Oliver Schmidt
9cdc6da040
Avoid access to the address register during auto-increment.
...
It cannot be ruled out that access to the address register triggers
an address auto-increment. Therefore a temporary address register
shadow is introduced to replace the access to the address regsiter.
Additionally there are several minor beautifications.
2013-12-03 21:31:43 +01:00
Ian Martin
0dafba4f6d
Add a rule for generating assembly listings on mc1322x targets, for example: "make webserver6.lst".
2013-12-01 16:22:37 -05:00
Mariano Alvira
5fbefbd87b
Merge pull request #459 from adamdunkels/push/mc1322x-stuff
...
MC1322x additions
2013-11-29 11:59:04 -08:00
Benoît Thébaudeau
1a696eb123
cc2538: gpio: Clear the power-up interrupts in the port ISRs
...
The pending GPIO power-up interrupts have to be cleared in the ISRs in order not
to re-trigger the interrupts and the wake-up events.
The power-up interrupts of all pins are cleared for each port in the
corresponding port ISR. This is done after calling the registered callbacks so
that the callbacks can know which pin woke up the SoC. This is done after
clearing the regular interrupt in order to avoid getting a new wake-up interrupt
without the regular interrupt in the case of a new wake-up edge occurring
between the two clears.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-26 22:20:05 +01:00
Benoît Thébaudeau
44a5c76884
cc2538: gpio: Add macros to use GPIO power-up interrupts
...
The GPIO power-up interrupts have to be configured and enabled in order to be
able to wake-up the SoC from PM1+ upon a signal edge occurring on a GPIO input
pin.
This set of macros allows to:
- configure the signal edge triggering a power-up interrupt,
- enable and disable a power-up interrupt,
- clear a power-up interrupt flag.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-26 22:10:47 +01:00
Benoît Thébaudeau
621f4f7339
cc2538: lpm: Give access to the SRAM non-retention area for PM2
...
If PM2 is enabled with LPM_CONF_MAX_PM, but not active, the non-retention area
of the SRAM can be useful to place temporary data that does not fit in the
low-leakage SRAM, typically after having called lpm_set_max_pm(LPM_PM1). Hence,
give access to this non-retention area thanks to .nrdata* sections.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-25 15:43:37 +01:00
Benoît Thébaudeau
270ed237fd
cc2538: usb: Make the GPIO driving the pull-up optional
...
The data sheet recommends that the USB pull-up resistor be driven by a GPIO so
that it can be controlled by software, but this is not mandatory. Hence, leave
the choice so that CC253-based boards not using this option can build and work
fine.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-25 15:15:35 +01:00
Benoît Thébaudeau
d2f3795a30
cc2538: Clean up port and pin definitions
...
Homogenize port and pin definitions naming:
- PERIPHERAL_FUNCTION_PORT for the port ID,
- PERIPHERAL_FUNCTION_PIN for the pin ID,
- PERIPHERAL_FUNCTION_PORT_BASE for the port base,
- PERIPHERAL_FUNCTION_PIN_MASK for the pin mask.
Define only PERIPHERAL_FUNCTION_PORT and PERIPHERAL_FUNCTION_PIN in board.h, and
deduce PERIPHERAL_FUNCTION_PORT_BASE and PERIPHERAL_FUNCTION_PIN_MASK in the
driver from the former definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-25 15:00:41 +01:00
Adam Dunkels
bb2dcaa057
A massive all-tree automated update of all double inclusion guard #defines that changes from using two underscores as a prefix, which are reserved, to not using two underscores as a prefix
2013-11-24 20:20:11 +01:00
Adam Dunkels
e09ff3ff1e
Merge pull request #438 from adamdunkels/push/cleanup-platforms
...
Massive platform cleanup
2013-11-24 01:59:53 -08:00
Adam Dunkels
1ab28e4668
Added missing argument declaration
2013-11-23 15:05:16 +01:00
Adam Dunkels
e95236b642
Added header declarations for cc2538_rf_read_rssi() and cc2538_rf_set_promiscous_mode()
2013-11-23 15:05:16 +01:00
Adam Dunkels
76f2a10c9a
Added a function for setting promiscous mode on the CC2538 RF core
2013-11-23 15:05:15 +01:00
Adam Dunkels
473d519926
Added a way to obtain the RSSI from the CC2538 RF core
2013-11-23 15:05:15 +01:00
Adam Dunkels
27433244a9
The pc-6001 platform was the last z80 platform in the tree, so we'll remove the cpu/z80 directory too
2013-11-22 16:33:46 +01:00
Adam Dunkels
7a310935d8
An implementation of the mc1322x watchdog
2013-11-22 15:54:06 +01:00
Adam Dunkels
88f9d79053
Enable the silent compilation mode from the latest Contiki
2013-11-22 15:53:30 +01:00
Oliver Schmidt
737d5fd6dc
Replaced web configurator with target-based ethconfig.
2013-11-21 21:57:42 +01:00
Oliver Schmidt
3abd5d3d8d
Show current IP config on startup.
2013-11-20 22:33:11 +01:00
George Oikonomou
f13af20f12
Merge pull request #409 from ADVANSEE/cc2538-spi
...
cc2538: spi: Bug fix and various improvements
2013-11-20 06:51:26 -08:00
Benoît Thébaudeau
e8a8870d1d
cc2538: spi: Add enable and disable functions
...
This makes it possible to reduce the power consumption when the SPI is unused.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-20 14:20:50 +01:00
Benoît Thébaudeau
b134e35450
cc2538: spi: Add format configuration options
...
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-20 14:20:43 +01:00
Nicolas Tsiftes
263e212427
Merge pull request #431 from adamdunkels/push/ipv6-const
...
Make IP addresses const
2013-11-20 04:26:05 -08:00
Nicolas Tsiftes
d183b87f4b
Merge pull request #434 from adamdunkels/push/cleanup-sys
...
Remove old unused code from the core/sys/ directory
2013-11-19 09:53:57 -08:00
George Oikonomou
dc05eea3f5
Merge pull request #426 from ADVANSEE/cc2538-rom
...
cc2538: Add driver for the rom utility function library
2013-11-19 03:09:16 -08:00
Adam Dunkels
30c0c5eaf6
Removed old unused timetable code
2013-11-19 08:29:23 +01:00
Adam Dunkels
469884171a
Added the const keyword to functions that use the tcpip_set_outputfunc(), which now takes a const argument
2013-11-18 23:26:37 +01:00
Benoît Thébaudeau
1f1b940cb9
cc2538: Add driver for the rom utility function library
...
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-18 12:38:06 +01:00
Benoît Thébaudeau
035a30602b
cc2538: lpm: Make periph_permit_pm1_funcs static
...
periph_permit_pm1_funcs[] is a private member of lpm.c, so define it as static.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-18 11:57:59 +01:00
George Oikonomou
b10c78f854
Merge pull request #425 from ADVANSEE/cc2538-gpio
...
cc2538: gpio: Bug fix and various improvements
2013-11-15 13:04:09 -08:00
George Oikonomou
98a1f2dfa9
Merge pull request #408 from ADVANSEE/cc2538-uart
...
cc2538: lpm: Add registration mechanism for peripherals and use it
2013-11-15 12:57:03 -08:00
Benoît Thébaudeau
680050861c
cc2538: gpio: Use accessor macros
...
Use the GPIO accessor macros instead of copying raw register access code all
over the place. This is cleaner and less error prone.
This fixes the setting of the USB pull-up resistor that worked only by chance on
the CC2538DK because it is controlled by the pin 0 of the used GPIO port.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 19:57:44 +01:00
Benoît Thébaudeau
923f161b7b
cc2538: gpio: Add pin read / write and interrupt clear macros
...
Introduce new useful GPIO macros to:
- read the levels of some port pins,
- write the levels of some port pins (pass bit-field value to be set),
- clear the interrupt flags for some port pins.
These macros are cleaner and less error prone than raw register access code
copied all over the place.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 19:48:24 +01:00
Benoît Thébaudeau
300d2d79ae
cc2538: gpio: Fix usage of parameters in macros
...
The parameters in the GPIO macros were used without being parenthesized. This
could generate wrong values for register assignments in the case of expressions
passed as arguments to these macros.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 19:43:06 +01:00
Benoît Thébaudeau
b8b54a033c
cc2538: uart: Fix crippled output occurring upon lpm_enter()
...
lpm_enter() must not enter PM1+ if the UART TX FIFO is not empty. Otherwise, the
UART clock gets disabled, and its TX is broken.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 17:24:26 +01:00
Benoît Thébaudeau
0692ee251d
cc2538: usb: Use the new LPM peripheral registration
...
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 17:14:45 +01:00
Benoît Thébaudeau
d35732505b
cc2538: lpm: Add registration mechanism for peripherals
...
Some peripherals have their clocks automatically gated in PM1+ modes, so they
cannot operate. This new mechanism gives peripherals a way to prohibit PM1+
modes so that they can properly complete their current operations before
entering PM1+.
This mechanism is implemented with peripheral functions registered to the LPM
module. These functions return whether the associated peripheral permits or not
PM1+ modes. They are called by the LPM module each time PM1+ might be possible.
If any of the peripherals wants to block PM1+, then the system is only dropped
to PM0.
Partly from: George Oikonomou
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 17:09:22 +01:00
George Oikonomou
d08a87880c
Merge pull request #410 from ADVANSEE/cc2538-sys_ctrl
...
cc2538: sys_ctrl: Make it possible to use the 32-kHz crystal
2013-11-15 07:42:45 -08:00
Benoît Thébaudeau
f1ca1b742c
cc2538: spi: Include spi-arch.h before dev/spi.h
...
spi-arch.h configures dev/spi.h, so it must be #included first. Luckily, this
mistake did not have any consequence here, but fix it in order to avoid possible
future issues.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 15:56:40 +01:00
Benoît Thébaudeau
f34731c1a9
cc2538: spi: Do not call SPI_WAITFOREORx() at end of init
...
If the SSI has never been used and spi_init() is called, then the SSI receive
FIFO is empty and remains so, so calling SPI_WAITFOREORx() at the end of
spi_init() waits endlessly for SSI_SR.RNE to be set. Hence, this call must be
removed in order to avoid a deadlock.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 15:56:40 +01:00
Benoît Thébaudeau
47d570343e
cc2538: sys_ctrl: Make it possible to use the 32-kHz crystal
...
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 15:52:10 +01:00
Benoît Thébaudeau
a7d10ce2ad
cc2538: Make it possible to use a custom linker script
...
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 15:41:58 +01:00
Benoît Thébaudeau
974850cdf2
cc2538: Generate .hex output
...
ELF files generated by GCC make SmartRF Flash Programmer 2 crash (only the TI
format is supported by this tool for ELFs), and binary files are not very
appropriate because they are gapless, so generate Intel HEX files since these
are very well supported by most programming tools while still flexible.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 15:41:58 +01:00
Mariano Alvira
6b9b457a60
Merge pull request #385 from ismb-pert/better-error-message
...
Better error message in case of wrong CPUREV value
2013-11-14 07:14:33 -08:00
Oliver Schmidt
59c28bc32b
Merge pull request #419 from oliverschmidt/master
...
Saved six more bytes ;-)
2013-11-13 14:43:06 -08:00
Oliver Schmidt
1bf5b4380d
Saved six more bytes ;-)
2013-11-13 23:32:49 +01:00
Oliver Schmidt
497e7fbbac
Merge pull request #416 from oliverschmidt/master
...
Added missing fixup & removed wait loop from poll.
2013-11-11 12:06:38 -08:00
Oliver Schmidt
ae1a875881
Added missing fixup & removed wait loop from poll.
2013-11-11 21:03:39 +01:00
Oliver Schmidt
dd30454c80
Merge pull request #415 from oliverschmidt/master
...
Added 6502 driver for WIZnet W5100 in MACRAW mode.
2013-11-09 14:17:07 -08:00
Oliver Schmidt
2d7d1b123d
Added 6502 driver for WIZnet W5100 in MACRAW mode.
2013-11-09 23:15:20 +01:00
George Oikonomou
ce0b2cacac
Merge pull request #365 from g-oikonomou/cc2538-uart-init-fix
...
Set peripheral mode for the correct CC2538 UART TX/RX pins
2013-10-23 07:10:41 -07:00
Gianfranco Costamagna
ddd6b900cd
Better error message in case of wrong CPUREV value
2013-10-17 12:33:36 +02:00
Oliver Schmidt
57d9c43a33
Removed support for 'atari' now that 'atarixl' is part of the cc65 master.
2013-10-03 22:55:32 +02:00
Oliver Schmidt
7c2f3b3911
Saved another byte ;-)
2013-10-03 22:32:12 +02:00
George Oikonomou
e4a454b284
Set peripheral mode for the correct UART TX/RX pins
2013-09-30 14:50:39 +01:00
George Oikonomou
2957d44ff8
Merge pull request #352 from lab11/cc2538-spi-driver
...
Added SPI driver for CC2538
2013-09-28 13:25:17 -07:00
Brad Campbell
e2af903d05
Added SPI driver for CC2538
...
This uses the core/dev/spi.h header and implements the spi_init()
function and the various macros for SPI operation. ssi.h contains all of
the register locations and information.
This implementation is not very versatile, mostly because I don't how to
make it flexible in the contiki system. It supports pin muxing for the
four spi pins, but other than that picks sensible defaults.
The SPI macros (like SPI_READ()) are defined in
cpu/cc2538/spi-arch.h. In order to use the SPI driver, add the following
includes to your project:
#include "spi-arch.h
#include "dev/spi.h"
2013-09-27 17:46:15 -04:00
Oliver Schmidt
2263c1aa55
- Optimized LAN91C96 driver for speed and size.
