109 lines
3.9 KiB
C
109 lines
3.9 KiB
C
/*
|
|
* Copyright (c) 2016, Zolertia - http://www.zolertia.com
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
/**
|
|
* \addtogroup zoul-examples
|
|
* @{
|
|
*
|
|
* \defgroup zoul-servo-test Test the EMAX ES08A II servo motor
|
|
*
|
|
* Demonstrates the use of the EMAX ES08A servo motor. This servo requires a
|
|
* +5V voltage, it can be powered from D+5.1 pin (of the ADC3 connector), but
|
|
* it requires either an external power supply other than the USB for programing
|
|
* or it can be powered by the USB 2.0 connector, which allows a higher current
|
|
* draw.
|
|
*
|
|
* This test uses the default servo values (freq 50Hz, traveling time 1.5-1.9ms)
|
|
* for 0-180º movement, tested with the EMAX ES08A. Depending on the servo used
|
|
* you might need to adjust these parameters in the servo.h header file.
|
|
*
|
|
* @{
|
|
*
|
|
* \file
|
|
* A quick program for testing a servo motor
|
|
* \author
|
|
* Antonio Lignan <alinan@zolertia.com>
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
#include "contiki.h"
|
|
#include "dev/leds.h"
|
|
#include "dev/servo.h"
|
|
#include <stdio.h>
|
|
#include <stdint.h>
|
|
/*---------------------------------------------------------------------------*/
|
|
#define DEBUG 1
|
|
#if DEBUG
|
|
#define PRINTF(...) printf(__VA_ARGS__)
|
|
#else
|
|
#define PRINTF(...)
|
|
#endif
|
|
/*---------------------------------------------------------------------------*/
|
|
static struct etimer et;
|
|
/*---------------------------------------------------------------------------*/
|
|
PROCESS(servo_test_process, "Zolertia servo test process");
|
|
AUTOSTART_PROCESSES(&servo_test_process);
|
|
/*---------------------------------------------------------------------------*/
|
|
PROCESS_THREAD(servo_test_process, ev, data)
|
|
{
|
|
PROCESS_BEGIN();
|
|
|
|
static uint8_t deg = 0;
|
|
|
|
PRINTF("\nStarting the test\n");
|
|
|
|
while(1) {
|
|
|
|
servo_position(SERVO_CHANNEL_5, GPIO_A_NUM, 5, deg);
|
|
PRINTF("Current position --> %03uº\n", deg);
|
|
|
|
etimer_set(&et, CLOCK_SECOND / 2);
|
|
PROCESS_WAIT_EVENT_UNTIL(etimer_expired(&et));
|
|
|
|
/* Increase the position by 10º each iteration */
|
|
deg += 10;
|
|
if(deg > SERVO_MAX_DEGREES) {
|
|
deg = 0;
|
|
servo_stop(SERVO_CHANNEL_5, GPIO_A_NUM, 5);
|
|
|
|
/* Stop the servo and wait 2 seconds before resuming from start */
|
|
etimer_set(&et, CLOCK_SECOND * 2);
|
|
PROCESS_WAIT_EVENT_UNTIL(etimer_expired(&et));
|
|
}
|
|
}
|
|
|
|
PROCESS_END();
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* @}
|
|
* @}
|
|
*/
|
|
|