248 lines
10 KiB
C
248 lines
10 KiB
C
/*
|
|
* Copyright (c) 2018, Texas Instruments Incorporated - http://www.ti.com/
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
// Parameter summary
|
|
// IEEE Channel: 11
|
|
// Frequency: 2405 MHz
|
|
// SFD: 0
|
|
// Packet Data: 255
|
|
// Preamble (32 bit): 01010101...
|
|
// TX Power: 5 dBm
|
|
/*---------------------------------------------------------------------------*/
|
|
#include "sys/cc.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
#include <ti/devices/DeviceFamily.h>
|
|
#include DeviceFamily_constructPath(driverlib/rf_mailbox.h)
|
|
#include DeviceFamily_constructPath(driverlib/rf_common_cmd.h)
|
|
#include DeviceFamily_constructPath(driverlib/rf_ieee_cmd.h)
|
|
#include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_ieee.h)
|
|
|
|
#include <ti/drivers/rf/RF.h>
|
|
/*---------------------------------------------------------------------------*/
|
|
#include "ieee-settings.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
// TI-RTOS RF Mode Object
|
|
RF_Mode rf_ieee_mode =
|
|
{
|
|
.rfMode = RF_MODE_IEEE_15_4,
|
|
.cpePatchFxn = &rf_patch_cpe_ieee,
|
|
.mcePatchFxn = 0,
|
|
.rfePatchFxn = 0,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
// TX Power table
|
|
// The RF_TxPowerTable_DEFAULT_PA_ENTRY macro is defined in RF.h and requires the following arguments:
|
|
// RF_TxPowerTable_DEFAULT_PA_ENTRY(bias, gain, boost coefficient)
|
|
// See the Technical Reference Manual for further details about the "txPower" Command field.
|
|
// The PA settings require the CCFG_FORCE_VDDR_HH = 0 unless stated otherwise.
|
|
RF_TxPowerTable_Entry rf_ieee_tx_power_table[RF_IEEE_TX_POWER_TABLE_SIZE+1] =
|
|
{
|
|
{ -21, RF_TxPowerTable_DEFAULT_PA_ENTRY( 7, 3, 0, 6) },
|
|
{ -18, RF_TxPowerTable_DEFAULT_PA_ENTRY( 9, 3, 0, 6) },
|
|
{ -15, RF_TxPowerTable_DEFAULT_PA_ENTRY(11, 3, 0, 6) },
|
|
{ -12, RF_TxPowerTable_DEFAULT_PA_ENTRY(11, 1, 0, 10) },
|
|
{ -9, RF_TxPowerTable_DEFAULT_PA_ENTRY(14, 1, 1, 12) },
|
|
{ -6, RF_TxPowerTable_DEFAULT_PA_ENTRY(18, 1, 1, 14) },
|
|
{ -3, RF_TxPowerTable_DEFAULT_PA_ENTRY(24, 1, 1, 18) },
|
|
{ 0, RF_TxPowerTable_DEFAULT_PA_ENTRY(33, 1, 1, 24) },
|
|
{ 1, RF_TxPowerTable_DEFAULT_PA_ENTRY(20, 0, 0, 33) },
|
|
{ 2, RF_TxPowerTable_DEFAULT_PA_ENTRY(24, 0, 0, 39) },
|
|
{ 3, RF_TxPowerTable_DEFAULT_PA_ENTRY(28, 0, 0, 45) },
|
|
{ 4, RF_TxPowerTable_DEFAULT_PA_ENTRY(36, 0, 1, 73) },
|
|
{ 5, RF_TxPowerTable_DEFAULT_PA_ENTRY(48, 0, 1, 73) },
|
|
RF_TxPowerTable_TERMINATION_ENTRY
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
// Overrides for CMD_RADIO_SETUP
|
|
uint32_t rf_ieee_overrides[] CC_ALIGN(4) =
|
|
{
|
|
// override_synth_ieee_15_4.xml
|
|
HW_REG_OVERRIDE(0x4038,0x0035), // Synth: Set recommended RTRIM to 5
|
|
(uint32_t)0x000784A3, // Synth: Set Fref to 3.43 MHz
|
|