...
- Speed: The primary byte copy loops are reduzed to the bare minimum by adjusting the base pointer 'ptr' and loop register 'y' in such a way that the 'y' overflow matches the low byte of the loop size.
- Introduced a loop for setting the MAC address.
Additional minor fix:
- Properly start self modification with first location.
2013-09-12 23:32:26 +02:00
Oliver Schmidt
ea08635ca4
Optimized CS8900A driver for speed and size.
...
- Speed: The primary byte copy loops are reduzed to the bare minimum by adjusting the base pointer 'ptr' and loop register 'y' in such a way that the 'y' overflow matches the low byte of the loop size.
- Size: Factored out all repeated code into subroutines. Introduced a loop for setting the MAC address.
Additional minor changes:
- Activate frame reception as last step of initialization after CS8900A configuration.
- Properly set internal address bits used by the CS8900A.
2013-09-12 23:32:25 +02:00
Brad Campbell
982ca0fb46
Updates CC2538 GPIO
...
1. Fixes two of the comments to GPIO macros. They were copied but not
updated.
2. Adds SET and CLR macros for controlling GPIO pins.
2013-09-11 21:39:56 -04:00
Nicolas Tsiftes
7987a6dac7
Merge pull request #328 from g-oikonomou/cc2538-uart-config
...
Make the CC2538 UART driver more configurable
2013-08-09 10:20:36 -07:00
George Oikonomou
460d5bcb5d
Fix cc2530 UART1 init bug
...
Fixes #286
2013-08-09 16:09:12 +01:00
George Oikonomou
cb075dec65
Disable SDCC warnings 110 and 126
...
Those two warnings are optimisation-related
* 110 warns that an always-false if branch has been optimised out
* 126 warns about unreachable code which also gets optimised out
In disabling those warnings, we make the build less cluttered
2013-08-09 15:57:49 +01:00
George Oikonomou
20f06e3271
Support verbosity control for 8051-based platforms
2013-08-09 15:57:21 +01:00
George Oikonomou
c89450a233
Change to sdar from the now deprecated sdcclib
2013-08-09 15:56:16 +01:00
George Oikonomou
b025759665
Don't redirect sdld output to dev/null
...
This was used in the past because sdld was
very verbose when linking banked hex files. New
sdld versions do not exhibit this level of
verbosity and therefore the redirect can be
stopped
2013-08-09 15:56:15 +01:00
George Oikonomou
1b0470687b
Change the cc2531 usb stick descriptor
...
The CC2531 USB stick now identifies itself as a
'Texas Instruments CC2531 USB Dongle' and uses a
TI-assigmed VID:PID. The VID:PID is now configurable
in contiki- or project-conf.h
2013-08-09 15:51:58 +01:00
George Oikonomou
0a7094bc39
Remove leftover make targets
...
The sensinode platform does not support .upload and .serialdump
Their presence in the makefile has confused in the past confused
some users. This commit removes them
The commit also removes the $(OBJECTDIR)/%.rel: %.cS recipe which
is not used by either 8051 platform and is probably broken anyway,
since it has been unmaintained for years
2013-08-09 15:48:05 +01:00
George Oikonomou
6c6013b898
Make the CC2538 UART driver more configurable
...
* We can now very easily switch between UART0 and UART1 through a define
* We can also configure the UART RX and TX port/pin through defines
2013-08-09 12:20:25 +01:00
George Oikonomou
c3b5d4f5e3
Add support for verbosity control
2013-08-07 15:26:22 +01:00
Nicolas Tsiftes
a9f0907640
Merge pull request #304 from frtos-wpan/rf230bb-merged
...
cpu/avr/radio/rf230bb/rf230bb.c (rf230_transmit): extend comment on tx s...
2013-08-05 00:24:35 -07:00
Oliver Schmidt
6ab336f55f
Several minor consistency improvements.
2013-07-31 00:55:31 +02:00
Oliver Schmidt
3c6c7381d8
Suppress some usual warnings.
2013-07-31 00:29:52 +02:00
Oliver Schmidt
8d23d1b0bb
Support the recently added verbosity control.
2013-07-31 00:15:38 +02:00
Oliver Schmidt
116c3f119b
unistd.h doesn't seem to be necessary but breaks the MS VC build.
2013-07-31 00:02:29 +02:00
Werner Almesberger
be0a296049
cpu/avr/radio/rf230bb/rf230bb.c (rf230_transmit): extend comment on tx sequence
...
Explain that the transmission is intentionally started before copying the
frame to the buffer.
2013-07-28 18:43:29 -03:00
Mariano Alvira
5d19de3dbf
Merge pull request #266 from ismb-pert/fix-mbxxx
...
mb851 platform is now the more generic mbxxx. STM32W_CPUREV environment variable is used to select the variant of STM32W to use.
2013-07-26 07:38:11 -07:00
stefano pascali
36e7db42de
Some little refactor
2013-07-19 16:15:55 +02:00
stefano pascali
b43ce0f677
Travis-ci tweaks, added CPUREV to 01 regression test, needed by mbxxx platform
2013-07-12 17:07:04 +02:00
stefano pascali
fcb09d5d30
Fixed mbxxx platform
2013-07-11 17:56:17 +02:00
Mariano Alvira
6307f3ff95
mc1322x: make uart buffer sizes configurable from contiki-conf.h
2013-07-04 14:09:40 -04:00
Oliver Schmidt
ad34b714cd
Merge pull request #287 from oliverschmidt/master
...
The current cc65 build doesn't require this workaround anymore.
2013-06-27 15:38:48 -07:00
Oliver Schmidt
fb1de74dc4
The current cc65 build doesn't require this workaround anymore.
2013-06-28 00:36:33 +02:00
Peter A. Bigot
5fc0575e99
Makefile.include: support make clean all
...
Historically $(OBJECTDIR) was created when Makefile.include is read. A
consequence is that combining "clean" with "all" (or any other build
target) results in an error because the clean removes the object
directory that is required to exist when building dependencies.
Creating $(OBJECTDIR) on-demand ensures it is present when needed.
Removed creation of $(OBJECTDIR) on initial read, and added an order-only
dependency forcing its creation all Makefile* rules where the target is
explicitly or implicitly in $(OBJECTDIR).
2013-06-20 17:45:41 -05:00
Oliver Schmidt
79bb5ea73f
Removed some more old RCS tags from the Contiki source tree.
2013-06-13 15:54:26 +02:00
Oliver Schmidt
cbce31cb59
Another small addition for platform 'Atari XL'.
2013-06-02 23:36:28 +02:00
Robert Quattlebaum
36fbbe48aa
Merge pull request #244 from darconeous/pull-requests/cpu-native-tapdev-ipv6-fix
...
native/net/tapdev: Fix for new `UIP_CONF_IPV6` handling.
2013-05-21 17:42:44 -07:00
Nicolas Tsiftes
a445c4020d
Merge pull request #153 from darconeous/pull-requests/cpu-avr-bootloader
...
avr/bootloader.c: Now compatible with bootloaders which always run first
2013-05-20 05:49:13 -07:00
Robert Quattlebaum
09eec82d08
Merge pull request #134 from darconeous/pull-requests/cpu-avr-avrdude-mcu
...
cpu/avr: Added "AVRDUDE_MCU" configuration parameter.
2013-05-19 17:35:26 -07:00
Robert Quattlebaum
9c70e0e5cc
native/net/tapdev: Fix for new `UIP_CONF_IPV6` handling.
2013-05-19 17:27:30 -07:00
Robert Quattlebaum
674f70b6c3
cpu/avr: Added "AVRDUDE_MCU" configuration parameter.
2013-05-19 14:23:31 -07:00
Adam Dunkels
aaac20a950
Merge pull request #225 from tecip-nes/pic32_minor_reorganization
...
Pic32 minor reorganization
2013-05-19 14:22:14 -07:00
Robert Quattlebaum
9c17a542a7
avr/bootloader.c: Now compatible with bootloaders which always run first.
...
The boot loader now knows when to go into bootstrap mode by
looking for a specific EEPROM value. Also updated code style
to match Contiki code style guidelines.
2013-05-19 08:21:16 -07:00
Robert Quattlebaum
535e90343c
Merge pull request #144 from darconeous/pull-requests/settings-for-all-targets
...
core/lib/settings: Generalized settings manager to work on any platform
2013-05-18 12:03:09 -07:00
Robert Quattlebaum
b8c0f2de6c
cpu/native: Add file-backed simulated EEPROM to native cpu.
...
This patch removes a defunct EEPROM implementation from the native
platform and provides a new EEPROM implementation for the native cpu.
The previous implementation appears to be vestigal.
This is useful for testing code which uses the EEPROM without running
the code on the actual hardware.
By default the code will create a new temporary file as the EEPROM
backing, reinitializing each time. If you would like to preserve the
EEPROM contents or specify a specific EEPROM file to use, you can set the
`CONTIKI_EEPROM` environment variable to the name of the EEPROM file you
wish to use instead. If it already exists, its contents will be used.
If it does not already exist, it will be created and initialized by
filling it with `0xFF`---just like a real EEPROM.
A new example is also included, which was used to verify the correctness
of the implementation. It can easily be used to verify the EEPROM
implementations of other targets.
2013-05-18 10:29:41 -07:00
Giovanni evilaliv3 Pellerano
c33d51e762
pic32 minor cleanups
2013-05-17 14:32:39 +02:00
Adam Dunkels
59a8df14a8
Merge pull request #189 from sieben/markdown
...
Update to markdown
2013-05-16 00:24:25 -07:00
François Revol
7967779e6c
tapdev: Fix using an uninitialized buffer
2013-04-20 14:42:19 +02:00
George Oikonomou
704309cfd4
Change the InfoPage Location of the IEEE address
2013-04-17 15:44:01 +01:00
George Oikonomou
8b5b2bd4d8
CC2538 Documentation typo and grammar fixes
2013-04-17 15:41:41 +01:00
George Oikonomou
007e113ea9
Improve handling of CDC ACM line state
...
- For the CC2538, simplify handling of USB_CDC_ACM_LINE_STATE
events. Ignore the Carrier Control (RTS) bit when receiving
a SET_CONTROL_LINE _STATE request, we are a full duplex device.
- Improve behaviour of the CC2531 USB stick when there is no
process on the host to read IN data. Basically, we adopt the
CC2538 approach and we only send data when a DTE is present
2013-04-16 15:49:05 +01:00
George Oikonomou
40f49948e6
New Platform: TI CC2538 Development Kit
...
This commit adds cpu, platform and example files,
providing support for running Contiki on TI's cc2538 DK
2013-04-06 21:07:31 +01:00
Rémy Léone
e6bd4f1dde
Rename to md
2013-03-26 23:15:37 +01:00
Rémy Léone
7b40a568a6
Update to markdown
...
- Spellchecking
- Update plain text to github markdown
2013-03-26 16:55:19 +01:00
Robert Quattlebaum
28a1e40ebd
core/lib/settings: Generalized Settings Manager to work on any platform
...
This commit moves the Settings Manager from the AVR codebase
into the Contiki core library. Any platform that implements
the Contiki EEPROM API can now use the Settings Manager's
key-value store for storing their persistent configuration info.
The Settings Manager is a EEPROM-based key-value store. Keys
are 16-bit integers and values may be up to 16,383 bytes long.
It is intended to be used to store configuration-related information,
like network settings, radio channels, etc.
* Robust data format which requires no initialization.
* Supports multiple values with the same key.
* Data can be appended without erasing EEPROM.
* Max size of settings data can be easily increased in the future,
as long as it doesn't overlap with application data.
The format was inspired by the [OLPC manufacturing data format][].
Since the beginning of EEPROM often contains application-specific
information, the best place to store settings is at the end of EEPROM
(the "top"). Because we are starting at the end of EEPROM, it makes
sense to grow the list of key-value pairs downward, toward the start of
EEPROM.
Each key-value pair is stored in memory in the following format:
Order | Size | Name | Description
--------:|---------:|--------------|-------------------------------
0 | 2 | `key` | 16-bit key
-2 | 1 | `size_check` | One's-complement of next byte
-3 | 1 or 2 | `size` | The size of `value`, in bytes
-4 or -5 | variable | `value` | Value associated with `key`
The end of the key-value pairs is denoted by the first invalid entry.
An invalid entry has any of the following attributes:
* The `size_check` byte doesn't match the one's compliment of the
`size` byte (or `size_low` byte).
* The key has a value of 0x0000.
[OLPC manufacturing data format]: http://wiki.laptop.org/go/Manufacturing_data
2013-03-20 11:57:13 -07:00
Oliver Schmidt
6ba28bf74f
Merge pull request #180 from mmuman/cleanup-and-fixes
...
Cleanup and fixes
2013-03-20 02:37:24 -07:00
François Revol
22bcb07c61
tapdev: Log to stderr; add tracing
...
Use stderr for logging to avoid polluting stdout.
Add some DEBUG tracing.
2013-03-19 19:41:20 +01:00
Adam Dunkels
a5046e83c7
Cleanup and refactoring of the STM32w port
...
This is a general cleanup of things like code style issues and code structure of the STM32w port to make it more like the rest of Contiki is structured.
2013-03-18 13:31:26 +01:00
RongHQ
12b3d02ba1
Fix a syntax error in /cpu/cc253x/dev/uart0.c
2013-03-16 19:41:42 +08:00
Oliver Schmidt
a0e2120fdb
Added configurations of the new resolver.
2013-03-14 23:17:59 +01:00
George Oikonomou
cc37a1e46e
Fix cc2530 DMA priority define values
...
