN(4) =
|
|
{
|
|
/* override_use_patch_ble_1mbps.xml */
|
|
MCE_RFE_OVERRIDE(0,0,0,1,0,0), /* PHY: Use MCE ROM, RFE RAM patch */
|
|
/* override_synth_ble_1mbps.xml */
|
|
HW_REG_OVERRIDE(0x4038,0x0035), /* Synth: Set recommended RTRIM to 5 */
|
|
(uint32_t)0x000784A3, /* Synth: Set Fref to 3.43 MHz */
|
|
(uint32_t)0xA47E0583, /* Synth: Set loop bandwidth after lock to 80 kHz */
|
|
(uint32_t)0xEAE00603, /* Synth: Set loop bandwidth after lock to 80 kHz */
|
|
(uint32_t)0x00010623, /* Synth: Set loop bandwidth after lock to 80 kHz */
|
|
HW32_ARRAY_OVERRIDE(0x405C,1), /* Synth: Configure PLL bias */
|
|
(uint32_t)0x1801F800, /* Synth: Configure PLL bias */
|
|
HW32_ARRAY_OVERRIDE(0x402C,1), /* Synth: Configure PLL latency */
|
|
(uint32_t)0x00608402, /* Synth: Configure PLL latency */
|
|
(uint32_t)0x02010403, /* Synth: Use 24 MHz XOSC as synth clock, enable extra PLL filtering */
|
|
HW32_ARRAY_OVERRIDE(0x4034,1), /* Synth: Configure extra PLL filtering */
|
|
(uint32_t)0x177F0408, /* Synth: Configure extra PLL filtering */
|
|
(uint32_t)0x38000463, /* Synth: Configure extra PLL filtering */
|
|
/* override_phy_ble_1mbps.xml */
|
|
(uint32_t)0x013800C3, /* Tx: Configure symbol shape for BLE frequency deviation requirements */
|
|
HW_REG_OVERRIDE(0x6088, 0x0045), /* Rx: Configure AGC reference level */
|
|
/* Tx: Configure pilot tone length to ensure stable frequency */
|
|
HW_REG_OVERRIDE(0x52AC, 0x0360), /* before start of packet */
|
|
(uint32_t)0x01AD02A3, /* Tx: Compensate timing offset to match new pilot tone setting */
|
|
(uint32_t)0x01680263, /* Tx: Compensate timing offset to match new pilot tone setting */
|
|
(uint32_t)0xFFFFFFFF,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
/* CMD_RADIO_SETUP: Radio Setup Command for Pre-Defined Schemes */
|
|
rfc_CMD_RADIO_SETUP_t rf_ble_cmd_radio_setup =
|
|
{
|
|
.commandNo = CMD_RADIO_SETUP,
|
|
.status = IDLE,
|
|
.pNextOp = 0,
|
|
.startTime = 0x00000000,
|
|
.startTrigger.triggerType = TRIG_NOW,
|
|
.startTrigger.bEnaCmd = 0x0,
|
|
.startTrigger.triggerNo = 0x0,
|
|
.startTrigger.pastTrig = 0x0,
|
|
.condition.rule = COND_NEVER,
|
|
.condition.nSkip = 0x0,
|
|
.mode = 0x00,
|
|
.__dummy0 = 0x00,
|
|
.config.frontEndMode = 0x0,
|
|
.config.biasMode = 0x0,
|
|
.config.analogCfgMode = 0x0,
|
|
.config.bNoFsPowerUp = 0x0,
|
|
.txPower = 0x9330,
|
|
.pRegOverride = rf_ble_overrides,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
/* CMD_BLE_ADV_NC: BLE Non-Connectable Advertiser Command */
|
|
rfc_CMD_BLE_ADV_NC_t rf_ble_cmd_ble_adv_nc =
|
|
{
|
|
.commandNo = CMD_BLE_ADV_NC,
|
|
.status = IDLE,
|
|
.pNextOp = 0,
|
|
.startTime = 0x00000000,
|
|
.startTrigger.triggerType = TRIG_NOW,
|
|
.startTrigger.bEnaCmd = 0x0,
|
|
.startTrigger.triggerNo = 0x0,
|
|
.startTrigger.pastTrig = 0x1,
|
|
.condition.rule = 0x0, /* set by driver */
|
|
.condition.nSkip = 0x0,
|
|
.channel = 0x00, /* set by driver */
|
|
.whitening.init = 0x00, /* set by driver */
|
|
.whitening.bOverride = 0x1,
|
|
.pParams = 0x00000000, /* set by driver */
|
|
.pOutput = 0x00000000, /* set by driver */
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|