(uint32_t)0xA47E0583, // Synth: Set loop bandwidth after lock to 80 kHz
|
|
(uint32_t)0xEAE00603, // Synth: Set loop bandwidth after lock to 80 kHz
|
|
(uint32_t)0x00010623, // Synth: Set loop bandwidth after lock to 80 kHz
|
|
HW32_ARRAY_OVERRIDE(0x405C,1), // Synth: Configure PLL bias
|
|
(uint32_t)0x1801F800, // Synth: Configure PLL bias
|
|
HW32_ARRAY_OVERRIDE(0x402C,1), // Synth: Configure PLL latency
|
|
(uint32_t)0x00608402, // Synth: Configure PLL latency
|
|
(uint32_t)0x02010403, // Synth: Use 24 MHz XOSC as synth clock, enable extra PLL filtering
|
|
HW32_ARRAY_OVERRIDE(0x4034,1), // Synth: Configure extra PLL filtering
|
|
(uint32_t)0x177F0408, // Synth: Configure extra PLL filtering
|
|
(uint32_t)0x38000463, // Synth: Configure extra PLL filtering
|
|
// override_phy_ieee_15_4.xml
|
|
(uint32_t)0x05000243, // Synth: Increase synth programming timeout
|
|
(uint32_t)0x002082C3, // Rx: Adjust Rx FIFO threshold to avoid overflow
|
|
// override_frontend_id.xml
|
|
(uint32_t)0x000288A3, // Rx: Set RSSI offset to adjust reported RSSI by -2 dB
|
|
(uint32_t)0x000F8883, // Rx: Configure LNA bias current trim offset
|
|
HW_REG_OVERRIDE(0x50DC,0x002B), // Rx: Adjust AGC DC filter
|
|
(uint32_t)0xFFFFFFFF,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
// CMD_RADIO_SETUP
|
|
// Radio Setup Command for Pre-Defined Schemes
|
|
rfc_CMD_RADIO_SETUP_t rf_cmd_ieee_radio_setup =
|
|
{
|
|
.commandNo = CMD_RADIO_SETUP,
|
|
.status = IDLE,
|
|
.pNextOp = 0,
|
|
.startTime = 0x00000000,
|
|
.startTrigger.triggerType = TRIG_NOW,
|
|
.startTrigger.bEnaCmd = 0x0,
|
|
.startTrigger.triggerNo = 0x0,
|
|
.startTrigger.pastTrig = 0x0,
|
|
.condition.rule = COND_NEVER,
|
|
.condition.nSkip = 0x0,
|
|
.mode = 0x01,
|
|
.__dummy0 = 0x00,
|
|
.config.frontEndMode = 0x0,
|
|
.config.biasMode = 0x1,
|
|
.config.analogCfgMode = 0x0,
|
|
.config.bNoFsPowerUp = 0x0,
|
|
.txPower = 0x9330, /* 5 dBm default */
|
|
.pRegOverride = rf_ieee_overrides,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
// CMD_FS
|
|
// Frequency Synthesizer Programming Command
|
|
rfc_CMD_FS_t rf_cmd_ieee_fs =
|
|
{
|
|
.commandNo = CMD_FS,
|
|
.status = IDLE,
|
|
.pNextOp = 0,
|
|
.startTime = 0x00000000,
|
|
.startTrigger.triggerType = TRIG_NOW,
|
|
.startTrigger.bEnaCmd = 0x0,
|
|
.startTrigger.triggerNo = 0x0,
|
|
.startTrigger.pastTrig = 0x0,
|
|
.condition.rule = COND_NEVER,
|
|
.condition.nSkip = 0x0,
|
|
.frequency = 0x0965, /* set by driver */
|
|
.fractFreq = 0x0000, /* set by driver */
|
|
.synthConf.bTxMode = 0x1,
|
|
.synthConf.refFreq = 0x0,
|
|
.__dummy0 = 0x00,
|
|
.__dummy1 = 0x00,
|
|
.__dummy2 = 0x00,
|
|
.__dummy3 = 0x0000,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
// CMD_IEEE_TX
|
|
// The command ID number 0x2C01
|
|
rfc_CMD_IEEE_TX_t rf_cmd_ieee_tx =
|
|
{
|
|
.commandNo = CMD_IEEE_TX,
|
|
.status = IDLE,
|