Fixes #156
2013-03-12 15:39:59 +00:00
Adam Dunkels
39e5a8c6dc
Merge pull request #80 from darconeous/mdns-resolv
...
Adds IPv6 and MDNS domain name resolution.
2013-03-10 12:58:39 -07:00
Adam Dunkels
c7ef7198a8
Merge pull request #85 from darconeous/native-target-osx
...
Various updates to the minimal-net platform.
2013-03-10 12:48:07 -07:00
Robert Quattlebaum
1d113f52ad
core/net/uip: Rename `uip_ethaddr` to `uip_lladdr`.
...
There isn't really a good reason I can think of for these
to be different between IPv4 and IPv6.
2013-03-10 11:39:11 -07:00
Nicolas Tsiftes
a8dc74bda8
Merge pull request #133 from darconeous/pull-requests/cpu-avr-gc-sections
...
cpu/avr: Make sure that GCC removes all unused symbols.
2013-03-07 12:52:24 -08:00
Mariano Alvira
ab8fe95864
Revert "Merge pull request #120 from Jeff-Ciesielski/stm32_cl"
...
This reverts commit 029bc0ee27
, reversing
changes made to a7b3e99644
.
This uses LGPL libopencm3. While the patch doesn't include the code,
the resulting binary would force the release of all code as LGPL.
2013-03-02 08:11:28 -05:00
Robert Quattlebaum
67a39618eb
cpu/avr: Make sure that GCC removes all unused symbols.
...
This magic comes from the `--gc-sections` linker flag, which turns on garbage collection for unused input sections. The compiler flags `-ffunction-sections` and `-fdata-sections` make sure that each function and each static data definition have their own section. The result is that GCC can prune away all unused symbols, reducing the size of the resulting executable.
These optimizations may be disabled by setting the Makefile variable
`SMALL` to zero.
2013-02-28 21:59:19 -08:00
Robert Quattlebaum
38b2863831
Update cpu/native/Makefile.native
2013-02-26 11:29:04 -08:00
Nicolas Tsiftes
42e4b2b02a
Merge pull request #143 from idelamer/master
...
Bug fix for Issue #88
2013-02-24 15:26:38 -08:00
Mariano Alvira
029bc0ee27
Merge pull request #120 from Jeff-Ciesielski/stm32_cl
...
Add initial support for STM32F1x Connectivity Line devices
2013-02-24 15:08:57 -08:00
Oliver Schmidt
c6620e47aa
Merge pull request #131 from oliverschmidt/master
...
Two minor retro-specific changes.
2013-02-16 15:12:52 -08:00
Oliver Schmidt
61b90c0126
We actually need PROJECT_OBJECTFILES and PROJECT_LIBRARIES for retro builds too.
2013-02-16 22:57:50 +01:00
Nicolas Tsiftes
2eb3c2a492
Merge pull request #94 from alignan/master
...
Fixes Issue #93
2013-02-16 13:46:09 -08:00
Ivan Delamer
c22838b9d3
Enable Timer1 on Raven so that interrupts coming from radio, which are
...
connected to input capture, fire again.
2013-02-15 16:08:37 -07:00
Oliver Schmidt
98060c1eab
Moved from last cc65 release (2.13.3) to recent cc65 snapshot (2.13.9).
...
Relevant cc65 changes...
General:
- The compiler generates "extended" dependency info (like gcc) so there's no need for postprocessing whatsoever :-)
- The linker is very pernickety regarding the ordering of cmdline options so a custom linker rule is necessary :-(
Apple2:
- The various memory usage scenarios aren't specified anymore via separate linker configs but via defines overriding default values in the builtin linker config.
Atari:
- The builtin linker config allows to override the start addr so there no more need for a custom linker config.
- The C library comes with POSIX directory access. So there's no more need for for a custom coding.
CBM:
- The C library comes with POSIX directory access. So there's no more need for for a custom coding.
2013-02-14 15:42:43 +01:00
Jeff Ciesielski
6b97fa8382
stm32f1x_cl: Fix stm32f107 linker script
...
This is a critical fix which adds inclusion of the entire data/bss
section to the output ELF file. Without it, the BSS section will not
be zeroed out
2013-02-09 23:54:14 -08:00
Oliver Schmidt
c7f986faf5
Merge pull request #121 from oliverschmidt/master
...
Several minor adjustments.
2013-02-08 17:04:04 -08:00
Oliver Schmidt
9938cb6838
Adjusted names.
2013-02-09 01:58:37 +01:00
Jeff Ciesielski
5c6018f0e2
stm32f1x_cl: Add initial support for STM32F1x connectivity line
...
This currently supports the stm32f107, but support will be added for
the F105 shortly (missing a linker script and I can't properly test
without a devkit).
2013-02-06 15:41:50 -08:00
Mariano Alvira
fb8bbf37cf
Use the RTC only as the main timer.
...
This is a major change to how the main tick interrupt is handled on
the mc1322x platforms. Instead of using two timer resources, TMR0 and
RTC, this patch unifies all the timers to use the RTC. This is enabled by
implementing etimers as scheduled rtimers. The main advantage (aside
from freeing TMR0 for general use) is have the Contiki timebase come
from the same source that will be used for sleeping and wakeup.
2013-02-03 15:15:05 -05:00
Mariano Alvira
ad55ccdec4
add working routines to turn the mc1322x radio on and off
2013-02-03 14:48:38 -05:00
Oliver Schmidt
69317ad1db
Renamed retro 'dhcp-client' to 'ipconfig' as it can as well be used for interactive manual configuration.
2013-02-01 21:20:21 +01:00
Oliver Schmidt
74dfff972f
Do not reject frames with a length exactly equal to the uIP bufer size.
2013-01-30 23:39:01 +01:00
Robert Quattlebaum
a571b663b0
platform/minimal-net: Better, more seamless support for OS X.
...
This patch enables automatic route setup and cleanup when
starting and stopping the minimal-net target on OS X.
Both IPv4 and IPv6 are supported.
Using the minimal-net target on OS X was absolute hell
before I came up with this patch. Now it is painless.
2013-01-30 09:17:30 -08:00
Robert Quattlebaum
092b6f3baa
platform/minimal-net: Implement better idle behavior.
...
The minimal-net target, as currently written, wakes up the
CPU every millisecond to check for packets, and will only
react in real-time to input from stdin. If you are running
this on a laptop battery, your battery will quickly drain.
This change allows the CPU to idle when there is literally
nothing to do while still being responsive to input from
stein and/or incoming packets. This fix should significantly
improve performance while significantly improving power
usage. Win-win.
Also added `_xassert()` implementation so that the contiki-
provided `assert()` macro will work properly when used
on this platform.
2013-01-30 09:17:29 -08:00
Oliver Schmidt
e88997b71c
Minor README updates.
2013-01-29 22:44:37 +01:00
Antonio Lignan
2cf4e30b11
Baudrate now is configured taking into account the MCU frequency, instead of using fixed values for 8MHz freq
2013-01-29 12:23:23 +01:00
Oliver Schmidt
1a5e20bc5f
Remove tab chars from retro C sources.
2013-01-28 23:43:08 +01:00
George Oikonomou
eea6b9051d
Removed a stray leds_toggle
2013-01-09 22:46:20 +00:00
Adam Dunkels
326781ef43
Merge pull request #74 from malvira/maca-dummy-rx
...
Receive packets in a dummy_rx when the maca packet pool is
2013-01-06 14:10:23 -08:00
Mariano Alvira
a53e653bbf
Receive packets in a dummy_rx when the maca packet pool is
...
empty. These packets get dropped.
2013-01-06 15:12:07 -05:00
Mariano Alvira
64ded5aecc
run the linker script through CPP so that the stack sizes can be
...
changed using CONF parameters via DEFINES (e.g. SYS_CONF_STACK_SIZE
4096)
2013-01-05 17:08:59 -05:00
Giovanni `evilaliv3` Pellerano
ee556dcf14
minor corrections to adhere contiki code style guidelines
2012-12-21 12:36:29 +01:00
Giovanni `evilaliv3` Pellerano
f68df3a81c
added support for pic32 (PIC32MX795F512L)
2012-12-17 09:14:23 +01:00
George Oikonomou
380ee3bae9
Code style fixes: cc253x
2012-12-16 19:28:56 +00:00
George Oikonomou
874bec26a5
Code style fixes: cc2430
2012-12-16 19:28:55 +00:00
Arngrimur Bjarnason
b533a683c3
Changed makefile. Removed extra slash
2012-12-10 20:41:43 +01:00
Mariano Alvira
f60a00b93e
the contiki-maca process should wait for a poll event
2012-12-02 14:26:51 -05:00
Mariano Alvira
b3bb3ff53d
fix very incorrect insert_at_rx_head; the bugged version would make
...
the rest of the rx list dangling.
this is used to insert the ack packet needed by the upper layers in
the netstack.
2012-12-02 14:25:39 -05:00
Mariano Alvira
f7d1d78ac9
disable pad keeper when using ADC pin; otherwise you'll see a 20k input
...
impedance.
2012-11-30 10:44:26 -05:00
Adam Dunkels
db41a51ae6
Make gcc default LD, and allow override with LD_OVERRIDE
2012-11-21 19:46:31 +01:00
Ilya Dmitrichenko
d0f18e5d04
Fixed LDFLAGS for cross-compiling of "native"
2012-11-21 18:09:29 +00:00
Ilya Dmitrichenko
092c69639c
Enable `native` target for cross-compiling -
...
by now it would have worked if you set CC via
command line (e.g. `make CC=clang`, though it
wouldn't work when CC is set in the platform
makefile which includes `Makefile.native`.
2012-11-21 18:09:10 +00:00
Mariano Alvira
03ab3fe317
Newer and cleaner TARGET=econotag as well as robust mc13224v
...
configuration system.
(also deprecate TARGET=redbee-econotag)
- mc13224v now automatically probes hardware config for buck converter
and 32kHz crystal as well as automatically monitors battery voltage
and manages the buck accordingly.
- new flashed based config system for mc13224v parameters such has
radio modes (demod, autoack), nvmtype, mac address, channel and
power.
- considerably cleaned up econotag platform code (suffered from severe
case of bit-rot)
2012-11-19 19:16:29 -05:00
Mariano Alvira
2c9a538582
Merge branch 'master' of git://git.devl.org/git/malvira/libmc1322x into bump-libmc1322x
...
bump libmc1322x to 7bee48243c
Conflicts:
cpu/mc1322x/board/Makefile.board
cpu/mc1322x/lib/include/uart.h
cpu/mc1322x/lib/uart1.c
cpu/mc1322x/lib/uart2.c
cpu/mc1322x/src/default_lowlevel.c
2012-11-18 18:27:39 -05:00
Etienne Duble
7905316c54
Fix: stm32w flasher for Ubuntu 12.04 and later
2012-11-09 14:14:57 +01:00
Etienne Duble
ecdbbaec9a
Fix: handle stm32f-based serial interfaces (/dev/ttyACMx)
2012-11-09 14:00:16 +01:00
George Oikonomou
79cffa030f
cc2531: USB CDC-ACM code style fixes
...
Closes #18
2012-11-01 17:42:04 +00:00
George Oikonomou
1a0f01ccc4
cc253x: Config to swap between UART and USB I/O
...
See Pull Request #18
2012-11-01 17:41:57 +00:00
Philippe Rétornaz
eabaa0c8e4
cc253x: DMA Changes
...
- Fixed DMA irq flag clearing
- Added a dma_reset helper
See Pull Request #18
2012-11-01 17:41:49 +00:00
Philippe Rétornaz
898bd07810
cc253x: optionally push bits in p2 interrupt
...
See Pull Request #18
2012-11-01 17:41:46 +00:00
Philippe Rétornaz
0a6e65acdf
cc2531: USB changes:
...
- usb cdc-acm:
* implement get line coding
* use printf only when debugging
* Add events
- usb-core: do not force debugging
See Pull Request #18
2012-11-01 17:41:41 +00:00
George Oikonomou
c1d72475d7
cc253x: Renamed P2 interrupt-related files for better consistency
...
See Pull Request #18
2012-11-01 17:41:38 +00:00
George Oikonomou
c60f0b4349
cc253x: P2-related routines are now bankable
...
We keep the ISR in its own file and move everything else
to a different one, so that we only have to keep the ISR
in HOME
See Pull Request #18
2012-11-01 17:41:32 +00:00
George Oikonomou
d9d4fa168d
cc253x: Renamed the P2 ISR
...
This is mainly a naming convention thing, we want to have 'isr'
as part of the name, instead of 'int'. We also want port_2 instead
of p2 because we already had port_1
See Pull Request #18
2012-11-01 17:41:28 +00:00
George Oikonomou
fea4970142
cc253x: Configurable linkage for the P2 ISR
...
See Pull Request #18
2012-11-01 17:41:24 +00:00
Philippe Rétornaz
ba96408f37
cc253x: Add USB support to the compilation scripts
...
See Pull Request #18
2012-11-01 17:41:21 +00:00
Philippe Rétornaz
d93fee612d
cc2531: Add USB driver
...
See Pull Request #18
2012-11-01 17:41:17 +00:00
Philippe Rétornaz
ddc8120d7c
cc253x: Add p2 interrupt handler
...
The P2 Interrupt is shared across many periferal (I2C, USB, GPIO).
This adds a generic interrupt handler on which the differents drivers
can register a handler.
See Pull Request #18
2012-11-01 17:41:11 +00:00
Philippe Rétornaz
dec34c21ef
cc2531: change cdc-acm descriptor
...
Change to have a real usb VID/PID and better fit the capabilities
of the CC2531 hardware (enpoint size, location).
Compile only if the cdc-acm class is requested.
See Pull Request #18
2012-11-01 17:41:07 +00:00
Philippe Rétornaz
0e55eb0947
cc2531: Copy arm usb framework
...
See Pull Request #18
2012-11-01 17:40:35 +00:00
George Oikonomou
713c2e5974
DOS EOL and indentation fixes (core/ apps/ cpu/)
...
- Removed some DOS EOLs
- Changed some tabs to spaces
- Removed some trailing whitespaces
Part of Pull Request #6
2012-10-30 13:43:51 +00:00
Adam Dunkels
6c8fbd2dff
Merge pull request #11 from adamdunkels/remove-rtl8019
...
Removed old unused RTL8019 code that had license issues
2012-10-29 08:43:59 -07:00
Adam Dunkels
1af22fa4fe
Removed old unused RTL8019 code that had license issues
2012-10-29 16:08:09 +01:00
Mariano Alvira
4087c0785f
remove -g
...
see http://comments.gmane.org/gmane.os.contiki.devel/13869
2012-10-29 10:34:28 -04:00
Adam Dunkels
944537fccf
Removed all old RCS tags in the Contiki source tree. Those RCS tags are not used any more, as we are now using git to manage the Contiki source tree
2012-10-26 15:54:49 +02:00
Niclas Finne
f5c8cff5b2
Made MT stack size configurable
2012-10-23 00:52:52 +02:00
George Oikonomou
d84a97103f
cc2x3x stack debugging macro fix
2012-09-20 15:12:02 +01:00
George Oikonomou
fde1510653
Added definitions for cc2530 DMA-related SFR bits
2012-09-20 15:09:15 +01:00
George Oikonomou
3b0e92168b
Copied cc2530 stack functions to the cc2430 port
2012-09-20 15:09:15 +01:00
George Oikonomou
95b9d4ee29
Sensinode/cc2430 stack depth optimisation
...
This replicates the method used by the cc2530 port
2012-09-20 15:09:15 +01:00
George Oikonomou
cb168da729
Changed the cc2430 sleep_flag to uint8_t
2012-09-20 15:09:15 +01:00
George Oikonomou
fa5a38666b
Removed redundant #else blocks
2012-09-20 15:09:15 +01:00
George Oikonomou
88c6689e38
cc2430: Build with --fomit-frame-pointer
2012-09-20 15:09:15 +01:00
Niclas Finne
767e8bb551
Default value for _DATA20_HEAP_SIZE when using the IAR compiler on MSP430 platforms
2012-09-20 14:01:56 +02:00
Niclas Finne
4630945475
Made the stack and heap size configurable when using the IAR compiler on the MSP430 platforms
2012-09-19 22:49:19 +02:00
George Oikonomou
ee7af77ca9
Reworked the cc2530 stack debugging facilities:
...
- Moved to their own file
(so we can later copy the entire thing over to cc2430)
- Renamed the functions
(for naming convention reasons)
- The entire thing can be enabled/disabled
- Added a couple more macros
- Hooked into main()
2012-09-07 17:40:17 +01:00
Philippe Rétornaz
9a63e8c027
cc253x: Add stack monitoring helpers
2012-09-07 17:32:54 +01:00
Philippe Rétornaz
48d99f15c8
cc253x: fix dma interrupt enable flag
2012-09-07 17:32:54 +01:00
George Oikonomou
c6ec22c4c8
cc2530: Added a method to maximise stack depth
...
This was oringinally contributed/reported/discussed/patched by
Philippe Retornaz (EPFL) but it's implemented
in a more configurable fashion here.
2012-09-07 17:32:53 +01:00
Philippe Rétornaz
666ff6ca55
cc253x: use a uint8_t for sleep_flag
...
__bit variables must be located after the 0x20 address
This force the stack to start after 0x20, thus decrease
the stack size by a considerable amount.
2012-09-07 17:32:10 +01:00
Philippe Rétornaz
44bcabe89c
cc253x: Change CFLAGS
...
This add -fomit-frame-pointer by default, it decrease sliglty the
stack usage when several function call are nested.
On some specific case 30 bytes could be saved on the stack.
2012-09-07 17:32:10 +01:00
George Oikonomou
8699f7741d
Fixed typos and a stray printf. Adjusted comments
2012-09-07 17:31:25 +01:00
Ivan Delamer
b43dad00b0
Cleaned up RF230BB, and refactored FRAME_RETRIES and CSMA_RETRIES
...
#defines.
2012-09-04 11:12:18 -06:00
Ivan Delamer
2e72ec3594
Place ATmega1281 define in correct section (it does have compare C
...
unit, avoid duplicate define and compiler warning).
2012-09-01 15:22:13 -06:00
Ivan Delamer
5636357243
Fix RF230 transition: RX_AACK_ON -> TX_ARET_ON (go through PLL_ON,
...
as per datasheet). Tested on RF230 and 128RFA1 (RF231).
2012-09-01 15:20:00 -06:00
George Oikonomou
26a87ee9cb
Improved handling of cc2x3x rf_flags
2012-07-11 10:53:14 +01:00
George Oikonomou
43f2790357
Added channel_get() to the cc2x3x RF drivers
2012-07-11 10:53:14 +01:00
George Oikonomou
d66241fd97
Bugfixed the cc2530 LOW_POWER_RX configuration
...
Report and fix by Tom Xiao
2012-07-11 10:53:14 +01:00
George Oikonomou
62fbd389d8
Renamed a cc253x SFRX to stop namespace conflicts
...
The TR0 SFRX can not use the name TR0 because it
conflicts with TCON.TR0 on the default 8051.
See SDCC bug 3513300
2012-07-11 10:53:14 +01:00
George Oikonomou
4b73b48f60
Fixed the cc2530 RSSI adjustment
2012-07-11 10:53:14 +01:00
Ivan Delamer
17a62a649c
ATmega128RFA1 bug fix: no interrupt pin used (embedded radio).
...
Enabling interrupt caused MCU reset if using pin as GPIO.
2012-07-10 14:36:47 -06:00
Niclas Finne
418a5772e6
Removed leds debug output
2012-06-07 10:35:22 +02:00
George Oikonomou
47db065034
Bugfixed the cc253x UART0 init (Thanks, Deng Jian)
...
The flush instruction was resetting the stop bit level to 'low'
2012-06-06 15:25:57 +01:00
David Kopf
e9a55cc222
Enable check on received length to prevent buffer overflow. Thank you Cooja!
2012-05-28 13:02:23 -04:00
George Oikonomou
259b497122
Minor Sensinode build cleanup
2012-05-16 15:22:31 +01:00
George Oikonomou
1f7171f943
Adjust cc2x3x ports to the new clock API
2012-05-16 15:22:31 +01:00
George Oikonomou
0d4b90c42b
cc2530 watchdog improvements and cleanup
2012-05-16 15:22:31 +01:00
George Oikonomou
274a5ebb9c
Fixed a typo which was preventing the cc253x watchdog from starting
2012-05-16 15:22:30 +01:00
Laurent Deru
56914963ef
Reactivate flash protection after maca init
2012-05-09 10:24:38 -04:00
Mariano Alvira
a4813d815f
use --gc-sections instead of -gc-sections
2012-05-06 12:19:20 -04:00
Mariano Alvira
4acad929f0
add gc-sections, roughly 4kB savings.
2012-05-06 09:24:06 -04:00
David Kopf
d6dc216e02
Reorder includes to prefer platform routines. Remove redundant RPL define.
2012-04-27 16:54:09 -04:00
George Oikonomou
dd26accc07
We can now use SDCC's __nonbanked feature
...
This allows us to reduce CODE footprint of SDCC projects
built with --model-huge. Use carefully!
* Added a facility which allows us to enable/disable the
feature from the CPU dir (CC_CONF_NON_BANKED_OPTIMIZATION)
* Added the CC_NON_BANKED keyword to some platform files
(expands to __nonbanked)
* Started using this for some examples
2012-04-26 15:28:43 +01:00
Adam Dunkels
b85bc3379c
Bugfix in clock_wait() declaration. Various style fixes.
2012-04-22 20:54:29 +02:00
George Oikonomou
e95f94a9a8
Added support for reading MAC from the cc253x flash
...
We still use the primary location by default (Info Page) but
this is now configurable. This change is useful for users who
wish to specify their own MAC address. Since the Info Page is
read-only, they need to be able to use the secondary location
2012-04-20 16:03:38 +01:00
George Oikonomou
29090a3dda
The cc253x Makefile specifies SoC flavor
...
This will help us slowly add better support for smaller SoCs
instead of just assuming that all cc253x SoCs are F256
- We build for F256 by default but the project Makefile can override this
- We currently ignore this when passing --code-size. This is a ToDo
- The bank allocator always assumes 7 banks. Once we fix --code-size above this will be irrelevant
2012-04-20 16:03:38 +01:00
George Oikonomou
6fb48174ba
Fixed a documentation typo
2012-04-20 16:03:37 +01:00
Niclas Finne
1b13b69814
Added support for mspgcc 4.6+ that no longer supports generic MCU identifiers such as msp430x1611
2012-04-10 16:05:10 +02:00
Niclas Finne
57a166c3db
Corrected compiler flags for the IAR compiler
2012-04-10 15:27:44 +02:00
David Kopf
cac4e9a222
Add clock_delay_us and clock_set_seconds to clock.h. Modify clock_wait to use clock_time_t.
...
Remove the troublesome avr/dev/delay.* files.
Add PLATFORM_NAME and combine the confusing *_REVISION defines into a single PLATFORM_TYPE
2012-04-09 15:49:53 -04:00
David Kopf
40bd020394
Fix wrong register addresses.
2012-04-09 09:58:12 -04:00
George Oikonomou
57969259ce
cc2x3x clock_delay(len) now delays for approx. len usecs
2012-04-03 16:26:11 +01:00
George Oikonomou
3cb26adeda
Added an ASM(foo) macro for cc243x
2012-04-03 16:26:11 +01:00
George Oikonomou
242e02658f
The cc2530 UART driver was sending a 0 down the line on init
2012-04-03 16:26:10 +01:00
George Oikonomou
b3de052e01
Ported the stack-friendly clock ISR code over from cc243x to cc253x
2012-04-03 16:26:10 +01:00
George Oikonomou
11a7f644ac
Comment rewording and formatting
2012-04-03 16:26:10 +01:00
George Oikonomou
ce17fa131c
Stack-friendly cc243x clock ISR enabled by default
...
This new approach (CLOCK_CONF_ACCURATE=0) was not as inaccurate
as originally thought. In fact, it has pretty much the same
accuracy as the old, stack-hungry version.
* Renamed the define from CLOCK_CONF_ACCURATE (1: old) to
CLOCK_CONF_STACK_FRIENDLY (1: new) to stop implying
that one is more accurate than the other.
* Using CLOCK_CONF_STACK_FRIENDLY by default.
2012-04-03 16:26:10 +01:00
George Oikonomou
924fe934c1
Deleted obsolete macros. Minor formatting
2012-04-03 16:26:10 +01:00
George Oikonomou
ffa3a1c4c3
cc2x3x clock driver cleanup
...
* Bit-Addressable SFRs are now accessed as such,
instead of (N)OR-ing the byte
* A routine was declared as CCIF but not defined as such. Fixed
* Deleted a leftover duplicate define
* Formatting
* Comment updates and clarifications
2012-04-03 16:26:10 +01:00
simonduq
930c7c25bc
fixes in mb851 and stm32w108: erroneous linking with mpu.o, conf file,
...
more printouts in main when ipv6 is used, and a target for memory
profiling taking stm's gnu.ld static stack size into account
2012-04-03 11:47:30 +02:00
George Oikonomou
5240519dd9
Renamed a config define to better match contiki's naming philosophy
2012-04-02 11:38:54 +01:00
George Oikonomou
bce34e4b9a
For cc2x30, moved CLOCK_CONF_SENCOND to the cpu dir.
...
The value is not really configurable by the platform so having it
in contiki-conf.h didn't make huge sense.
2012-04-02 11:22:19 +01:00
George Oikonomou
d958ee3125
Deleted the old Sensinode 'read mac from flash' routine.
...
Since the introduction of a purpose-written routine, the old
generic one (which was written in asm) was never being used.
There was a configuration directive which allowed us to switch
between the two. All references to this configuration directive
have also been removed.
2012-04-02 11:21:32 +01:00
George Oikonomou
5d8f63a61b
We've not been using the cc2430 converter for a while now
2012-04-02 11:03:49 +01:00
George Oikonomou
7854ee499a
Wrapped cc2x30 SOFT_RESET() macro inside do {...} while(0)
2012-03-29 13:11:04 +01:00
George Oikonomou
5afdd19403
Adjusted check to determine if we are being built with SDCC
...
Since rev #7342 , SDCC defines __SDCC_mcs51 instead of SDCC_mcs51.
We check for either
2012-03-29 13:10:25 +01:00
George Oikonomou
4f1e251603
Some uN_t had crept back in cc2530dk and sensinode.
...
Changed to uintN_t plus a bit of code formatting
2012-03-29 13:10:10 +01:00
simonduq
946f00bf7b
stm32w: added ability to upload and reset all connected boards, and login using MOTE=x
2012-03-26 23:00:44 +02:00
simonduq
95ae5c5d51
avoid unnecessary symbols.c/h copying
2012-03-26 23:00:43 +02:00
George Oikonomou
ad256e5014
New platform: TI cc2530 Development Kit
...