|
.pNextOp = 0,
|
|
.startTime = 0x00000000,
|
|
.startTrigger.triggerType = TRIG_NOW,
|
|
.startTrigger.bEnaCmd = 0x0,
|
|
.startTrigger.triggerNo = 0x0,
|
|
.startTrigger.pastTrig = 0x0,
|
|
.condition.rule = COND_NEVER,
|
|
.condition.nSkip = 0x0,
|
|
.txOpt.bIncludePhyHdr = 0x0,
|
|
.txOpt.bIncludeCrc = 0x0,
|
|
.txOpt.payloadLenMsb = 0x0,
|
|
.payloadLen = 0x0, /* set by driver */
|
|
.pPayload = 0, /* set by driver */
|
|
.timeStamp = 0x00000000,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
// CMD_IEEE_RX
|
|
// The command ID number 0x2801
|
|
rfc_CMD_IEEE_RX_t rf_cmd_ieee_rx =
|
|
{
|
|
.commandNo = CMD_IEEE_RX,
|
|
.status = IDLE,
|
|
.pNextOp = 0,
|
|
.startTime = 0x00000000,
|
|
.startTrigger.triggerType = TRIG_NOW,
|
|
.startTrigger.bEnaCmd = 0x0,
|
|
.startTrigger.triggerNo = 0x0,
|
|
.startTrigger.pastTrig = 0x0,
|
|
.condition.rule = COND_NEVER,
|
|
.condition.nSkip = 0x0,
|
|
.channel = 0x00, /* set by driver */
|
|
.rxConfig.bAutoFlushCrc = 0x1,
|
|
.rxConfig.bAutoFlushIgn = 0x0,
|
|
.rxConfig.bIncludePhyHdr = 0x0,
|
|
.rxConfig.bIncludeCrc = 0x1,
|
|
.rxConfig.bAppendRssi = 0x1,
|
|
.rxConfig.bAppendCorrCrc = 0x1,
|
|
.rxConfig.bAppendSrcInd = 0x0,
|
|
.rxConfig.bAppendTimestamp = 0x1,
|
|
.pRxQ = 0, /* set by driver */
|
|
.pOutput = 0, /* set by driver */
|
|
.frameFiltOpt.frameFiltEn = 0x0, /* set by driver */
|
|
.frameFiltOpt.frameFiltStop = 0x1,
|
|
.frameFiltOpt.autoAckEn = 0x0, /* set by driver */
|
|
.frameFiltOpt.slottedAckEn = 0x0,
|
|
.frameFiltOpt.autoPendEn = 0x0,
|
|
.frameFiltOpt.defaultPend = 0x0,
|
|
.frameFiltOpt.bPendDataReqOnly = 0x0,
|
|
.frameFiltOpt.bPanCoord = 0x0,
|
|
.frameFiltOpt.maxFrameVersion = 0x2,
|
|
.frameFiltOpt.fcfReservedMask = 0x0,
|
|
.frameFiltOpt.modifyFtFilter = 0x0,
|
|
.frameFiltOpt.bStrictLenFilter = 0x0,
|
|
.frameTypes.bAcceptFt0Beacon = 0x1,
|
|
.frameTypes.bAcceptFt1Data = 0x1,
|
|
.frameTypes.bAcceptFt2Ack = 0x1,
|
|
.frameTypes.bAcceptFt3MacCmd = 0x1,
|
|
.frameTypes.bAcceptFt4Reserved = 0x1,
|
|
.frameTypes.bAcceptFt5Reserved = 0x1,
|
|
.frameTypes.bAcceptFt6Reserved = 0x1,
|
|
.frameTypes.bAcceptFt7Reserved = 0x1,
|
|
.ccaOpt.ccaEnEnergy = 0x1,
|
|
.ccaOpt.ccaEnCorr = 0x1,
|
|
.ccaOpt.ccaEnSync = 0x1,
|
|
.ccaOpt.ccaCorrOp = 0x1,
|
|
.ccaOpt.ccaSyncOp = 0x0,
|
|
.ccaOpt.ccaCorrThr = 0x3,
|
|
.ccaRssiThr = 0x0, /* set by driver */
|
|
.__dummy0 = 0x00,
|
|
.numExtEntries = 0x00,
|
|
.numShortEntries = 0x00,
|
|
.pExtEntryList = 0,
|
|
.pShortEntryList = 0,
|
|
.localExtAddr = 0x0, /* set by driver */
|
|
.localShortAddr = 0x0, /* set by driver */
|
|
.localPanID = 0x0000,
|
|
.__dummy1 = 0x000000,
|
|
.endTrigger.triggerType = TRIG_NEVER,
|
|
.endTrigger.bEnaCmd = 0x0,
|
|
.endTrigger.triggerNo = 0x0,
|
|
.endTrigger.pastTrig = 0x0,
|
|
.endTime = 0x00000000,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|