This commits adds support for TI's SmartRF05 Eval. Board with cc2530 EMs
Some initial support for cc2531 USB dongles
2012-03-23 14:41:07 +00:00
George Oikonomou
b7674c3636
Reincarnate the sensinode/cc2430 port
2012-03-23 14:41:07 +00:00
simonduq
e4fb360262
stm32w platforms: contikimac support in the Rime case, with EUI-64
2012-03-20 17:30:59 +01:00
simonduq
5da4463236
adding ducy cycling support to the stm32w-based platforms (patch by Chi-Anh La)
2012-03-20 17:29:58 +01:00
Niclas Finne
ff7a977dc7
Improved support for the IAR compiler for the MSP430 platforms
2012-03-07 23:09:05 +01:00
Niclas Finne
684c3edfa6
Cross compiler interrupt service routine compatibility definitions for MSP430 based platforms based on isr_compat.h by Steve Underwood.
2012-03-07 23:04:52 +01:00
Niclas Finne
2eee14a1d8
Allow compiler flag SMALL to be set to disable SMALL-build. Patch by Andre Frimberger.
2012-03-06 15:35:20 +01:00
Ilya Dmitrichenko
49cd7878e3
Avoid deprecated error on Darwin.
2012-03-02 15:15:47 -05:00
Ilya Dmitrichenko
499d3052ee
Fixed TARGET=native compilation issues on Darwin.
2012-03-02 15:15:42 -05:00
David Kopf
2b7ecefce7
Remove unused SPI initializer flag from AVR. Comment out in the msp-430 template.
2012-02-27 17:05:22 -05:00
Ilya Dmitrichenko
9c99d46e24
Simplified host OS platform detection in Makefiles
2012-02-25 10:09:33 -05:00
David Kopf
deb75d3d97
Several bugfixes
2012-02-21 11:14:52 -05:00
David Kopf
59e459e0e9
Add missing mtarch_stop function
2012-02-21 11:11:53 -05:00
David Kopf
6e45dfe5ff
PROGMEM changes needed for newer avr-gcc compiler
2012-02-21 11:10:57 -05:00
Nicholas J Humfrey
1cda3da17e
Converted u8_t to uint8_t and u16_t to uint16_t in the cpu directory.
2012-02-21 08:33:24 -05:00
Mariano Alvira
68591919e6
mc1322x: add -MMD to Makefile.mc1322x to correctly create dependencies
2012-02-16 11:17:15 -05:00
Mariano Alvira
43062b6d74
mc1322x: change how board.h works to allow default board.h (defaults
...
to econotag)
2012-02-13 10:01:36 -05:00
Mariano Alvira
ee8f2c669e
mc1322x: remove symbols.{c,h}
2012-02-13 10:01:36 -05:00
David Kopf
9d6542d49b
Fix minimal-net webserver6, broken after native border router changes.
2012-02-11 15:03:24 -05:00
David Kopf
38267bfd5a
Webserver-nano: Add page load times, remove workaround code for bug in arm strformat.c, correct the double count of leading zeros there.
2012-02-11 14:58:35 -05:00
David Kopf
987906be97
rf230bb updates: involves setting the 801.15.4 pending bit,
...
0x800000 cpu clock, and a jtag reset bugfix
2012-02-01 14:16:39 -07:00
Ivan Delamer
57e686179c
Improved rf230bb.c synchronization/locking. Removed unnecessary locks
...
during Tx (single-threaded environment). Added protection to Rx thread
from buffer access by ISR.
2012-02-01 13:37:45 -07:00
David Kopf
7ca141b457
Access uart registers directly instead of through intermediate addresses in a RAM struct.
...
Add a platform define to reduce the number of ports supported by the cpu.
2012-01-21 13:49:58 -05:00
Niclas Finne
f26920ae9b
Define the BV macro if not already defined
2012-01-11 08:46:16 +01:00
David Kopf
58298f59db
Add F_CPU=0x800000 option with phase lock to external 32768 Hz crystal
...
Add MCU_CONF_LOW_WEAR option to avoid eeprom writes during development.
2012-01-10 12:42:27 -05:00
Niclas Finne
f3db12c19d
MSP430 setup for f2xxx based on Z1
2012-01-09 14:56:03 +01:00
Niclas Finne
9ffcd53868
Fixed compiler warning (with IAR compiler)
2012-01-09 14:56:00 +01:00
Niclas Finne
3daa822f89
Moved configuration of memcpy workaround to cpu (only needed for an older version of mspgcc)
2012-01-09 14:55:57 +01:00
Niclas Finne
fd81a0d393
Minor cleanup (avoid setting some compiler flags twice)
2012-01-09 14:55:54 +01:00
Niclas Finne
8e1e12dfd3
Ignore SMALL when using IAR compiler
2012-01-09 14:55:48 +01:00
Nicolas Tsiftes
eba64bdc5e
Be more explicit with the relationship between inheritance between MSP430 families.
2012-01-09 14:55:45 +01:00
Niclas Finne
cdfa8708e3
* Added f2xxx for two series (for example z1)
...
* f1xxx is baseline and always included
* Cleaned up the names of uart and spi (no x in names)
* Updated SPI configuration for WiSMote
2012-01-09 14:54:57 +01:00
Niclas Finne
f4f84ffca4
Updated SPI config for faster SPI, split msp430/clock/spi into separate versions for MSP430/MSP430X
2012-01-09 14:54:01 +01:00
Niclas Finne
09082f02fe
Changed clock_delay to use the nop instruction
2012-01-09 14:49:39 +01:00
Niclas Finne
cd4be4927a
Fixed quick dco sync to also work with mspgcc
2012-01-09 14:41:42 +01:00
Niclas Finne
708f9d77d2
Corrected timing for higher CPU speed
2012-01-09 14:41:36 +01:00
Niclas Finne
05b10eb9ce
Initial WiSMote port based on code from Arago Systems.
2012-01-09 12:25:06 +01:00
Niclas Finne
367c82a5ab
added compiler flags and macros for IAR and mspgcc 4.4.5 compilers
2012-01-09 12:24:33 +01:00
David Kopf
b251619a2f
Add wpcap for cygwin/Windows native border router
2012-01-08 13:37:56 -05:00
Fredrik Osterlind
2644057fb2
using dma by default
2011-12-21 10:53:18 +01:00
David Kopf
81af871db9
Bugfix: use 16 bit tick count to adjust clock after sleep
2011-12-01 09:58:55 -05:00
Oliver Schmidt
e38f008b9b
The dependency on the ucontext functions has the potential to keep others from successfully using cpu/native for other platforms. As the Contiki multithreading library typically isn't used at all it's not worth the trouble. So we just limit it to Windows and Linux - where it is known to not only build but actually work. If someone needs the Contiki cpu/native multithreading library on another platform he's certainly welcome to add that platform - hopefully by just activating the codepath that we now made exclusive for Linux for his platform.
2011-11-30 23:41:39 +01:00
David Kopf
fb977cb9ef
Better fix for hardware FCS error on JTAG reset
...
Correct silly error introduced by trying to save two bytes.
2011-11-15 13:24:58 -05:00
David Kopf
31ba84eb75
Improve rf23x cca procesing
...
Fix delay_loop timing bug by using long long calculation.
128rfa1 and rf230 both working with contikimac RDC
2011-11-14 11:49:58 -05:00
David Kopf
d1cd3f213c
Add general unsupported interrupt vector suggested by Daniel Willmann
2011-11-14 11:36:18 -05:00
David Kopf
6eba721af1
Add rtimer_arch_sleep function, enabled with RDC_CONF_MCU_SLEEP
2011-11-14 11:10:35 -05:00
David Kopf
c2364897f8
atmega128rfa1 cca fixes, energest and rimestat macros.
...
Add option to return ACK to RDC layer when in extended mode, based on Georg von Zengen code.
2011-11-08 12:20:22 -05:00
Niclas Finne
bf299b1a07
Fixed splhigh/splx for the IAR compiler
2011-09-27 22:51:28 +02:00
Joakim Eriksson
5b1d9617c4
moved io and signal and IAR-GCC checks from driver files into contiki include file
2011-09-26 10:38:41 +02:00
Joakim Eriksson
95dde73618
fixed Sky platform for IAR compiler
2011-09-11 17:18:02 +02:00
David Kopf
f721f646fa
Adjust sleep time by ticks instead of seconds, proposed by Ivan Delamer
2011-09-10 12:44:49 -04:00
Adam Dunkels
4fd8133aa3
Removed the obsolete MAC_CONF_CHANNEL_CHECK_RATE (now replaced with NETSTACK_CONF_RDC_CHANNEL_CHECK_RATE)
2011-09-05 20:42:19 +02:00
Mariano Alvira
43910c1be7
don't worry about wraparound in rtimer_arch_schedule
2011-09-02 12:36:10 -04:00
Mariano Alvira
6c0bbc492b
change mc1322x rtimers to 32-bit
...
hardcode a close default value for the RTC
2011-09-02 12:32:47 -04:00
David Kopf
dfdae5b02b
This fixes commit 9a1ce7 for spaces instead of ....
2011-08-31 12:08:01 -04:00
David Kopf
470887eddd
Print elf size if ELF_SIZE is defined
2011-08-31 11:50:14 -04:00
David Kopf
9a1ce7cf75
Use enumerated tx return values
2011-08-31 11:40:23 -04:00
David Kopf
5f2b2074f0
Implement WITH_RPL option in makefile
2011-08-28 16:11:48 -04:00
David Kopf
bdec65b889
Fix typos and file endings
2011-08-28 16:04:36 -04:00
David Kopf
94fc40f736
Move LEDONPORTE1 define to contiki-conf.h, fixing typo.
2011-08-24 11:35:58 -04:00
David Kopf
09db159876
128rfa1 cca fix, NETSTACK_RADIO.off now returns 0/1 if radio off/on
2011-08-18 14:36:04 -04:00
David Kopf
53737d9a38
Use correct prescale factor
2011-08-18 13:58:20 -04:00
David Kopf
3ea102050b
Apply patch of Ivan Delamer for atmega1281 @ 4 MHz
2011-08-17 13:16:46 -04:00
David Kopf
36fa735323
Calculate best prescaler based on F_CPU and CLOCK_CONF_SECONDS. Inspired by patch from Ivan Delamer.
2011-08-17 13:15:26 -04:00
maniacbug
0990896f54
Added an .eu target to upload only the eeprom for AVR cpu.
2011-08-16 14:10:48 -04:00
maniacbug
8f0bb86c02
No strict aliasing for AVR
...
AVR build generates numerous aliasing errors. This -f switch silences them.
2011-08-16 14:07:06 -04:00
David Kopf
577215deca
Use 128rfa1 interrupts instead of timing.
...
Generalize DEBUGFLOW macro for use in multiple routines.
2011-08-15 15:06:38 -04:00
David Kopf
50d1086553
Add changes needed for contikimac
2011-08-13 11:38:38 -04:00
David Kopf
03ab525652
Option for nested rtimer interrupts
2011-08-13 11:35:03 -04:00
David Kopf
cdcb2c4744
CCA measurement was always returning busy
2011-08-06 13:48:52 -04:00
David Kopf
b70d2b3163
Remove duplicate code block
2011-08-05 17:34:38 -04:00
David Kopf
c9b19ce655
Change timer setups for arbitrary CLOCK_CONF_SECOND
...
Change raven to 128 ticks and enable 32KHz crystal as default.
2011-08-05 15:14:35 -04:00
David Kopf
e2ad2acde4
Add stk500 platform and changes suggested by Daniel Willmann
2011-08-03 11:18:55 -04:00
David Kopf
6ec85fe079
Add Iris port of Shinta Hatatani
2011-08-03 10:17:59 -04:00
Mariano Alvira
2b9f4e8fed
Merge branch 'master' of git://git.devl.org/git/malvira/libmc1322x
2011-08-01 19:50:46 -04:00
David Kopf
cf3241c5db
Add file needed for rpl border router
2011-07-24 12:07:39 -04:00
David Kopf
0bb585fd60
Replace WEBSERVER by AVR_WEBSERVER
2011-07-24 11:43:17 -04:00
Simon Berg
506eced1bc
Bug fix by Jonathan Chung
2011-07-22 15:07:52 +02:00
Mariano Alvira
485d6716e0
Merge branch 'master' of git://git.devl.org/git/malvira/libmc1322x
...
Conflicts:
cpu/mc1322x/src/default_lowlevel.c
2011-07-18 07:25:19 -04:00
HATATANI Shinta
f4740a062a
IRIS port is working with uIPv6
2011-07-15 16:36:25 +09:00
Mariano Alvira
758fc37307
mc1322x: flush the rx fifos when full
2011-07-12 07:05:04 -04:00
Mariano Alvira
4cf9514aa9
fix gpio initialization for uart2
2011-07-09 14:33:03 -04:00
Mariano Alvira
6d96721ac4
mc1322x: block in uart putc if the TX buffer is full. Can also be
...
configured to drop chars instead with UARTx_DROP_CHARS
2011-07-09 12:46:30 -04:00
Mariano Alvira
e80f9eb4b5
mc1322x: build fixes for uart2
2011-07-08 19:40:42 -04:00
Mariano Alvira
e2d74fa0a5
Merge branch 'master' of git://git.devl.org/git/malvira/libmc1322x into uart-upstream
...
Conflicts:
cpu/mc1322x/lib/include/uart.h
cpu/mc1322x/src/default_lowlevel.c
2011-07-08 19:21:15 -04:00
David Kopf
6ea7250af7
Change ctimer startup order, add multihop to wpcap and minimal-net platform.
2011-06-30 12:12:07 -04:00
David Kopf
c48b7ab78d
Add RPL nodes and border router to minimal-net platform (cygwin only)
2011-06-28 08:19:48 -04:00
David Kopf
6b434a553f
Implement SRAM routine of Georg von Zengen
2011-06-21 13:03:58 -04:00
Joakim Eriksson
af601dfb23
improved support for IAR compiler for z1
2011-06-05 00:21:47 +02:00
Mariano Alvira
33b32c61e9
Only insert an ack packet if the ack request bit is set
2011-06-01 13:47:05 -04:00
Joakim Eriksson
77ec0bfa0f
fixed the z1 platform and generic code used by z1 to work with IAR compiler
2011-05-25 17:21:51 +02:00
Mariano Alvira
724bcbd2d3
Merge remote branch 'libmc1322x/master'
...
Conflicts:
cpu/mc1322x/src/default_lowlevel.c
2011-05-14 21:19:47 -04:00
Joakim Eriksson
fd75050c67
Merge branch 'master' of ssh://contiki.git.sourceforge.net/gitroot/contiki/contiki
2011-05-13 11:53:45 +02:00
Joakim Eriksson
2c16538e6a
fixed support for IAR compiler
2011-05-13 11:52:42 +02:00
Salvatore Pitrulli
7a48110067
STM32W flasher utilities for Linux and Windows merged into a single folder.
2011-05-10 19:26:33 +02:00
Mariano Alvira
0a2b86456b
add option to insert an ack packet on autoack
2011-05-08 09:50:57 -04:00
Mariano Alvira
65671c66c6
turn on insert ack packet by default
2011-05-08 09:50:57 -04:00
Joakim Eriksson
3fa8da5ddf
fixed IAR compilation paths
2011-05-02 15:19:28 +02:00
Salvatore Pitrulli
5eabf33211
Added functions for deep sleep to mbxxx platform.
2011-04-27 18:12:23 +02:00
Mariano Alvira
d80449244d
Merge remote branch 'libmc1322x/master'
2011-04-20 21:23:47 -04:00
Salvatore Pitrulli
01a7a78a94
Fixed temperature ADC conversion bug on mbxxx.
...
The conversion was made from an incorrect source when
the GPIO pin was not PB7.
Added functions and macros used to select the correct
ADC channel.
2011-04-20 18:06:20 +02:00
Salvatore Pitrulli
aa968309af
Merge remote branch 'sf/master'
2011-04-16 16:27:10 +02:00
Niclas Finne
813489633c
Added missing include
2011-04-15 15:49:43 +02:00
Salvatore Pitrulli
4ff82b76e5
Removed -fsigned-char GCC compiler options.
2011-04-14 08:12:11 +02:00
Salvatore Pitrulli
0105057c44
Removed unwanted file.
2011-04-14 08:10:58 +02:00
Salvatore Pitrulli
0a0ad39c9b
Added weak symbols for STM32W exception handlers and other minor updates for the HAL.
2011-04-14 08:06:13 +02:00
Salvatore Pitrulli
57163c616d
Removed some warnings.
2011-04-14 08:05:21 +02:00
Salvatore Pitrulli
af8e58e063
Set LED pins to output when MB851 is in sleep mode.
...
This reduces power consumption.
2011-04-13 18:14:12 +02:00
dak664
2e14df3981
Options to extend mc1322x fifo to RAM buffer, or use hardware flow control with tunslip6.
2011-04-08 15:15:16 -04:00
Salvatore Pitrulli
6655c876f2
Added functions and example for deep sleep on mb851.
...
The added function let a process to make the system go
into deep sleep for maximum power saving.
The udp-ipv6-example shows how to use these new functions.
2011-04-08 11:53:48 +00:00
dak664
89741bd322
Exit on watchdog reboot call
2011-04-07 17:47:54 -04:00
dak664
581d081ffe
Don't use RF230_CONF_CCA_THRES if it is not defined.
2011-04-07 17:44:10 -04:00
Joakim Eriksson
f603c965c1
Merge branch 'master' of ssh://contiki.git.sourceforge.net/gitroot/contiki/contiki
2011-04-06 20:15:44 +02:00
Joakim Eriksson
928bf6b6c1
fixed cpu/msp430 for compilation with IAR compiler
2011-04-06 20:08:48 +02:00
Mariano Alvira
4f4e06c71b
Merge remote branch 'libmc1322x/master'
2011-04-06 05:56:06 -04:00
Oliver Schmidt
5da4faf71e
Allow VC++ to be used as alternative to GCC for building in the WIN32 target.
...
TODOs:
- Update README
- Add dependency handling
- Add rtimersupport
2011-04-03 22:32:11 +02:00
Oliver Schmidt
f83fb3704b
Replaced make-empty-symbols with empty-symbols.[c|h]
...
The symbol generation shell scripts cause CRLF issues on Windows/Cygwin again and again. Instead of fixing this yet again I opted to remove the symbol generation script at least for the "no symbols" scenario with two C source files to be copied.
2011-04-03 13:24:58 +02:00
dak664
a9cbbb4570
Add sneezer mode and tx power change
2011-03-23 18:08:07 -04:00
Mariano Alvira
11f5bca7c4
Merge remote branch 'libmc1322x/master'
...
Conflicts:
cpu/mc1322x/board/redbee-econotag.h
2011-03-22 16:28:08 -04:00
Salvatore Pitrulli
eb588f1aec
New HAL and SimpleMAC for STM32W108.
2011-03-22 19:35:49 +01:00
dak664
5dd7500d0b
Add configurable auto cca threshold and implement driver cca call.
...
Show smallest rssi in jackdaw menu.
2011-03-21 11:10:30 -04:00
dak664
d9b5bac953
Refactor with WATCHDOG_CONF_TIMEOUT
2011-03-14 16:14:47 -04:00
Mariano Alvira
74517b9df4
Merge remote branch 'libmc1322x/master'
2011-03-13 17:14:32 -04:00
dak664
59109b9893
Fix type, diagnostic interrupt code on conditional
2011-03-13 14:08:02 -04:00
dak664
a210e14d78
Add defines for watchdog configuration.
2011-03-13 13:45:12 -04:00
dak664
0b2d3d1615
Refactor clock code with optional interrupt optimizing.
...
Put periodic radio calibration on conditional.
2011-03-13 13:07:32 -04:00
dak664
0573ecd62f
Merge branch 'master' of ssh://contiki.git.sourceforge.net/gitroot/contiki/contiki
2011-03-11 16:51:10 -05:00
dak664
bf5be5056f
Testing $OS works with cygwin and DOS command windows
2011-03-11 16:50:35 -05:00
Mariano Alvira
f2b92cfa98
mc1322x: remove bad rule from cpu Makfile
2011-03-11 16:32:25 -05:00
Mariano Alvira
59d7fad746
Merge remote branch 'libmc1322x/master'
2011-03-11 16:28:14 -05:00
dak664
6a5c8ff1c4
Include file needed for slip rpl-border-router build
2011-03-11 14:10:30 -05:00
Mariano Alvira
a1ae79307b
mc1322x: remove auto reception mode as it appears to be the cause of
...
the periodic autoack checksum errors. removing auto mode doesn't seem
to create any performance issue.
2011-03-11 06:28:47 -05:00
dak664
bb574fd1e2
Don't create an object directory if target does not exist
2011-03-10 14:59:21 -05:00
Mariano Alvira
5208aa14ea
mc1322x: remove auto reception mode as it appears to be the cause of
...
the periodic autoack checksum errors. removing auto mode doesn't seem
to create any performance issue.
2011-03-08 15:36:53 -05:00
dak664
de7bcda99f
avrdude and makefile changes suggested by Georg von Zengen
2011-03-08 13:07:00 -05:00
Mariano Alvira
fa08b09770
Merge branch 'master' of git://git.devl.org/git/malvira/libmc1322x into update-lib
2011-03-07 12:37:26 -05:00
Mariano Alvira
2c79ab4962
mc1322x: increase the heap to 4K
2011-03-05 16:52:35 -05:00
Mariano Alvira
befbd4a479
mc1322x: handle board file differently if cygwin
2011-03-04 16:54:59 -05:00
Fredrik Osterlind
dd7cec737d
removed obsolete leds_[color]() functions, replaced by leds_{on,off}()
...
allow LEDS_[COLOR] to be configured by platform-conf
2011-03-03 17:48:32 +01:00
Mariano Alvira
f0c27340c6
mc1322x: increase the HEAP to 2048 bytes: needed for COAP server.
2011-02-25 16:10:08 -05:00
Mariano Alvira
bea643bc4a
mc1322x: flush the radio rx queue in the receive process
2011-02-23 15:19:45 -08:00
Mariano Alvira
c12ab0d484
mc1322x: get the tx status for a packet and return the proper response.
2011-02-23 15:19:44 -08:00
Mariano Alvira
535b9d35d7
mc1322x: disable broken maca calls for now.
...
maca_on, maca_off, and contiki_maca_init don't work correctly;
they mess up address filtering.
disable them for now and fix them later.
2011-02-23 15:19:44 -08:00
dak664
46297de770
Allocate variable only when mass storage is enabled
2011-02-23 14:06:06 -05:00
Mariano Alvira
c857e57d2f
msp430: fix "implicit declaration of function" warnings in clock.c, by including watchdog.h
2011-02-21 09:23:52 -08:00
Mariano Alvira
8f9cf50e55
set timestamp packet attribute
2011-02-18 12:46:34 -05:00
Mariano Alvira
a86a0fbe0e
set lqi packet attribute
2011-02-18 12:46:10 -05:00
Mariano Alvira
07f77b02eb
Merge remote branch 'libmc1322x/master'
2011-02-18 12:38:30 -05:00
Mariano Alvira
2e331b51e8
Merge remote branch 'libmc1322x/master' into update-libmc1322x
...
Conflicts:
cpu/mc1322x/COPYING
2011-02-17 14:41:47 -05:00
Mariano Alvira
2e33e1694a
Merge branch 'libmc13-9f82e068' into update-libmc1322x
2011-02-17 14:39:20 -05:00
Mariano Alvira
7cdfbb0947
remove cvs keywords from cpu/mc1322x
2011-02-17 14:36:55 -05:00
Mariano Alvira
bfb471c782
add proper arm flags and remove Makefile.src as it's not used.
2011-02-08 09:55:50 -05:00
Mariano Alvira
b1dd3fc063
use the CS toolchain by default:
...
http://www.codesourcery.com/sgpp/lite/arm/portal/release642
2011-02-08 09:55:23 -05:00
Mariano Alvira
81552d1f6d
add a tutorial for rest-example
2011-02-08 09:08:05 -05:00
Mariano Alvira
5c3ef556d9
add a dummy io.h for mc13224v
2011-02-08 09:07:54 -05:00
Mariano Alvira
f5ba70cd20
add heap and _sbrk to mc13224v
2011-02-08 09:07:23 -05:00
Mariano Alvira
9572baa71b
fix mc13224v led driver to only touch gpio used for leds.
2011-02-08 09:07:11 -05:00
dak664
5c098993df
Add initial file
2011-02-07 20:30:47 -05:00
dak664
b41e8f384e
Add initial atmega128rfa1 file
2011-02-07 20:28:17 -05:00
dak664
f1f32c8e6a
Add combined MCU and radio ATmega128rfa1
2011-02-07 13:46:34 -05:00
Mariano Alvira
2a75a4a5df
this fixes a major problem with the maca_process
...
Before it didn't do process_poll like it should and would add events
out of turn and mess up the event processor --- that would cause the
button to stop working after the unhandled events exceeded a max
number
this fixes maca_process to do a process_poll as it should. now the
button works fine and so does the radio.
2011-02-03 18:09:51 -05:00
oliverschmidt
8c87f85a1d
Made cc65 build compatible with make.exe from GnuWin32 and cmd.exe. We just live without the phony targets when building with cmd.exe - the next cc65 release will make the whole sed thingy obsolete anyway :-)
2011-01-23 16:30:30 +00:00
joxe
801a7e1149
fixed bug with uart DMA
2011-01-19 20:44:20 +00:00
salvopitru
5fcae86be3
Now it is putchar that has to be redefined (instead of __io_putchar), like other platforms.
2011-01-19 09:13:06 +00:00
adamdunkels
8f283b3989
Bugfix
2011-01-19 07:30:31 +00:00
adamdunkels
6f076dbe1a
A set of compiler options that reduce the size of the final code size and RAM usage with ~10%. Courtesy of Simon Duquennoy.
2011-01-19 07:24:37 +00:00
maralvira
68180c0574
use network 230 --- 802.15.4 no-FCS
2011-01-18 16:58:18 +00:00
adamdunkels
bb2e3b25bd
Larger default DMA tx buffer size, to allow SLIP operation. Warn if DMA is enabled, since MSPsim does not yet support it.
2011-01-18 16:07:16 +00:00
maralvira
ce92a90e58
new timer setup routines.
2011-01-17 15:51:19 +00:00
maralvira
b3c8c14b7d
add timer setup routines
2011-01-17 15:51:02 +00:00
maralvira
ca098db611
fix a race condition regarding advancement of the softclock. Without
...
this, the advancment would fail to trigger a tx cycle
occasionally. This would cause the packet to get deferred until the
next expiration of the softclock.
2011-01-17 15:49:17 +00:00
maralvira
40bb4b80dc
whitespace fixup to sync with libmc1322x
2011-01-17 15:48:39 +00:00
maralvira
6fb75263f9
fix parsing and pcap generation for packets with multiple output lines
...
(those that are > 16 bytes).
2011-01-17 15:47:23 +00:00
maralvira
d82b004154
fix parsing and pcap generation for packets with multiple output lines
...
(those that are > 16 bytes).
2011-01-17 15:47:08 +00:00
maralvira
d0227afbed
cycle channel on keypress.
2011-01-17 15:46:27 +00:00
maralvira
c78e1e345e
add stdint.h
2011-01-17 15:45:02 +00:00
maralvira
0445a4f78f
add cmdline options to set the intercharacter delays.
2011-01-17 15:44:18 +00:00
maralvira
fb8c08ca7c
only use these stubs with linux toolchains
2011-01-17 15:42:24 +00:00
salvopitru
9aa734936f
RANDOM_MAX changed to RANDOM_RAND_MAX.
2011-01-17 10:08:14 +00:00
salvopitru
fb75503624
'BTM' can be defined to flash devices already in bootloader mode.
...
COFFEE_FILES changed to COFFEE.
2011-01-17 09:41:47 +00:00
salvopitru
a9b1b37bec
Added definition of BAUD2UBR macro.
2011-01-17 09:22:24 +00:00
adamdunkels
f002563e60
Tx on interrupts occasionally misses characters on output. Therefore we turn it off by default.
2011-01-09 20:44:14 +00:00
ksb
eb24078ffb
Converted CRLF line endings to LF
2011-01-05 17:16:42 +00:00
joxe
5b7b3da99c
minor fixes of DMA uart code
2011-01-05 13:36:38 +00:00
joxe
565fda47aa
added initial uart1 DMA rx support and required LPM requirements api
2011-01-05 12:02:01 +00:00
dak664
90a6d768ea
Keep track of sleeptime and display on status web page.
2010-12-23 19:41:07 +00:00
dak664
662b0e064c
Revert Larsson patch, setting this to 0x3f truncated jackdaw Tx packets to 64 bytes.
2010-12-22 22:49:16 +00:00
dak664
95982b40ba
$make will show avr-size once and only once whether or not a build needs to occur.
2010-12-22 21:13:09 +00:00
dak664
5b8e62ef4f
Patches from R Larsson
2010-12-22 20:10:00 +00:00
dak664
013c3ac2f8
Remove contitional on clock updating, it should always be done after a sleep!
2010-12-22 17:09:03 +00:00
dak664
44a2e34005
Resolve TIMER2 conflict between sleep and possible clock usage.
2010-12-22 16:50:30 +00:00
dak664
e3e1e04948
Add FCS comments and text2pcap dump routines of Roger Larsson.
...
Don't send last two byte to xmit buffer since they will be overwritten by the checksum anyway.
2010-12-21 04:25:15 +00:00
dak664
e4b0b3dc8c
Disable watchdog software counter. Nested watchdog stop/starts will not work, but the low power protocols will.
2010-12-18 20:51:11 +00:00
dak664
5623ad827b
Enable radio off and sleep modes.
2010-12-18 20:49:00 +00:00
adamdunkels
f370b217a5
Turned up the rtimer resolution to 32678 Hz.
2010-12-16 22:50:21 +00:00
adamdunkels
1d090ea0f5
Made configuration of CC2420 SFD timestamps easier
2010-12-16 22:49:33 +00:00
adamdunkels
c0fedd7661
Store timestamps in the cc2420 module instead of the cc2420-arch-sfd module
2010-12-16 22:49:12 +00:00
dak664
570f6e705f
Move conditional needed by previous commit.
2010-12-15 19:32:49 +00:00
dak664
aa7ad8c807
Add rf230_listen_channel routine to force RX_ON state for sniffing and to read rssi for energy scan.
2010-12-15 16:50:44 +00:00
salvopitru
d0db3fc39a
Added a check for Coffee start address.
2010-12-15 15:01:00 +00:00
dak664
1cc336f188
Conditional code to use hardware multiply by default.
2010-12-15 14:11:06 +00:00
salvopitru
5fe80dd99d
Added elfloader machine dependent code for STM32W.
2010-12-15 11:10:20 +00:00
dak664
c784e8bc46
Enable RX_START interrupt and read rssi at end of preamble when not using energy detect register
2010-12-14 22:34:18 +00:00
dak664
9c9d7ec5e9
Return TRAC_STATUS register when tx autoretry is enabled.
2010-12-05 17:28:29 +00:00
dak664
35b2ce0cdb
Add status page link, show correct rssi, fix indexing off array in ipv4 builds
2010-12-04 21:32:35 +00:00
dak664
58b7a19803
Hardware/software radio HAL patch from Roger Larsson.
...
Use CHANNEL_802_15_4 define for RF channel on all AVR platforms, default 26.
Remove hopefully unnecessary interrupt disable wrapper on eeprom reads and writes.
2010-12-03 20:42:01 +00:00
dak664
21b10e8021
Convert obsolete MCU_MHZ to F_CPU and add 14745600MHz case using patch from Tobias Schfer
2010-12-03 18:16:56 +00:00
dak664
0ba9846abd
Add macros by Roger Larsson to select between hardware or software SPI transactions.
...
Minor speed optimizations.
2010-11-30 19:47:40 +00:00
nifi
7110afdad5
added missing include
2010-11-27 15:27:20 +00:00
dak664
dc028b3f85
Get rssi correctly in either rx mode, clean up radio driver debugging
2010-11-26 20:39:15 +00:00
adamdunkels
149f4e8d21
Enable the watchdog for rtimers too. Removed the disabling of the TACTL - it should not be needed, and interferes with the timing behaviour of stable rtimers
2010-11-25 09:22:56 +00:00
dak664
880233a451
RSSI read fix (use ED register in AACK mode), add reduced power configuration for miniature mesh testing.
2010-11-24 18:46:57 +00:00
adamdunkels
4fac3037e0
Fixed a bug found by Moritz Straube - writing to the internal flash would lock up contikimac. The problem was due to the IFG1 being reset to zero before writing to flash.
2010-11-15 21:52:54 +00:00
dak664
69ef9d57eb
sizeof(*) is sizeof first array element
2010-11-12 17:24:36 +00:00
dak664
9e94ba9803
Allow non-ipv6 build, e.g. Hello World
2010-11-12 17:15:00 +00:00
nifi
5de83c9085
Only include code for stack printouts when needed
2010-11-12 15:54:41 +00:00
maralvira
3426eae031
fix typos
2010-11-11 20:37:33 +00:00
maralvira
9b2a2bb5e6
fix up stdint include
2010-11-10 22:12:29 +00:00
maralvira
6da84819dd
use stdint.h instead of custom types.h
...
stdint.h is more portable across compilers
2010-11-10 22:06:28 +00:00
maralvira
e229022f38
include crm.h
2010-11-10 21:58:12 +00:00
salvopitru
28e1445a0f
Added a simple implementation of Coffee for STM32W108.
2010-11-10 11:20:44 +00:00
maralvira
dfbc81158b
Allow CROSS to be overridden with CROSS or CROSS_COMPILE
2010-11-09 13:13:45 +00:00
maralvira
1aac14f252
add tutorial explaining how to set up an RPL network of econotags
2010-11-09 01:30:01 +00:00
maralvira
3b515587c5
change how prepare and transmit work --- Contiki expects to call
...
prepare once and then transmit many times to repeat the same packet
over and over. This didn't work like that, but now it does.
2010-11-07 20:07:42 +00:00
maralvira
e029fa8da0
fix defines for raw mode
2010-11-07 18:34:52 +00:00
maralvira
4664151419
fix build errors with start.S
2010-11-07 15:19:45 +00:00
maralvira
29333232d5
add section .start and undef _start so that _start is placed by the
...
linker correctly
2010-11-07 14:57:53 +00:00
maralvira
b8ebce0fef
add a memory section for RAM so that the linker will warn when you've
...
made your program too big.
2010-11-07 14:54:05 +00:00
maralvira
8385536c41
fix how start object is linked
2010-11-07 14:52:23 +00:00
maralvira
f38598ce9f
clear BSS
2010-11-07 14:49:42 +00:00
maralvira
57513948c9
Move stack near BSS so it doesn't take up space in the .bin
2010-11-07 14:48:52 +00:00
maralvira
77cf0f0f5e
update ring_osc_on and _off to the new bit structs
2010-11-07 14:42:31 +00:00
maralvira
c8056cc4e2
define TCF TCF1 and TCF2 --- the new bit structs don't work here for
...
some reason.
2010-11-07 14:42:02 +00:00
maralvira
dab7faf13c
Add gpio_set and gpio_reset
...
Use them like gpio_set(GPIO_xx) and gpio_reset(GPIO_xx).
These macros efficiently set the DATA_SET and DATA_RESET bits without
reading the registers first, as a direct GPIO->DATA_SET.GPIO_xx would do
2010-11-07 14:29:04 +00:00
maralvira
4a4a39c84a
Name the GPIO structure so we can set multiple bits at once
2010-11-07 14:28:30 +00:00
maralvira
4217eb2ebc
Provide a function to change timer interrrupt handlers
...
Function irq_register_timer_handler(int timer, void (*isr)(void))
lets you change the handler at runtime. This lets us set handlers
without necessarily knowing the name at link-time. The old way of
having weakly-linked tmr0_isr functions should still work.
2010-11-07 14:27:01 +00:00
maralvira
65d3942c76
Add the disable_int({}) macro
...
This is similar to safe_irq_enable and disable
2010-11-07 14:26:24 +00:00
maralvira
83e6995af1
Add TMR_ADDR helper
2010-11-07 14:25:07 +00:00
maralvira
d930ce0e2b
Add some useful timer macros
2010-11-07 14:24:36 +00:00
maralvira
5e00219a9c
Register definitions: get rid of some macro magic that doesn't help much
...
Instead of e.g. GPIO.DATA.GPIO_08, you now use GPIO->DATA.GPIO_08.
2010-11-07 14:24:11 +00:00
maralvira
091e4cd84e
Add structure-based ITC access
2010-11-07 14:23:15 +00:00
maralvira
11ac20a361
REF_OSC is a 32-bit number, not 64-bit number
2010-11-07 14:22:51 +00:00
maralvira
745e7b5ac2
Add cal_isr() support
2010-11-07 14:21:59 +00:00
maralvira
ab84453401
Add structure-based CRM definitions
2010-11-07 14:21:33 +00:00
maralvira
9d072d5309
Add macro to help compute TMR.ENBL values (useful when using #defined
...
values to represent timers)
2010-11-07 14:21:06 +00:00
maralvira
85e6b06175
Add pin definitions for each timer, they're fixed
2010-11-07 14:19:17 +00:00
maralvira
8d2f740f7f
Fix #ifdefs in board files
2010-11-07 14:18:54 +00:00
maralvira
3726588f02
Add structure-based GPIO register definitions
2010-11-07 14:17:45 +00:00
maralvira
20b477db13
Add structure-based timer register definitions
2010-11-07 14:17:20 +00:00
maralvira
c71a0243ff
Add missing type for TMR0_COMP2
2010-11-07 14:16:28 +00:00
maralvira
62a45c7ba2
Add script to invoke kermit with a particular port and speed
2010-11-07 14:15:40 +00:00
maralvira
2ac88222f6
Use "rm -f" in clean rules to ignore errors
2010-11-07 14:14:47 +00:00
maralvira
2e87143381
use kermit in open-terms
2010-11-07 14:13:22 +00:00
maralvira
c8be3047c3
fix byte ordering in burn-macs
2010-11-07 14:12:55 +00:00
maralvira
0450b3fd90
add script that burns the mac address only --- mac address is Redwire
...
IAB + tty number.
2010-11-07 14:12:27 +00:00
maralvira
f913cf728b
modify flasher.c to not create a vaild boot magic number if the length
...
of the file is zero
modify mc1322x-load.pl to optionally send a zero length file with -z;
extra data on the command line is still written.
This allows you to burn the mac adress without flashing a vaild image.
2010-11-07 14:11:50 +00:00
maralvira
9f7d860e9c
add scripts to help load a bunch of econotags
2010-11-07 14:11:18 +00:00
maralvira
8b2ef2675d
discard received packets --- this lets you run multiple rftest-tx's at
...
the same time.
2010-11-07 14:10:16 +00:00
maralvira
e00349509d
add simple install rule
2010-11-07 14:09:43 +00:00
maralvira
ee943c062d
add autoreset command and do_exit option
2010-11-07 14:08:50 +00:00
maralvira
e886e83908
fix bug in print_packet
...
Thanks dean and jim.
2010-11-07 14:07:33 +00:00
maralvira
f1fede7090
get LQI of received packets
2010-11-07 14:06:57 +00:00
maralvira
ae0b7f846f
Fix the CNTR defines.
...
Thanks to Ruslan for finding this.
2010-11-07 14:04:59 +00:00
maralvira
646a37f8b3
use the hardware random number generator
2010-11-07 13:52:12 +00:00
dak664
eb0d5c7f45
Add missing includes
2010-11-03 16:55:40 +00:00
oliverschmidt
1dfe490f9b
Use some defined event constant instead of just 0.
2010-10-31 22:51:17 +00:00
dak664
9194b3ac69
Fix error when RS232 not enabled
2010-10-28 19:31:28 +00:00
dak664
ad6712736b
Fix Windows XP RNDIS+CDC serial port enumeration
2010-10-28 19:30:14 +00:00
dak664
258e3cc93a
Allow simultaneous use of RS232 and USB serial ports
2010-10-27 14:51:20 +00:00
salvopitru
d8711d32a3
Added configuration in order to run Rime.
2010-10-27 14:05:23 +00:00
salvopitru
db3f1864a0
Increased minimum stack size, because rpl uses it much more.
2010-10-26 11:07:20 +00:00
salvopitru
33ccbbb509
Fixed compile error raised after rand.c removal.
2010-10-26 10:47:23 +00:00
salvopitru
444a00949a
Added missing libraries.
2010-10-26 10:24:17 +00:00
salvopitru
790f13a689
More safe detection of cygwin path.
2010-10-26 07:26:40 +00:00
salvopitru
ec5e3ce0d7
New Contiki port to STM32W108.
2010-10-25 09:03:38 +00:00
adamdunkels
34f6a60a4a
By default, don't print stack on reboot, since there are cases where this may hang the CPU (when the CPU is in LPM when the watchdog triggers). Must fix the code to set the UART and CU into correct modes before enabling stack printout on reboot.
2010-10-24 21:10:25 +00:00
oliverschmidt
9a8c62a629
Removed remark on using cc65 snapshot.
2010-10-23 19:42:53 +00:00
dak664
123e3cae41
Fix compiler warnings
2010-10-23 15:26:46 +00:00
oliverschmidt
5e10cf2eed
Implemented cfs_opendir() and friends for CBMs based on cc65's cbm_opendir() and friends.
2010-10-23 13:48:06 +00:00
oliverschmidt
9e9eb4b55c
There's no point in pulling in cfs-posix-dir.c if the POSIX functions it depends on are dummies anyway.
2010-10-23 08:17:45 +00:00
oliverschmidt
b84f771c6b
The recent change in core/net/mac/lpp.c requires CLOCK_SECOND to be at least twice NETSTACK_RDC_CHANNEL_CHECK_RATE in order to compile.
2010-10-22 20:28:58 +00:00
dak664
7be7a34bbb
Fix windows COM port enumeration
2010-10-22 19:15:43 +00:00
dak664
774474b7aa
Fix compiler warning
2010-10-20 18:57:33 +00:00
oliverschmidt
842c6a018a
The recent global change regarding htons allowed to remove this hack :-)
2010-10-19 20:30:47 +00:00
adamdunkels
5585d72c86
A simple but substantial change: uIP used the htons()/HTONS() macro
...
functions for converting between host and network byte order. These
names are the de facto standard names for this functionality because
of the original BSD TCP/IP implementation. But they cause problems for
uIP/Contiki: some platforms define these names themselves (Mac OS,
most notably), causing compilation problems for Contiki on those
platforms.
This commit changes all htons to uip_htons instead. Same goes for
htonl, ntohs, and ntohl. All-caps versions as well.
2010-10-19 18:29:03 +00:00
oliverschmidt
35f7b6046e
Fixed 'Modulo operation with zero' error by making sure that NETSTACK_CONF_RDC_CHANNEL_CHECK_RATE is not smaller than CLOCK_CONF_SECOND.
2010-10-06 19:48:26 +00:00
oliverschmidt
a40594b7ce
Display correct name of statically loaded driver.
2010-09-29 21:48:54 +00:00
oliverschmidt
c839eacbdf
Added cc65 target 'atari' for Atari 8-bit machines. This addition was triggered by exsistence of http://www.atari8ethernet.com/ .
2010-09-29 19:44:01 +00:00
oliverschmidt
55d61d317b
Allow cc65 ethernet drivers to be loaded statically instead of dynamically. This saved quite some space in scenarios without additional cc65 drivers to be loaded for i.e. a mouse because in those scenarios the cc65 module loader isn't necessary. And without the module loader typically the cc65 heap manager isn't necessary.
2010-09-28 23:02:16 +00:00
adamdunkels
7c14899eeb
Made stack printout on reboot configurable.
...
Added the ability to turn on watchdog multiple times - the watchdog
registers are touched only when the watchdog goes from off to on state
to avoid retriggering the watchdog when it shouldn't.
2010-09-22 22:12:37 +00:00
dak664
110bc0242e
Merge CDC-ECM, RNG, DFU bootloader, watchdog, settings manager, energy scan routines of Robert Quattlebaum
2010-09-17 21:59:09 +00:00
nifi
f5ea831445
Added function rtimer_arch_now that makes sure that the timer value does not change between readouts to avoid reading while the timer is being updated.
2010-09-13 20:51:09 +00:00
maralvira
1cb0762bd0
Don't post from an interrupt context --- this resulted in process
...
corruption if a packet was received at the wrong time.
The maca_thread now just PAUSEs and checks rx_head instead of waiting
for a data event to be posted.
2010-09-13 14:15:58 +00:00
joxe
c0549cad3d
added some files for MSP430X I/O
2010-08-24 16:23:20 +00:00
maralvira
df9d43ab83
increase the reception time now that tx_packet will advance the timer
...
as necessary.
2010-07-28 18:49:34 +00:00
maralvira
9a7a2742b3
remove bad call to maca_on()
...
maca_on() resets the maca and phy, takes a long time, and clobbers any
packet that is currently being transmitted or received. It doesn't
belong in prepare and was the source of a lot of latency and bad
packet transmissions.
Make sure the maca is on somewhere else.
2010-07-28 18:48:51 +00:00
maralvira
a3b9c2adb0
in tx_packet, force an interrupt if the maca isn't doing anything so
...
that the transmit starts. Or if the maca is in a reception cycle,
advance the softclock timeout to now so that transmission starts as
soon as possible (immediately if a packet isn't being received or
right after reception finishes).
2010-07-28 18:48:03 +00:00
maralvira
593a50c38f
make the debug prints in check_maca more specific
2010-07-28 18:47:35 +00:00
maralvira
422d05003f
use 32 packets in the pool by default
2010-07-28 18:47:05 +00:00
maralvira
eb0e3b7989
fix long standing bug where the last pages of NVM were not erased
...
properly.
2010-07-28 18:43:04 +00:00
oliverschmidt
c602c61468
Activated Platform-specific File System (PFS) for the C64/C128 by default for all programs with R/W CFS access.
2010-07-22 10:30:12 +00:00
oliverschmidt
9c0f5d857c
Updated API for uiplib and resolv to use uip_ipaddr_t instead of uint16_t.
2010-07-21 22:35:59 +00:00
maralvira
5b44d6a29a
properly drop characters when buffer is full
...
fix by David Kopf
2010-07-06 13:39:34 +00:00
joxe
0c5390339f
updated to new cc2420 spi naming
2010-06-23 10:44:41 +00:00
joxe
705f8cc451
fixed naming of SPI and CC2420 related code
2010-06-23 10:19:15 +00:00
dak664
898c00b812
Remove usually extra avr-size command
2010-06-22 17:11:38 +00:00
dak664
e45b1c042b
TIMER2 uses TIMER2 interrupt vector!
2010-06-22 16:17:24 +00:00
dak664
ab7f3bd8e3
Option to use 32768Hz watch crystal for timing. Code suggested by Georg von Zengen.
2010-06-18 17:30:30 +00:00
dak664
cb45883970
Turn on DEBUGFLOW and software CRC computation
2010-06-18 15:44:53 +00:00
nifi
20c8b4f9c6
removed obsolete comments
2010-06-15 13:30:42 +00:00
adamdunkels
3fa8ffda1a
Moved the modules packetbuf, queuebuf, and packetqueue from net/rime to net/, since they are not Rime-specific
2010-06-14 19:19:16 +00:00
maralvira
419906a769
initial mc1322x commit
...
based on commit aac3a355451d899f02737f2907af8c874ee4feba of
git://git.devl.org/git/malvira/contiki-mc1322x.git
2010-06-10 14:55:39 +00:00
maralvira
285f508cc9
initial commit of src files
2010-06-10 14:49:31 +00:00
maralvira
bf9f960bbe
add board files.
2010-06-10 14:48:32 +00:00
maralvira
1145fa9ba9
initial mc1322x commit
...
based on commit aac3a355451d899f02737f2907af8c874ee4feba of
git://git.devl.org/git/malvira/contiki-mc1322x.git
2010-06-09 14:43:22 +00:00
oliverschmidt
d28865abac
Adjusted hacky inline assembler to reference uip_aligned_buf instead of uip_buf - some day I'll need to clean up that (btw bogus) code.
2010-05-30 10:12:30 +00:00
oliverschmidt
126ea40994
Removed UIP_CONF_PLAIN_BUFFER again now that the pointer indirection to uip_buf was removed again.
2010-05-30 09:46:12 +00:00
nifi
808116ff56
Made SFD timestamps configurable via external definition
2010-05-10 11:32:44 +00:00
oliverschmidt
2169932727
Have the cc65 based targets stay with the "old" plain uip_buf.
2010-05-08 07:25:10 +00:00
dak664
972e2f5d4f
Add MCU to avr-size command; Remove fuse and signature from .hex; Give bootloader more memory
2010-05-04 14:14:49 +00:00
nifi
9638789d9d
Added rule to use MSPSim to show the maptable from the last compilation on MSP430 targets
2010-04-20 15:38:09 +00:00
oliverschmidt
7b5bde6336
Made the maximum number of concurrent TCP connections a highlevel config value.
2010-04-11 20:47:16 +00:00
anthony-a
04fb6e5b42
initial add.
2010-04-10 21:18:32 +00:00
anthony-a
3de90a9671
fix adc compile errors when HAVE_DMA is not true.
...
remove reference to brione_lcd.h
turn off DEBUG messages.
2010-04-10 19:59:37 +00:00
oliverschmidt
21f8e4e982
Made MAC_CONF_CHANNEL_CHECK_RATE identical to CLOCK_CONF_SECOND in order to make sure it isn't larger - which causes 'divide by zero' errors.
2010-04-05 15:17:22 +00:00
oliverschmidt
9831f02eba
Replaced dummy code with code taken from 'native'.
2010-04-05 15:13:50 +00:00
oliverschmidt
ffce456612
If rtimer_arch_now() is mapped to clock_time() it seems reasonable to map RTIMER_ARCH_SECOND to CLOCK_CONF_SECOND for consistency reasons.
2010-04-05 15:10:06 +00:00
oliverschmidt
26e61ac3f7
Programs using CFS should #include "cfs.h" ;-)
2010-04-05 13:41:29 +00:00
adamdunkels
5eb22ad289
Print out stack pointer when rebooting node
2010-04-04 12:30:10 +00:00
adamdunkels
0ed236e774
Bugfix: the clock interrupt now flushes the energy estimator to avoid overflow of the LPM mode
2010-04-04 12:29:50 +00:00
adamdunkels
52ad0008dc
Bugfix
2010-03-31 11:55:04 +00:00
adamdunkels
4447782ab4
Print out a stack trace when a node reboots because of the watchdog
2010-03-30 23:02:23 +00:00
adamdunkels
ac172a5575
Turn off LPM mode for clock interrupts to avoid rtimer wrapping during extended LPM
2010-03-29 21:53:32 +00:00
oliverschmidt
54e19782ae
Moved PFS header from Apple2 directory to 6502 directory as we're going to have other PFS implementations.
2010-03-27 15:16:57 +00:00
oliverschmidt
6769e6a99f
- Moved PFS header from Apple2 directory to 6502 directory as we're going to have other PFS implementations.
...
- Completed declarations.
2010-03-27 14:46:08 +00:00
nifi
ebfa6c5ef1
only include memcpy/set workaround when needed
2010-03-21 10:40:15 +00:00
joxe
e99c906caf
activated the new workaround...
2010-03-19 14:50:07 +00:00
joxe
7e6919cc8c
fixed workaround for memcpy/set to be memory efficient but slower
2010-03-19 14:39:45 +00:00
adamdunkels
04cdae05c3
Increased the rtimer granularity: needed to make contikimac work
2010-03-19 13:25:52 +00:00
dak664
0265f09a5c
Add RS232 port option to jackdaw USB stick
2010-03-15 18:52:55 +00:00
fros4943
db777ce3d0
reverted previous patch: appears to create problems on hardware
2010-03-05 12:06:03 +00:00
nvt-se
7543d53603
Ensure that the UART port is available before writing
2010-03-03 23:18:58 +00:00
dak664
01a3912864
Define and use radio STATE_TRANSITION, improve debug messaging
2010-03-02 16:29:59 +00:00
dak664
39e6f6a830
Clean up, functional webserver for further testing of low power protocols
2010-02-28 21:29:19 +00:00
dak664
d61676b8f7
Add RADIOALWAYSON to monitor packet losses with low power protocols
2010-02-28 21:19:33 +00:00
dak664
5debc183a9
Enable radio stats in sensor cgi as default
2010-02-26 21:38:57 +00:00
dak664
844b3a34f7
Platform 0 was matching by default
2010-02-26 21:15:28 +00:00
dak664
195f5939c4
Clean up after testing
2010-02-26 20:51:48 +00:00
adamdunkels
465125c5e7
Added support for 32-bit clock ticks: when reading the 32-bit value, make sure that it does not change between readouts to avoid reading right in the middle of it being updated
2010-02-23 18:41:20 +00:00
dak664
7274f1d1ed
Report operating channel with either radio driver
2010-02-23 17:40:09 +00:00
dak664
4ded42db1e
Add sniffer and 802 frame reporting
2010-02-23 17:37:51 +00:00
dak664
b4bc7fc3da
Make RF230BB the default radio driver
2010-02-23 02:01:46 +00:00
dak664
cbb8621e30
update to new driver format
2010-02-22 22:23:18 +00:00
dak664
658c35df11
remove debug printf
2010-02-22 22:21:15 +00:00
adamdunkels
953a8c2015
Turn off timer before updating - needed to avoid bugs in ContikiMAC - not 100% sure why
2010-02-18 22:15:54 +00:00
oliverschmidt
1817acae15
Now that the C64 mouse driver works we can activate the mouse support for this target :-)
2010-02-18 21:30:31 +00:00
dak664
a83381de30
add rtimers for cxmac
2010-02-18 17:21:44 +00:00
dak664
fee5efb141
additions for cxmac
2010-02-18 17:20:50 +00:00
dak664
98b69e1bff
No sniffer yet for RF230BB
2010-02-16 22:55:20 +00:00
dak664
23f6949af6
RF230BB addition
2010-02-16 22:51:40 +00:00